Practically speaking, it seems the convention is to only have one
packet pending and not rely upon any mechanism to associate returned
txbuf with txqueue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This function never did much in this driver anyway, and after commit
b5ed30b2 ("[tg3] Fix compilation on newer gcc versions") it became
apparent that its remaining functionality could be easily moved to
tg3_test_dma().
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old Etherboot tg3 driver with a more up-to-date driver
using the iPXE API.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RS bit is used to instruct the NIC to update the TX descriptor
status byte. The RPS bit is used to instruct the NIC to defer this
update until after the packet has been transmitted on the wire (rather
than merely read into the transmit FIFO).
The driver currently sets RPS but not RS. Some e1000 models seem to
interpret this as implying that the status byte should be updated;
some don't. On the ones that don't, we never see any TX completions
and so rapidly run out of TX buffers.
Fix by setting the RS bit in the TX descriptor. (We don't care about
when the packet reaches the wire, so don't bother setting the RPS
bit.)
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
WinPE has been observed to call PXENV_UNDI_SHUTDOWN but not
PXENV_STOP_UNDI. This means that Hermon hardware is left partially
active (firmware running and one event queue mapped) when WinPE starts
up, which can cause a Blue Screen of Death.
Fix by ensuring that the hardware is left quiescent (with the firmware
stopped) when no interfaces are open.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid spurious matches for peer key 0 against empty peer cache
entries, and set the LL_MULTICAST flag in addition to LL_BROADCAST.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ChipCmd register is only an 8-bit register. The 16-bit access
used by iPXE was causing an issue when used with qemu emulated rtl8139
device which was improperly aligning IOs.
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Arbel seems to crash the system as soon as the first send WQE
completes on an RC queue pair. (NOPs complete successfully, so this
is a problem specific to the work queue rather than the completion
queue.) The cause of this problem has remained unknown for over a
year.
Check in the non-functioning code to avoid bit-rot, and in the hope
that someone will find the fix.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reported-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This reverts commit 15c1200 ("[hermon] Work around missing mport
support in current BOFM implementations").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Current BOFM versions are unable to create entries with mport>1, which
means that only the port 1 MAC address can be explicitly specified.
Work around this by using the provided MAC address as a base address
for all subsequent ports. For example, if BOFM assigns the address
00:1A:64:76:00:09 for port 1
then we will assign the addresses
00:1A:64:76:00:09 for port 1
00:1A:64:76:00:0a for port 2
Future BOFM versions that may correctly support mport will work with
this scheme without modification provided that the BOFM entries are
created in increasing order of mport. Since BOFM tools tend to
generate entries in increasing order (of slot, port, etc), this is not
an unreasonable compromise.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE operates the forcedeth NIC in promiscuous mode, and never changes
the unicast MAC address filter registers. We should not therefore set
the flag indicating (to other drivers loaded later) that the MAC
address order has already been corrected.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The forcedeth driver currently implements unicast MAC address
filtering in software. This is almost invariably the wrong thing to
do (since the network stack must already be able to cope with unwanted
packets) and it breaks FCoE (which requires the card to operate in
promiscuous mode).
Also, the implementation is buggy: is_local_ether_addr() is used to
check for a locally-assigned Ethernet address (not to check for a
unicast address), and the current link-layer address is in
netdev->ll_addr, not netdev->hw_addr.
Fix by removing this code.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid unused-but-set variable warning in gcc 4.6 which was introduced
by commit 9215b7f ("[forcedeth] Clear the MII link status register on
link status changes").
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose a function setting_applies() to allow a caller to determine
whether or not a particular setting is applicable to a particular
settings block.
Restrict DHCP-backed settings blocks to accepting only DHCP-based
settings.
Restrict network device settings blocks to accepting only DHCP-based
settings and network device-specific settings such as "mac".
Inspired-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
From a cursory examination, it appears as though the calculation of
tx_available is redundant, since eepro_transmit() waits for transmit
completion before returning anyway.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On reset and close, the ICR register is read to clear any pending
interrupts, but the value is simply ignored. Avoid assigning the
value to a variable, to inhibit a warning from gcc 4.6.
