The i219 appears to have a seriously broken reset mechanism. After
any transmit or receive activity, resetting the card will break both
the transmit and receive datapaths until the next PCI bus reset.
The Linux and BSD drivers include a convoluted workaround authored by
Intel which involves setting a bit in the undocumented FEXTNVM11
register, then transmitting a dummy 512-byte packet containing garbage
data, then reconfiguring the receive descriptor prefetch thresholds
and temporarily reenabling the receive datapath. The comments in the
Intel fix do not even remotely match what the code actually does, and
the code accidentally leaves the transmitter enabled after use.
Experimentation suggests that an equivalent fix is to simply set the
undocumented bit in FEXTNVM11 before enabling the transmit or receive
descriptor rings.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of gcc (observed with gcc 4.7.2) report a spurious
uninitialised variable warning in ena_get_device_attributes(). Work
around this warning by manually inlining the relevant code (which has
only a single call site).
Reported-by: xbgmsharp <xbgmsharp@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most drivers do not utilise an MII interface, since the link state is
typically available directly from a memory-mapped register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The SnpDxe driver raises the task priority level to TPL_CALLBACK when
calling the UNDI entry point. This does not appear to be a documented
requirement, but we should probably match the behaviour of SnpDxe to
minimise surprises to third party code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification has an implicit and demonstrably incorrect
requirement (in the Mem_IO() calling convention) that any UNDI network
device has at most one memory BAR and one I/O BAR.
Some UEFI platforms have been observed to report the existence of
non-existent additional I/O BARs, causing iPXE to select the wrong
BAR. This problem does not affect the SnpDxe driver, since that
driver will always choose the lowest numbered existent BAR of each
type.
Adjust iPXE's behaviour to match that of SnpDxe, i.e. to always select
the lowest numbered BAR(s).
Debugged-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Debugged-by: Adklei <adklei@realtek.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The LAN78xx datapath is essentially identical to that of the SMSC75xx.
Expose the transmit, poll, and bulk IN endpoint operations to allow
for reuse by the LAN78xx driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The LAN78xx PHY interrupt source and mask registers do not match those
used by the SMSC75xx and SMSC95xx.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since we don't enable IOMMU at all, we can then simply enable the
IOMMU support by claiming the support of VIRITO_F_IOMMU_PLATFORM.
This fixes booting failure when iommu_platform is set from qemu cli.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The smsc75xx and smsc95xx drivers include a substantial amount of
identical functionality, varying only in the base address of register
sets. Abstract out this common functionality to allow code to be
shared between the drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Xen network backend (xen-netback) suffered from a regression
between upstream Linux kernels 3.18 and 4.2 inclusive, which would
cause packet reception to fail unless at least 18 receive buffers were
available. This bug was fixed in kernel commit 1d5d485 ("xen-netback:
require fewer guest Rx slots when not using GSO").
Work around this bug in affected versions of xen-netback by providing
the requisite 18 receive buffers.
Reported-by: Taylor Schneider <tschneider@live.com>
Tested-by: Taylor Schneider <tschneider@live.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An "enlightened" external bootloader (such as Windows Server 2016's
winload.exe) may take ownership of the Hyper-V connection before all
INT 13 operations have been completed. When this happens, all VMBus
devices are implicitly closed and we are left with a non-functional
network connection.
Detect when our Hyper-V connection has been lost (by checking the
SynIC message page MSR). Reclaim ownership of the Hyper-V connection
and reestablish any VMBus devices, without disrupting any existing
iPXE state (such as IPv4 settings attached to the network device).
Windows Server 2016 will not cleanly take ownership of an active
Hyper-V connection. Experimentation shows that we can quiesce by
resetting only the SynIC message page MSR; this results in a
successful SAN boot (on a Windows 2012 R2 physical host). Choose to
quiesce by resetting (almost) all MSRs, in the hope that this will be
more robust against corner cases such as a stray synthetic interrupt
occurring during the handover.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On most Intel NICs, Auto-Speed Detection Enable (ASDE) can be used to
automatically detect the correct link speed by sampling the link using
the internal PHY. This feature is automatically inhibited when not
appropriate for the physical link (e.g. when using internal SerDes
mode on the 8254x).
On the i350 datasheet ASDE is a reserved bit, but the relevant
auto-speed detection hardware appears still to be present. However,
enabling ASDE on the i350 1000BASE-KX backplane NIC seems to cause an
immediate link failure. It is possible that the auto-speed detection
hardware is still present, is not connected to a physical link, and is
not inhibited from being applied in this mode.