Also fix a potential race condition in reset routines which clear
interrupts before disabling them.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
These unused portions trigger a compiler warning under gcc 4.6, due to
the ambiguity over the "page" field in struct igbvf_buffer.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a virtual environment such as qemu, we can legitimately receive
packets less than 64 bytes in length, such as ARP replies. These are
currently discarded, causing most IPv4 communication to fail.
Fix by ignoring the RFDShort bit when receiving packets.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading rtl8139.pxe from an old Etherboot rtl8139.zrom, iPXE
can end up misreading the first word of the MAC address from the
EEPROM as being all zeroes. This is presumably because Etherboot has
left the serial EEPROM in an unexpected state.
Fix by using the chip select line to reset the SPI device before we
start accessing it.
Reported-by: Mandar U Jog <mandarjog@gmail.com>
Tested-by: Mandar U Jog <mandarjog@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default initiator IQN is "iqn.2000-09.org.etherboot:UNKNOWN".
This is problematic for two reasons:
a) the etherboot.org domain (and hence the associated IQN namespace)
is not under the control of the iPXE project, and
b) some targets (correctly) refuse to allow concurrent connections
from different initiators using the same initiator IQN.
Solve both problems by changing the default initiator IQN to be
iqn.2010-04.org.ipxe:<hostname> if a hostname is set, or
iqn.2010-04.org.ipxe:<uuid> if no hostname is set.
Explicit initiator IQNs set via DHCP option 203 are not affected by
this change.
Unfortunately, this change is likely to break some existing
configurations, where ACL rules have been put in place referring to
the old default initiator IQN. Users may need to update ACLs, or
force the use of the old IQN using an iPXE script line such as
set initiator-iqn iqn.2000-09.org.etherboot:UNKNOWN
or a dhcpd.conf option such as
option iscsi-initiator-iqn "iqn.2000-09.org.etherboot:UNKNOWN"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some operating environments require (or at least prefer) that we do
not perform our own PCI bus scan, but deal only with specified
devices. Modularise the PCI core to allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge the "bus" and "devfn" fields into a single "busdevfn" field, to
match the format used by the majority of external code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 64-bit builds, MLX_DECLARE_STRUCT() produces a structure that is
always a multiple of 64 bits long, causing the HCR structure to be
over-length by one dword. This in turn causes hermon_cmd() to write
beyond the end of the HCR, which causes commands to fail.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leak of untreated events by having circular event queue
operation.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove duplicate hardware resets, remove network interface logic
reset.
This also fixes a bug where some 3c905C variants would return bogus
EEPROM values because of a too short delay after the network reset.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DBG is reserved for errors and important warnings only.
DBG2 for additional information, e.g. "received packet".
DBGP is used to print the name of every function as it is called.
Signed-off-by: Thomas Miletich<thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the concept of shutdown exit flags, and replace it with a
counter used to keep track of exposed interfaces that require devices
to remain active.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support a new function mode "multi-function 8 Direct IO" which is used
in ESX Direct I/O configuration.
Update driver version to 3.5.0.1
Signed-off-by: Masroor Vettuparambil <masroor.vettuparambil@exar.com>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@exar.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most xxx_init() functions are void functions with no failure cases.
Allow pci_vpd_init() to be used in the same way. (Subsequent calls to
pci_vpd_read() etc. will fail if pci_vpd_init() fails.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since its implementation several years ago, no driver has used a
fragment list containing more than a single fragment. Simplify the
NVO core and the drivers that use it by removing the whole concept of
the fragment list, and using a simple (address,length) pair instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Driver for Intel 82576 based virtual functions, based on Intel source
code available at:
http://sourceforge.net/projects/e1000 (igbvf-1.0.7)
Based on initial port from Eric Keller <ekeller@princeton.edu>.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Changes were made to files where the licence text within the files
themselves confirms that the files are GPL version 2 or later.