Work around this problem by adding an INTEL_NO_ASDE flag bit
(analogous to INTEL_NO_PHY_RST), and applying this for the i350
backplane NIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In situations where iPXE fails to reach link-up as expected, it is
useful to know the original values of the CTRL and STATUS registers
prior to our reset attempt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Following changes were introduced:
- added GetBgxProp and GetLmacProp methods to ThunderxConfigProtocol
- replaced direct BOARD_CFG access with usage of introduced methods
- removed redundant BOARD_CFG
- changed GUID of ThunderxConfigProtocol, as this is not compatible
with previous version
- changed UINTN* to UINT64* buffer type to fix issue on 32-bit
platforms with MAC address
This change allows us to avoid alignment of BOARD_CFG definitions
every time it changes in UEFI.
Signed-off-by: Konrad Adamczyk <konrad.adamczyk@cavium.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL
(1<<16), so use a 32bit read when testing Y2_VAUX_AVAIL.
[This patch is copied directly from the Linux kernel tree.]
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The value of ( ( x & 0x0c00 ) | 0x0c00 ) is always 0x0c00 regardless
of the value of x, and so the read_csr() is redundant. (There are no
read side effects for this register, according to the datasheet.)
This line of code originated in Linux kernel 2.3.19pre1 as
a->write_csr(ioaddr, 80, a->read_csr(ioaddr, 80) | 0x0c00);
and was modified in kernel 2.3.41pre4 to read
a->write_csr(ioaddr, 80, (a->read_csr(ioaddr, 80) & 0x0C00) | 0x0c00);
In the absence of commit messages, the intention of the code is
unclear. However, the logic resulting in a fixed value of 0x0c00 has
remained unaltered for over 17 years, and can probably be assumed to
have the correct overall result.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Any underlying errors arising during ib_create_cq() or ib_create_qp()
are lost since the functions simply return NULL on error. This makes
debugging harder, since a debug-enabled build is required to discover
the root cause of the error.
Fix by returning a status code from these functions, thereby allowing
any underlying errors to be propagated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Report errors in eoib_duplicate() via netdev_tx_err() rather than
netdev_tx_complete_err(), since netdev_tx_complete_err() accepts only
valid I/O buffers that are currently in the network device's transmit
queue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently request cable detection in PXE_OPCODE_INITIALIZE to work
around buggy Emulex drivers (see commit c0b61ba ("[efi] Work around
bugs in Emulex NII driver")).
This causes problems with some other NII drivers (e.g. Mellanox),
which may time out if the underlying link is intrinsically slow to
come up.
Attempt to work around both problems simultaneously by requesting
cable detection only if the underlying NII driver does not support
link status reporting via PXE_OPCODE_GET_STATUS. (This is based on a
potentially incorrect assumption that the buggy Emulex drivers do not
claim to report link status via PXE_OPCODE_GET_STATUS.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several files define the ARRAY_SIZE() macro as used in Linux. Provide
a common definition for this in include/compiler.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some VF data is not cleared with reset, so make sure to return all the
settings to default before configuring the VF.
This fixes an issue where network packets would fail to be received if
the VF was previously used by the linux ixgbevf driver.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to ThunderX Errata G-17560, NIC_PF_CFG[ENA] bit should not
be cleared at exit. This allows other drivers to access the NIC regs
correctly.
Signed-off-by: Konrad Adamczyk <konrad.adamczyk@cavium.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It is required to reset BGX context state for the LMAC using
BGX_CMR_CONFIG register.
This solves problem with network connectivity in Linux booted from
iPXE.
Signed-off-by: Bartosz Szczepanek <bartosz.szczepanek@cavium.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Originally-implemented-by: Malte zu Klampen <malte@pclab.ifg.uni-kiel.de>
Originally-implemented-by: Richard Moore <rich@richud.com>
Tested-by: Esben Storgaard Nielsen <esn@solar.dk>
Signed-off-by: Christian Nilsson <nikize@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the active timer (providing udelay() and currticks()) to be
selected at runtime based on probing during the INIT_EARLY stage of
initialisation.
TICKS_PER_SEC is now a fixed compile-time constant for all builds, and
is independent of the underlying clock tick rate. We choose the value
1024 to allow multiplications and divisions on seconds to be converted
to bit shifts.
TICKS_PER_MS is defined as 1, allowing multiplications and divisions
on milliseconds to be omitted entirely. The 2% inaccuracy in this
definition is negligible when using the standard BIOS timer (running
at around 18.2Hz).
TIMER_RDTSC now checks for a constant TSC before claiming to be a
usable timer. (This timer can be tested in KVM via the command-line
option "-cpu host,+invtsc".)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some host implementations (notably Google Compute Platform) are known
to unconditionally write back VIRTIO_NET_HDR_F_DATA_VALID to
header->flags for received packets, regardless of the features
negotiated by the driver. This breaks the transmit datapath by
effectively setting an illegal flag for all subsequent transmitted
packets.
Work around this problem by using separate empty header buffers for
the receive and transmit queues.
Debugged-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Virtio 0.9 implementation was limited to the maximum virtqueue size of
MAX_QUEUE_NUM and the virtio-net driver would fail to initialize on hosts
exceeding this limit.
This commit lifts the restriction by allocating the queue memory based on
the actual queue size instead of using a fixed maximum. Note that virtio
1.0 still uses the MAX_QUEUE_NUM constant to cap the size (unfortunately
this functionality is not available in virtio 0.9).
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This commit introduces virtnet_free_virtqueues called on all virtqueue
error and shutdown paths. vpm_find_vqs no longer cleans up after itself
and instead expects virtnet_free_virtqueues to be always called to undo
its effect.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit db34436 ("[intel] Strip spurious VLAN tags received by virtual
function NICs") accidentally introduced two copies of the
intel[x]vf_mbox_queues() function. Remove the unintended copy.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function may be configured to transparently insert a VLAN
tag into all transmitted packets. Unfortunately, it does not
equivalently strip this same VLAN tag from all received packets. This
behaviour may be observed in some Amazon EC2 instances with Enhanced
Networking enabled: transmissions work as expected but all packets
received by iPXE appear to have a spurious VLAN tag.
We can configure the receive queue to strip VLAN tags via the
RXDCTL.VME bit. We need to find out from the PF driver whether or not
we should do so.
There exists a "get queue configuration" mailbox message which
contains a field labelled IXGBE_VF_TRANS_VLAN in the Linux driver.
A comment in the Linux PF driver describes this field as "notify VF of
need for VLAN tag stripping, and correct queue". It will be filled
with a non-zero value if the PF is enforcing the use of a single VLAN
tag. It will also be filled with a non-zero value if the PF is using
multiple traffic classes.
The Linux VF driver seems to treat this field as being simply the
number of traffic classes, and gives it no VLAN-related
interpretation. The Linux VF driver instead handles the VLAN tag
stripping by simply assuming that any unrecognised VLAN tag ought to
be silently dropped.
We choose to strip and ignore the VLAN tag if the IXGBE_VF_TRANS_VLAN
field has a non-zero value.
Reported-by: Leonid Vasetsky <leonidv@velostrata.com>
Tested-by: Leonid Vasetsky <leonidv@velostrata.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ARM64 has a weaker memory order model than x86. The missing memory
barrier caused phy initialization notification to be delayed beyond
the link-wait timeout (15 secs).
Signed-off-by: Leendert van Doorn <leendert@paramecium.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Extend the 16-bit PCI bus:dev.fn address to a 32-bit seg🚌dev.fn
address, assuming a segment value of zero in contexts where multiple
segments are unsupported by the underlying data structures (e.g. in
the iBFT or BOFM tables).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This backport is from linux kernel upstream commit 83d6f1f ("ath9k:
fix buffer overrun for ar9287").
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification requires the EFI_SIMPLE_NETWORK_PROTOCOL
GetStatus() method to set TxBuf to NULL if there are no transmit
buffers to recycle.
Some implementations (observed with Lan9118Dxe in EDK2) fill in TxBuf
only when there is a transmit buffer to recycle, which leads to large
numbers of "spurious TX completion" errors.
Work around this problem by initialising TxBuf to NULL before calling
the GetStatus() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 86f96a4 ("[tg3] Remove x86-specific inline assembly")
introduced a regression in _tg3_flag() in 64-bit builds, since any
flags in the upper 32 bits of a 64-bit unsigned long would be
discarded when truncating to a 32-bit int.
Debugged-by: Shane Thompson <shane.thompson@aeontech.com.au>
Tested-by: Shane Thompson <shane.thompson@aeontech.com.au>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This commit makes virtio-net support devices with VEN 0x1af4 and DEV
0x1041, which is how non-transitional (modern-only) virtio-net devices
are exposed on the PCI bus.
Transitional devices supporting both the old 0.9.5 and new 1.0 version
of the virtio spec are driven using the new protocol. Legacy devices
are driven using the old protocol, same as before this commit.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This commit adds support for driving virtio 1.0 PCI devices. In
addition to various helpers, a number of vpm_ functions are introduced
to be used instead of their legacy vp_ counterparts when accessing
virtio 1.0 (aka modern) devices.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Virtio 1.0 introduces new constants and data structures, common to all
devices as well as specific to virtio-net. This commit adds a subset
of these to be able to drive the virtio-net 1.0 network device.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some EoIB implementations utilise an EoIB-to-Ethernet gateway device
that does not perform a FullMember join to the multicast group for the
EoIB broadcast domain. This has various exciting side-effects, such
as requiring every EoIB node to send every broadcast packet twice.
As an added bonus, the gateway may also break the EoIB MAC address to
GID mapping protocol by sending Ethernet-sourced packets from the
wrong QPN.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some EoIB implementations require each individual EoIB node to create
the multicast group for the EoIB broadcast domain.