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Pass the settings block name as a parameter to register_settings(),
rather than defining it with settings_init() (and then possibly
changing it by directly manipulating settings->name).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some SCSI targets (observed with an EMC CLARiiON Fibre Channel target)
will not respond to commands correctly until a TEST UNIT READY has
been issued. In particular, a READ CAPACITY (10) command will return
with a success status, but no capacity data.
Fix by issuing a TEST UNIT READY command automatically, and delaying
further SCSI commands until the TEST UNIT READY has succeeded.
Reported-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires us to be able to receive unicast packets for multiple
addresses. Support this by operating in promiscuous mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PRM structures to support Hermon Ethernet devices.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Unlike Arbel, port parameters must be applied via a separate call to
SET_PORT, rather than as parameters to INIT_PORT.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Mapping a single page at a time causes a several-second delay at
device initialisation time. Reduce this by mapping multiple pages at
a time, using the largest block sizes possible given the alignment
constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Mapping a single page at a time causes a several-second delay at
device initialisation time. Reduce this by mapping multiple pages at
a time, using the largest block sizes possible given the alignment
constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use individual page mappings rather than a single whole-region
mapping, to avoid the waste of memory that occurs due to the
constraint that each mapped block must be aligned on its own size.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Backport some changes from the Hermon driver to the Arbel driver.
Specifically:
o Rename reserved_lkey to lkey
o Add arbel_rate() to calculate transmission rates
o Structure code to allow for addition of RC queue pairs
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the amount of ICM space required by choosing to order the
various allocations in approximately descending order of alignment
requirements.
This saves approximately 512kB of host memory.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current method for ICM allocation exactly matches the addresses
chosen by the old Etherboot driver, but does not match the
specification. Some ICM tables (notably the queue pair context table)
therefore end up incorrectly aligned.
Fix by performing allocations as per the specification.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the utility of debugging messages by including the relevant
port number, queue number (QPN, CQN, EQN), work queue entry (WQE)
number, and physical addresses wherever applicable.
Add arbel_dump_cqctx() for dumping a completion queue context and
arbel_dump_qpctx() for dumping a queue pair context.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This is a backport of commit 0b1222f ("[hermon] Randomise the
high-order bits of queue pair numbers") to the Arbel driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This is a backport of commit cd5a213 ("[hermon] Allow software GMA to
receive packets destined for QP1") to the Arbel driver.
This patch includes a correction to a bug in the autogenerated
hardware description header file.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Only port state change events are currently mapped to our event queue,
since those are the only events we are prepared to handle. This
ignores a potentially useful source of diagnostic information in the
case of unexpected failures.
Fix by mapping all events to the event queue; a build with debugging
enabled will therefore at least dump the raw content of the unexpected
events.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Only port state change events are currently mapped to our event queue,
since those are the only events we are prepared to handle. This
ignores a potentially useful source of diagnostic information in the
case of unexpected failures.
Fix by mapping all events to the event queue; a build with debugging
enabled will therefore at least dump the raw content of the unexpected
events.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently uses the first port's port GUID as the node GUID,
rather than using the (possibly distinct) real node GUID. This can
confuse opensm during the handover to a loaded OS: it thinks the port
already belongs to a different node and so discards our port
information with a warning message about duplicate ports. Everything
is picked up correctly on the second subnet sweep, after opensm has
established that the "old" node no longer exists, but this can delay
link-up unnecessarily by several seconds.
Fix by using the real node GUID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No event is generated upon reaching INIT, so we must poll separately
for link state changes while we remain DOWN.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No event is generated upon reaching INIT, so we must poll separately
for link state changes while we remain DOWN.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ib_smc_update() potentially updates the Infiniband port state, and so
should almost always be followed by a call to ib_link_state_changed().
The one exception is the call made to ib_smc_update() before the
device is registered.