It is left as an exercise for the interested reader to determine how
such an implementation might ever allow the parameters of such a
multicast group to be changed without requiring a simultaneous upgrade
of every driver on every operating system on every machine currently
attached to the fabric.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some EoIB implementations transmit a vendor-proprietary heartbeat
packet on the same multicast group used to provide the EoIB broadcast
domain.
Silently ignore these heartbeat packets, to avoid cluttering up the
network interface error statistics.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EoIB is a fairly simple protocol in which raw Ethernet frames
(excluding the CRC) are encapsulated within Infiniband Unreliable
Datagrams, with a four-byte fixed EoIB header (which conveys no actual
information). The Ethernet broadcast domain is provided by a
multicast group, similar to the IPoIB IPv4 multicast group.
The mapping from Ethernet MAC addresses to Infiniband address vectors
is achieved by snooping incoming traffic and building a peer cache
which can then be used to map a MAC address into a port GID. The
address vector is completed using a path record lookup, as for IPoIB.
Note that this requires every packet to include a GRH.
Add basic support for EoIB devices. This driver is substantially
derived from the IPoIB driver. There is currently no mechanism for
automatically creating EoIB devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit e62e52b ("[ipoib] Simplify test for received broadcast
packets") relies upon the multicast LID being present in the
destination address vector as passed to ipoib_complete_recv().
Unfortunately, this information is not present in many Infiniband
devices' completion queue entries.
Fix by testing instead for the presence of a multicast GID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ath_rx_init() demonstrates some serious confusion over how to use
pointers, resulting in (uint32_t*)NULL being used as a temporary
variable. This does not end well.
The broken code in question is performing manual alignment of I/O
buffers, which can now be achieved more simply using alloc_iob_raw().
Fix by removing ath_rxbuf_alloc() entirely.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some protocols (such as ARP) may modify the received packet and re-use
the same I/O buffer for transmission of a reply. The SMSC95XX
transmit header is larger than the receive header: the re-used I/O
buffer therefore does not have sufficient headroom for the transmit
header, and the ARP reply will therefore fail to be transmitted. This
is essentially the same problem as in commit 2e72d10 ("[ncm] Reserve
headroom in received packets").
Fix by reserving sufficient space at the start of each received packet
to allow for the difference between the lengths of the transmit and
receive headers.
This problem is not caught by the current driver development test
suite (documented at http://ipxe.org/dev/driver), since even the large
file transfer tests tend to completely sufficiently quickly that there
is no need for the server to ever send an ARP request. The failure
shows up only when using a very slow protocol such as RFC7440-enhanced
TFTP (as used by Windows Deployment Services).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The LED pins are configured by default as GPIO inputs. While it is
conceivable that a board might actually use these pins as GPIOs, no
such board is known to exist.
The Linux smsc95xx driver configures these pins unconditionally as LED
outputs. Assume that it is safe to do likewise.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The SMSC95xx devices tend to be used in embedded systems with a
variety of ad-hoc mechanisms for storing the MAC address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Tested using QEMU and usbredir to expose the LAN9512 chip present on a
Raspberry Pi.
There is a known issue with the LAN9512: an extra two bytes are
appended to every transmitted packet. These two bytes comprise:
{ 0x00, 0x08 } if packet length == 0 (mod 8)
{ CRC[0], 0x00 } if packet length == 7 (mod 8)
{ CRC[0], CRC[1] } otherwise
The extra bytes are appended whether the Ethernet CRC is generated
manually or added automatically by the hardware. The issue occurs
with the Linux kernel driver as well as the iPXE driver. It appears
to be an undocumented hardware errata.
TCP/IP traffic is not affected, since the IP header length field
causes the extraneous bytes to be discarded by the receiver. However,
protocols that rely on the length of the Ethernet frame (such as FCoE
or iPXE's "lotest" protocol) will be unusable on this hardware.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some models (notably ICH), the PHY reset mechanism appears to be
broken. In particular, the PHY_CTRL register will be correctly loaded
from NVM but the values will not be propagated to the "OEM bits" PHY
register. This typically has the effect of dropping the link speed to
10Mbps.
Since the original version of this driver in commit 945e428 ("[intel]
Replace driver for Intel Gigabit NICs"), we have always worked around
this problem by skipping the PHY reset if the link is already up.
Enhance this workaround by explicitly checking for known-broken PCI
IDs.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Make the class ID a property of the USB driver (rather than a property
of the USB device ID), and allow USB drivers to specify a wildcard ID
for any of the three component IDs (class, subclass, or protocol).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generate a score for each possible USB device configuration based on
the available driver support, and select the configuration with the
highest score. This will allow us to prefer ECM over RNDIS (for
devices which support both) and will allow us to meaningfully select a
configuration even when we have drivers available for all functions
(e.g. when exposing unused functions via EFI_USB_IO_PROTOCOL).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The raw EFI_HANDLE value is almost never useful to know, and simply
adds noise to the already verbose debug messages. Improve the
legibility of debug messages by using only the name generated by
efi_handle_name().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Infiniband link status change callback ipoib_link_state_changed()
may be called while the IPoIB device is closed, in which case there
will not be an IPoIB queue pair to be joined to the IPv4 broadcast
group. This leads to NULL pointer dereferences in ib_mcast_attach()
and ib_mcast_detach().
Fix by not attempting to join (or leave) the broadcast group unless we
actually have an IPoIB queue pair.
Signed-off-by: Wissam Shoukair <wissams@mellanox.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Multicast MAC addresses will never have REMAC cache entries, and the
corresponding multicast IPoIB MAC address cannot be obtained simply by
issuing an ARP request.
For the trivial volume of multicast packets that we expect to send in
any realistic scenario, the simplest solution is to send them as
broadcasts instead.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The only way to map an eIPoIB MAC address (REMAC) to an IPoIB MAC
address is to intercept an incoming ARP request or reply.
If we do not have an REMAC cache entry for a particular destination
MAC address, then we cannot transmit the packet. This can arise in at
least two situations:
- An external program (e.g. a PXE NBP using the UNDI API) may attempt
to transmit to a destination MAC address that has been obtained by
some method other than ARP.
- Memory pressure may have caused REMAC cache entries to be
discarded. This is fairly likely on a busy network, since REMAC
cache entries are created for all received (broadcast) ARP
requests. (We can't sensibly avoid creating these cache entries,
since they are required in order to send an ARP reply, and when we
are being used via the UNDI API we may have no knowledge of which
IP addresses are "ours".)
Attempt to ameliorate the situation by generating a semi-spurious ARP
request whenever we find a missing REMAC cache entry. This will
hopefully trigger an ARP reply, which would then provide us with the
information required to populate the REMAC cache.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As with the neighbour cache, discarding an REMAC cache entry is
potentially very disruptive.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When jumbo frames are enabled, the Linux ixgbe physical function
driver will disable the virtual function's receive datapath by
default, and will enable it only if the virtual function negotiates
API version 1.1 (or higher) and explicitly selects an MTU.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Virtual functions use a mailbox to communicate with the physical
function driver: this covers functionality such as obtaining the MAC
address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Intel virtual function NICs almost work with the use of "legacy"
transmit and receive descriptors (which are backwards compatible right
back to the original Intel Gigabit NICs).
Unfortunately the "TX switching" feature (which allows for VM<->VM
traffic to be looped back within the NIC itself) does not work when a
legacy TX descriptor is used: the packet is instead sent onto the
wire.
Fix by allowing for the use of an "advanced" TX descriptor (containing
exactly the same information as is found in the "legacy" descriptor).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current API for Base16 (and Base64) encoding requires the caller
to always provide sufficient buffer space. This prevents the use of
the generic encoding/decoding functionality in some situations, such
as in formatting the hex setting types.
Implement a generic hex_encode() (based on the existing
format_hex_setting()), implement base16_encode() and base16_decode()
in terms of the more generic hex_encode() and hex_decode(), and update
all callers to provide the additional buffer length parameter.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This changed in Linux kernel the same way in commit 7067e701
("ath9k_hw: remove confusing logic inversion in an ANI variable") by
Felix Fietkau.
Additionally this fixes "error: logical not is only applied to the
left hand side of comparison" with GCC 5.1.0.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
I218-LM (rev 3) is found in Lenovo Thinkpad X250. The remaining
device IDs are from linux/drivers/net/ethernet/intel/e1000e/hw.h
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some RTL8169 onboard NICs (observed with a Lenovo ThinkPad 11e),
the EEPROM is not merely not present: any attempt to read from the
non-existent EEPROM will crash and reboot the system.
The equivalent code to read from the EEPROM was removed from the Linux
r8169 driver in 2009 with a comment suggesting that it was similarly
found to be unreliable on some systems.
Fix by accessing the EEPROM only on RTL8139 NICs, and assuming that
the MAC address will always be correctly preset on RTL8169 NICs.
Reported-by: Evan Prohaska <eprohaska@edkey.org>
Tested-by: Evan Prohaska <eprohaska@edkey.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The emulated Intel 82545em in some versions of VMware (observed with
ESXi v5.1) seems to sometimes fail to set the RXT0 bit in the
interrupt cause register (ICR), causing iPXE to stop receiving
packets. Work around this problem (for the 82545em only) by always
polling the receive queue regardless of the state of the ICR.
Reported-by: Slava Bendersky <volga629@networklab.ca>
Tested-by: Slava Bendersky <volga629@networklab.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At least one NII implementation (in a Microsoft Surface tablet) seems
to fail to report the absence (sic) of TX completions properly. Work
around this by checking for TX completions only when we expect to see
one.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some NII implementations will fail the GET_STATUS operation if we
request the media status. Fix by doing so only if GET_INIT_INFO
reported that media status is supported.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RX FIFO overflow is almost inevitable since the (usable) USB2 bus
bandwidth is approximately one quarter of the Ethernet bandwidth.