Fix by removing explicit calls to ib_link_state_changed() from drivers
using ib_smc_update(), including a call to ib_link_state_changed()
within ib_smc_update(), and creating a separate ib_smc_init() for use
prior to device registration.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The sense key gives a first idea of what the problem might be, and so
is potentially useful in diagnosing problems in a non-debug build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The block device interface used in gPXE predates the invention of even
the old gPXE data-transfer interface, let alone the current iPXE
generic asynchronous interface mechanism. Bring this old code up to
date, with the following benefits:
o Block device commands can be cancelled by the requestor. The INT 13
layer uses this to provide a global timeout on all INT 13 calls,
with the result that an unexpected passive failure mode (such as
an iSCSI target ACKing the request but never sending a response)
will lead to a timeout that gets reported back to the INT 13 user,
rather than simply freezing the system.
o INT 13,00 (reset drive) is now able to reset the underlying block
device. INT 13 users, such as DOS, that use INT 13,00 as a method
for error recovery now have a chance of recovering.
o All block device commands are tagged, with a numerical tag that
will show up in debugging output and in packet captures; this will
allow easier interpretation of bug reports that include both
sources of information.
o The extremely ugly hacks used to generate the boot firmware tables
have been eradicated and replaced with a generic acpi_describe()
method (exploiting the ability of iPXE interfaces to pass through
methods to an underlying interface). The ACPI tables are now
built in a shared data block within .bss16, rather than each
requiring dedicated space in .data16.
o The architecture-independent concept of a SAN device has been
exposed to the iPXE core through the sanboot API, which provides
calls to hook, unhook, boot, and describe SAN devices. This
allows for much more flexible usage patterns (such as hooking an
empty SAN device and then running an OS installer via TFTP).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Doorbell records are currently embedded within the completion queue
and receive work queue strucures, which are allocated using zalloc()
and so have an alignment guarantee of only sizeof(void*), i.e. four
bytes. This is sufficient for the receive work queue, but not for the
completion queue, which requires an alignment guarantee of eight
bytes.
Though not guaranteed, it so happens that zalloc() will always return
a pointer that is exactly four bytes above a sixteen-byte boundary.
The completion queue doorbell record is therefore always misaligned,
and the value passed to the hardware via SW2HW_CQ is actually always
pointing to the page_offset value within the MTT descriptor (which
directly precedes the inline doorbell record). Provided that the page
offset is greater than 0x100, this looks to the hardware like an
update_ci value of greater than 0x010000 (taking into account
endianness differences), and so the hardware will happily deliver more
than 0x010000 completions before stopping. Hence this problem is
rarely observable.
Fix by allocating the doorbell records separately and using the
correct alignment constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give completion queues a chance to deliver exception events by
programming in the number of our event queue (currently used only for
port state changes).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the utility of debugging messages by including the relevant
port number, queue number (QPN, CQN, EQN), work queue entry (WQE)
number, and physical addresses wherever applicable.
Add hermon_dump_cqctx() for dumping a completion queue context, and
hermon_fill_nop_send_wqe() for inserting NOPs into send work queues.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An attempt to transmit a packet of 8192 bytes or larger will collide
with the status bits in the TX descriptor. This gives the appearance
of the network card's transmit data path having just suddenly stopped
responding; iPXE is waiting for the card to report a TX completion
but, because of the status bit collision, the card thinks that the
descriptor has not yet been written.
Fix by explicitly checking for oversized packets in rtl_transmit().
Discovered during Fibre Channel over Ethernet testing, and debugged by
using gdb to examine the state of the emulated rtl8139 card in qemu.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the explicit calls from the Infiniband core to the IPoIB layer
with the general concept of an Infiniband upper-layer driver
(analogous to a PCI driver) which can create arbitrary devices on top
of Infiniband devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The rtl8139 driver includes the Ethernet CRC within the received
packet. All current protocols ignore trailing garbage, but FCoE
requires the frame length to be correct (since the FCoE footer
position is calculated from the end of the packet), so fix the driver
to strip out the CRC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PCI ID 8086:27dc to the eepro100 driver.
Reported-by: Cédric Delmas <c.delmas@akka.eu>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the tap driver that can be used like:
$ ./ipxe.linux --net tap,if=tap0,mac=00:0c:29:c5:39:a1
The if setting is mandatory.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the base to build linux drivers and the linux UI code on. UI
fills device requests, which are later walked over by the linux
root_driver and delegated to specific linux drivers.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
alloc_memblock() and free_memblock() are internal.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
pcbios specific get_memmap() is used by the b44 driver making
all-drivers builds fail on other platforms. Move it to the I/O API
group and provide a dummy implementation on EFI.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE forcedeth driver and removes the legacy
Etherboot forcedeth driver. It supports 40 different chips, compared
to the original 14.