Avoid flooding the console with RX FIFO overflow messages in a
standard debug build.
With TCP SACK implemented, the RX FIFO overflow no longer causes a
catastrophic drop in throughput. Experimentation shows that HTTP
downloads now progress at a fairly smooth 250Mbps, which is around the
maximum speed attainable for a USB2 NIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This driver is functional but any downloads via a TCP-based protocol
tend to perform poorly. The 1Gbps Ethernet line rate is substantially
higher than the 480Mbps (in practice around 280Mbps) provided by USB2,
and the device has only 32kB of internal buffer memory. Our 256kB TCP
receive window therefore rapidly overflows the RX FIFO, leading to
multiple dropped packets (usually within the same TCP window) and
hence a low overall throughput.
Reducing the TCP window size so that the RX FIFO does not overflow
greatly increases throughput, but is not a general-purpose solution.
Further investigation is required to determine how other OSes
(e.g. Linux) cope with this scenario. It is possible that
implementing TCP SACK would provide some benefit.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most devices expose at least the link up/down status via a bit in a
MAC register, since the MAC generally already needs to know whether or
not the link is up. Some devices (e.g. the SMSC75xx USB NIC) expose
this information to software only via the MII registers.
Provide a generic mii_check_link() implementation to check the BMSR
and report the link status via netdev_link_{up,down}().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE already sends RX notifications to the backend when needed, but
does not set the "feature-rx-notify" flag. As of XenServer 6.5, this
flag is mandatory and omitting it will cause the backend to fail.
Fix by setting the "feature-rx-notify" flag, to inform the backend
that we will send notifications.
Reported-by: Shalom Bhooshi <shalom.bhooshi@citrix.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Relicense files with kind permission from
Stefan Hajnoczi <stefanha@redhat.com>
alongside the contributors who have already granted such relicensing
permission.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At some point in the past few years, binutils became more aggressive
at removing unused symbols. To function as a symbol requirement, a
relocation record must now be in a section marked with @progbits and
must not be in a section which gets discarded during the link (either
via --gc-sections or via /DISCARD/).
Update REQUIRE_SYMBOL() to generate relocation records meeting these
criteria. To minimise the impact upon the final binary size, we use
existing symbols (specified via the REQUIRING_SYMBOL() macro) as the
relocation targets where possible. We use R_386_NONE or R_X86_64_NONE
relocation types to prevent any actual unwanted relocation taking
place. Where no suitable symbol exists for REQUIRING_SYMBOL() (such
as in config.c), the macro PROVIDE_REQUIRING_SYMBOL() can be used to
generate a one-byte-long symbol to act as the relocation target.
If there are versions of binutils for which this approach fails, then
the fallback will probably involve killing off REQUEST_SYMBOL(),
redefining REQUIRE_SYMBOL() to use the current definition of
REQUEST_SYMBOL(), and postprocessing the linked ELF file with
something along the lines of "nm -u | wc -l" to check that there are
no undefined symbols remaining.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the standard warranty disclaimer and Free Software Foundation
address paragraphs to the licence text where these are not currently
present.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some USB endpoints require that a short packet be used to terminate
transfers, since they have no other way to determine message
boundaries. If the message length happens to be an exact multiple of
the USB packet size, then this requires the use of an additional
zero-length packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some protocols (such as ARP) may modify the received packet and re-use
the same I/O buffer for transmission of a reply. To allow this,
reserve sufficient headroom at the start of each received packet
buffer for our transmit datapath headers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some devices have a very small number of internal buffers, and rely on
being able to pack multiple packets into each buffer. Using 2048-byte
buffers on such devices produces throughput of around 100Mbps. Using
a small number of much larger buffers (e.g. 32kB) increases the
throughput to around 780Mbps. (The full 1Gbps is not reached because
the high RTT induced by the use of multi-packet buffers causes us to
saturate our 256kB TCP window.)
Since allocation of large buffers is very likely to fail, allocate the
buffer set only once when the device is opened and recycle buffers
immediately after use. Received data is now always copied to
per-packet buffers.
If allocation of large buffers fails, fall back to allocating a larger
number of smaller buffers. This will give reduced performance, but
the device will at least still be functional.
Share code between the interrupt and bulk IN endpoint handlers, since
the buffer handling is now very similar.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The (undocumented) VMBus protocol seems to allow for transfer
page-based packets where the data payload is split into an arbitrary
set of ranges within the transfer page set.
The RNDIS protocol includes a length field within the header of each
message, and it is known from observation that multiple RNDIS messages
can be concatenated into a single VMBus message.
iPXE currently assumes that the transfer page range boundaries are
entirely arbitrary, and uses the RNDIS header length to determine the
RNDIS message boundaries.