It has been tested on a NIC with an CK804 Ethernet Controller, and the
results of downloading 5 100mb images in a row have been:
12/11/11/11/11 seconds; booting DSL using pxelinux also succeeded. The
driver has also been tested by chaining undionly.kpxe and it worked.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Tested-by: Andrei Faur <da3drus@gmail.com>
Tested-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE virtio-net driver and removes the legacy
Etherboot virtio-net driver. The main reasons for doing this are:
1. Multiple virtio-net NICs are now supported by iPXE. The legacy
driver kept global state and caused issues in virtual machines with
more than one virtio-net device.
2. Faster downloads. The native iPXE driver downloads 100 MB over
HTTP in 12s, the legacy Etherboot driver in 37s. This simple
benchmark uses KVM with tap networking and the Python
SimpleHTTPServer both running on the same host.
Changes to core virtio code reduce vring descriptors to 256 (QEMU uses
128 for virtio-blk and 256 for virtio-net) and change the opaque token
from u16 to void*. Lowering the descriptor count reduces memory
consumption. The void* opaque token change makes driver code simpler.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This bug caused .probe to fail because the NIC did not reset properly.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add NonVolatile Option (nvo) and NonVolatile Storage (nvs) support to
the myri10ge driver using the EEPROM read/write mechanism provided by
the NIC's Vendor Specific PCI capability.
The myri10ge NIC is capabile of storing 64KB or more of nonvolatile
options, but this patch advertises only 512 bytes of nvo storage
because iPXE malloc's a buffer matching the total size we advertise.
512 is plenty without wasting malloc'd memory. (The 2 other drivers
currently supporting nvo advertise 256 bytes or less.)
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch removes the cfg lookup made in the r8169 driver and
replaces it with equivalent information found in the driver_data field
of the pci_device_id structure.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove data-xfer as an interface type, and replace data-xfer
interfaces with generic interfaces supporting the data-xfer methods.
Filter interfaces (as used by the TLS layer) are handled using the
generic pass-through interface capability. A side-effect of this is
that deliver_raw() no longer exists as a data-xfer method. (In
practice this doesn't lose any efficiency, since there are no
instances within the current codebase where xfer_deliver_raw() is used
to pass data to an interface supporting the deliver_raw() method.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using ref_init() to initialise an embedded reference
count, to match the coding style used by other embedded objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch replaces the old pcnet32 driver with a new one that
uses iPXE's API.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
After changing the driver to refill after feed, if any error occurs a
non-contiguous empty buffer will be introduced in the ring due to my
reuse-buffer-when-error implementation.
Reported-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A new driver for JMicron Ethernet controller.
Reviewed-by: Joshua Oreman <oremanj@rwcr.net>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Reviewed-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a new network driver that consumes the EFI Simple Network
Protocol. Also add a bus driver that can find the Simple Network
Protocol that iPXE was loaded from; the resulting behavior is similar
to the "undionly" driver for BIOS systems.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Fix up the whitespace errors inadvertently introduced by the
last-minute rename from the internal QLogic codename to "qib7322".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Apart from format specifier fixes there are two changes in proper code:
- Change type of regs in skge_hw to unsigned long
- Cast result of sizeof in myri10ge to uint32_t
Both don't change anything for i386 and should be fine on x86_64.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Christopher Armenio reported link detection problems with an
integrated eepro100 NIC. Thomas Miletich removed link detection code
from the eepro100 driver and verified that the driver continued to
function. Christopher verified Thomas' patch on his integrated
eepro100 NIC.
Reported-by: Christopher Armenio <christopher.armenio@resquared.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
In building gpxe for openSUSE Factory (part of kvm package), there were
a few problems identified by the compiler. This patch addresses them.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The interrupt control mechanism on Phantom cards has changed
substantially since the driver was initially written. This updates
the code to match the mechanism used in production firmware.
This is sufficient to allow DOS wget to function successfully using
the 3Com UNDI/NDIS, Intel UNDI/NDIS, and UNDIPD.COM UNDI/PD stacks.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
This commit adds an igb (Intel GigaBit) driver based on Intel source
code available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support some PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit adds an e1000e driver based on Intel source code
available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support many PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit replaces the current gPXE e1000 driver with one ported
from Intel source code available at
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support most if not all PCI e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
The vxge driver code is split over several files, including vxge_main.c.
This causes the build system and ROM-o-matic to see the driver as
"vxge_main".
This patch adds a stub vxge.c which takes up no space but gives the
driver its proper name, "vxge".
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Align each ICM member alloc to the member size instead of page size.
Increase multicast table size to 128.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The rtl818x driver uses programmed I/O but has a fallback to
memory-mapped I/O registers. The fallback currently will not work since
the registers are accessed using inl()/outl() programmed I/O functions
in the driver. This patch removes the fallback to we fail cleanly when
programmed I/O is not possible.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This driver uses programmed I/O to access hardware registers. There is
a stray memory-mapped I/O read on a programmed I/O address. Perhaps
this is an artifact of porting the driver. Fix this by converting it to
programmed I/O.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This seems to be necessary for some types of PCI devices. We had
problems when using gPXE in KVM virtual machines with direct
PCI device access.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The previous [skge] commit should have been recorded as authored by
Thomas Miletich <thomas.miletich@gmail.com>
I mistakenly committed it improperly after fixing a merge issue.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This code is based on the linux skge driver. It supports Marvell Yukon
and SysKonnect Gigabit chipsets.
The code is based on code Michael Decker <mrd999@gmail.com> wrote for
Google Summer of Code 2008.
Support for dual-port cards is untested. The code, however, was left
in. In my opinion it's easier to fix the code if we need to, instead
of having to add support for it from scratch.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This driver supports all current Myricom 10 gigabit Ethernet NICs.
It was written from scratch for gPXE by Glenn Brown <glenn@myri.com>,
referenencing Myricom's Linux and EFI drivers, with permission.
Signed-off-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This version is Based on Michael Decker's GSoC 2008 code.
A number cleanups and fixes were applied.
Earlier-version-reviewed-by: Marty Connor <mdc@etherboot.org>
Earlier-version-tested-by: Marty Connor <mdc@etherboot.org>
Earlier-version-tested-by: Shao Miller <Shao.Miller@yrdsb.edu.on.ca>
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Reviewed-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The 82571 supports an alternate MAC address location in NVRAM.
When this is set, use this for the MAC rather than the default
physical MAC address.
Ported from linux-2.6.git 93ca161027eb6a1761fb674ad7b995aedccf5f6e
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The latest RTL-generated register lists include (mostly redundant)
xxx_MSB values alongside xxx_LSB and xxx_RMASK, and also include
default register values.
Some subnet managers expect the GetResponse from a SetPortInfo MAD to
contain the new link state. The transition is not immediate, so we
often end up returning the previous link state. This can cause the SM
to fail to activate the port.
Fix by waiting for up to 20us for the link state transition to take
effect.
The first byte of the IPoIB MAC address is used for flags indicating
support for "connected mode". Strip out the non-QPN bits of the first
dword when constructing the address vector for transmitted IPoIB
packets, so as not to end up passing an invalid QPN in the BTH.
Error message was:
[BUILD] bin/atl1e.oncc1: warnings being treated as errors
drivers/net/atl1e.c: In function 'atl1e_get_permanent_address':
drivers/net/atl1e.c:1326: error: dereferencing type-punned pointer will break strict-aliasing rules
make: *** [bin/atl1e.o] Error 1
Reported-by: Giandomenico De Tullio <ghisha@email.it>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Modified-by: Michael Brown <mcb30@etherboot.org>
Remove spaces in 3rd PCI_ROM field.