Windows Server 2012 R2 generates an RNDIS_INDICATE_STATUS_MSG for an
undocumented and unknown status code (0x40020006) with a malformed
RNDIS header length: the length does not cover the StatusBuffer
portion of the message. This causes iPXE to report a malformed RNDIS
message and to discard any further RNDIS messages within the same
VMBus message.
The Linux Hyper-V driver assumes that the transfer page range
boundaries correspond to RNDIS message boundaries, and so does not
notice the malformed length field in the RNDIS header.
Match the behaviour of the Linux Hyper-V driver: assume that the
transfer page range boundaries correspond to the RNDIS message
boundaries and ignore the RNDIS header length. This avoids triggering
the "malformed packet" error and also avoids unnecessary data copying:
since we now have one I/O buffer per RNDIS message, there is no longer
any need to use iob_split().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Empirical observation suggests that 32 is a sensible size to minimise
the number of deferred packet transmissions without overflowing the
VMBus transmit ring buffer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for elision of transmitted TCP ACKs by handling all received
VMBus messages in each network device poll operation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On Windows Server 2012 R2, the receive buffer teardown completion
message seems to occasionally be deferred until after the VMBus
channel has been closed. This happens even if there are no packets
currently in the receive buffer.
Work around this problem by separating the revocation and teardown of
the receive buffer, and deferring the teardown until after the VMBus
channel has been closed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The i350 (and possibly other Intel NICs) have a non-trivial
correspondence between the PCI function number and the external
physical port number. For example, the i350 has a "LAN Function Sel"
bit within the EEPROM which can invert the mapping so that function 0
becomes port 3, function 1 becomes port 2, etc.
Unfortunately the MAC addresses within the EEPROM are indexed by
physical port number rather than PCI function number. The end result
is that when anything other than the default mapping is used, iPXE
will use the wrong address as the base MAC address.
Fix by using the autoloaded MAC address if it is valid, and falling
back to reading the MAC address directly from the EEPROM only if no
autoloaded address is available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
End users almost certainly don't care whether the underlying interface
is SNP or NII/UNDI. Try to minimise surprise and unnecessary
documentation by including the NII driver whenever the SNP driver is
requested.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE itself exposes a dummy NII protocol with no UNDI. Avoid
potentially dereferencing a NULL pointer by checking for a non-zero
UNDI address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some UEFI network drivers provide a software UNDI interface which is
exposed via the Network Interface Identifier Protocol (NII), rather
than providing a Simple Network Protocol (SNP).
The UEFI platform firmware will usually include the SnpDxe driver,
which attaches to NII and provides an SNP interface. The SNP
interface is usually provided on the same handle as the underlying NII
device. This causes problems for our EFI driver model: when
efi_driver_connect() detaches existing drivers from the handle it will
cause the SNP interface to be uninstalled, and so our SNP driver will
not be able to attach to the handle. The platform firmware will
eventually reattach the SnpDxe driver and may attach us to the SNP
handle, but we have no way to prevent other drivers from attaching
first.
Fix by providing a driver which can attach directly to the NII
protocol, using the software UNDI interface to drive the network
device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The snpnet driver uses netdev_tx_defer() and so must ensure that space
in the (single-entry) transmit descriptor ring is freed up before
calling netdev_tx_complete().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the ID for the LM variant and differentiate it from the I217-V.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently require information about the underlying PCI device to
populate the snpnet device's name and description. If the underlying
device is not a PCI device, this will fail and prevent the device from
being registered.
Fix by falling back to populating the device description with
information based on the EFI handle, if no PCI device information is
available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some systems will install a child of the SNP device and use this as
our loaded image's device handle, duplicating the installation of the
underlying SNP protocol onto the child device handle. On such
systems, we want to end up driving the parent device (and
disconnecting any other drivers, such as MNP, which may be attached to
the parent device).
Fix by recording the SNP protocol instance at initialisation time, and
using this to match against device handles (rather than simply
comparing the handles themselves).
Reported-by: Jarrod Johnson <jarrod.b.johnson@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ICH8 devices have an errata which requires us to reconfigure the
packet buffer size (PBS) register, and correspondingly adjust the
packet buffer allocation (PBA) register. The "Intel I/O Controller
Hub ICH8/9/10 and 82566/82567/82562V Software Developer's Manual"
notes for the PBS register that:
10.4.20 Packet Buffer Size - PBS (01008h; R/W)
Note: The default setting of this register is 20 KB and is
incorrect. This register must be programmed to 16 KB.
Initial value: 0014h
0018h (ICH9/ICH10)
It is unclear from this comment precisely which devices require the
workaround to be applied. We currently attempt to err on the side of
caution: if we detect an initial value of either 0x14 or 0x18 then the
workaround will be applied. If the workaround is applied
unnecessarily, then the effect should be just that we use less than
the full amount of the available packet buffer memory.
Unfortunately this approach does not play nicely with other device
drivers. For example, the Linux e1000e driver will rewrite PBA while
assuming that PBS still contains the default value, which can result
in inconsistent values between the two registers, and a corresponding
inability to transmit or receive packets. Even more unfortunately,
the contents of PBS and PBA are not reset by anything less than a
power cycle, meaning that this error condition will survive a hardware
reset.
The Linux driver (written and maintained by Intel) applies the PBS/PBA
errata workaround only for devices in the ICH8 family, identified via
the PCI device ID. Adopt a similar approach, using the PCI_ROM()
driver data field to indicate when the workaround is required.
Reported-by: Donald Bindner <dbindner@truman.edu>
Debugged-by: Donald Bindner <dbindner@truman.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Under some circumstances (e.g. if iPXE itself is booted via iSCSI, or
after an unclean reboot), the backend may not be in the expected
InitWait state when iPXE starts up.
There is no generic reset mechanism for Xenbus devices. Recent
versions of xen-netback will gracefully perform all of the required
steps if the frontend sets its state to Initialising. Older versions
(such as that found in XenServer 6.2.0) require the frontend to
transition through Closed before reaching Initialising.
Add a reset mechanism for netfront devices which does the following:
- read current backend state
- if backend state is anything other than InitWait, then set the
frontend state to Closed and wait for the backend to also reach
Closed
- set the frontend state to Initialising and wait for the backend to
reach InitWait.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using version 1 grant tables limits guests to using 16TB of grantable
RAM, and prevents the use of subpage grants. Some versions of the Xen
hypervisor refuse to allow the grant table version to be set after the
first grant references have been created, so the loaded operating
system may be stuck with whatever choice we make here. We therefore
currently use version 2 grant tables, since they give the most
flexibility to the loaded OS.
Current versions (7.2.0) of the Windows PV drivers have no support for
version 2 grant tables, and will merrily create version 1 entries in
what the hypervisor believes to be a version 2 table. This causes
some confusion.
Avoid this problem by attempting to use version 1 tables, since
otherwise we may render Windows unable to boot.
Play nicely with other potential bootloaders by accepting either
version 1 or version 2 grant tables (if we are unable to set our
requested version).
Note that the use of version 1 tables on a 64-bit system introduces a
possible failure path in which a frame number cannot fit into the
32-bit field within the v1 structure. This in turn introduces
additional failure paths into netfront_transmit() and
netfront_refill_rx().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The behavior observed in the Apple EFI (1.10) RecieveFilters() call
is:
- failure if any of the PROMISCUOUS or MULTICAST filters are
included
- success if only UNICAST is included, however the result is
UNICAST|BROADCAST
- success if only UNICAST and BROADCAST are included
- if UNICAST, or UNICAST|BROADCAST are used, but the previous call
tried (and failed) to set UNICAST|BROADCAST|MULTICAST, then the
result is UNICAST|BROADCAST|MULTICAST
Work around this apparently broken SNP implementation by trying
RecieveFilterMask, then falling back to UNICAST|BROADCAST|MULTICAST,
then UNICAST|BROADCAST, and finally UNICAST.
Modified-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Curtis Larsen <larsen@dixie.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some EFI 1.10 systems (observed on an Apple iMac) do not allow us to
open the device path protocol with an attribute of
EFI_OPEN_PROTOCOL_BY_DRIVER and so we cannot maintain a safe,
long-lived pointer to the device path. Work around this by instead
opening the device path protocol with an attribute of
EFI_OPEN_PROTOCOL_GET_PROTOCOL whenever we need to use it.
Debugged-by: Curtis Larsen <larsen@dixie.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to the UEFI specification, the MCastFilter parameter (which
we currently pass as NULL, along with a zero MCastFilterCnt) is
optional only if ResetMCastFilter is true.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Dump the existing openers of a protocol whenever we are unable to open
a protocol using attributes of BY_DEVICE, EXCLUSIVE, or
BY_CHILD_CONTROLLER.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using efi_devpath_text() is marginally more efficient if we already
have the device path protocol available, but the mild increase in
efficiency is not worth compromising the clarity of the pattern:
DBGC ( device, "THING %p %s ...", device, efi_handle_name ( device ) );
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rob Taglang
Michael Brown
Joseph Wong
Janos Mattyasovszky
Peter von Konigsmark
Richard Moore
Jason Wang
Jerone Young
Mika Tiainen
Martin Habets
Adamczyk, Konrad
Mike McCormack
Vishvananda Ishaya
Bartosz Szczepanek
Christian Nilsson
Ladi Prosek
Lukas Grossar
Leendert van Doorn
Christian Hesse
Hummel Frank
Torgeir Wulfsberg
Kyösti Mälkki
Carl Henrik Lunde
Fabrice Bacchella
Wissam Shoukair
Bernd Wiebelt
Ed Swierk
Laszlo Ersek
Thomas Miletich
Anton D. Kachalov
Jan Kiszka
Curtis Larsen