Debugged-by: Marty Connor <mdc@etherboot.org>
Reported-by: Giandomenico De Tullio <ghisha@email.it>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The iBFT is Ethernet-centric in providing only six bytes for a MAC
address. This is most probably an indirect consequence of a similar
design flaw in the Windows NDIS stack. (The WinOF IPoIB stack
performs all sorts of contortions in order to pretend to the NDIS
layer that it is dealing with six-byte MAC addresses.)
There is no sensible way in which to extend the iBFT without breaking
compatibility with programs that expect to parse it. Add the notion
of an "Ethernet-compatible" MAC address to our link layer abstraction,
so that link layers can provide their own workarounds for this
limitation.
gcc 3.3.3 gave the following error when compiling sis190.c
drivers/net/sis190.c: In function 'sis190_get_mac_addr_from_apc':
drivers/net/sis190.c:966: warning: 'isa_bridge' might be used
uninitialized in this function
make: *** [bin/sis190.o] Error 1
This patch allows error-free compilation.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Some BIOSes set the PCI cacheline size to zero for the card; the ath5k
driver fixes it to a reasonable in PCI config space, but failed to
correct the internal value it had already read. This resulted in
divide-by-zero errors when cacheline-aligning various data structures.
Fix by setting the internal cachelsz to a sane value at the same time
as we write that value to PCI config space.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This adds basic rfkill support for enabling the wireless card on certain
laptops, and changes miscellaneous other details that may help in obscure
cases.
Also change the error handling to not report CRC errors, which due to the
basic facts of wireless may happen even more frequently than valid packets.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Add the 82576 to the e1000 driver.
- Examining the Linux 2.6.30-rc4 igb driver, which supports this card and;
- Information available in the Intel® 82576 Gigabit Ethernet
Controller Datasheet v2.1, which is available from Intel's web site.
I only have a dual-ported card with Copper PHY, so any code paths relating
to Fibre haven't been tested. Also, I have only tested using auto-negotiation
of speed and duplex, and no flow control. Other code paths relating to
those settings also have not been exercised.
Signed-off-by: Simon Horman <horms@verge.net.au>
Sponsored-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Enable interrupts in sis900_irq(). Doing so allows some programs using
gPXE's UNDI interface to work properly, including Symantec Ghost.
Tested-by: Hubert Mercier <hubert.mercier@unilim.fr>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Both methods disabled packet tx and rx just to have it enabled again
by calling a3c90x_reset().
Fixed by disabling tx and rx after the call to a3c90x_reset().
Tested by booting Ubuntu intrepid(8.10) directly from gPXE and pxelinux.
Tested on 3c905, 3c905B, 3c905C.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Some systems will retry their boot sequence in the event of a boot
failure. On these systems, the second and subsequent boot attempts
will fail to initialise the Hermon HCA.
Fix by resetting the HCA during probe(). This incurs a one-second
cost, but there seems to be no viable alternative.
Originally-fixed-by: Itay Gazit <itaygazit@gmail.com>
Some devices can only be reset via a mechanism that also resets the
card's PCI core, thus necessitating a backup and restore of all or
part of the PCI configuration space across a reset.
IPoIB has a 20-byte link-layer address, of which only eight bytes
represent anything relating to a "hardware address".
The PXE and EFI SNP APIs expect the permanent address to be the same
size as the link-layer address, so fill in the "permanent address"
field with the initial link layer address (as generated by
register_netdev() based upon the real hardware address).
The hardware address is an intrinsic property of the hardware, while
the link-layer address can be changed at runtime. This separation is
exposed via APIs such as PXE and EFI, but is currently elided by gPXE.
Expose the hardware and link-layer addresses as separate properties
within a net device. Drivers should now fill in hw_addr, which will
be used to initialise ll_addr at the time of calling
register_netdev().
With iSCSI, connection attempts are expensive; it may take many
seconds to determine that a connection will fail. SRP connection
attempts are much less expensive, so we may as well avoid the
"optimisation" of declaring a state of permanent failure after a
certain number of attempts. This allows a gPXE SRP initiator to
resume operations after an arbitrary amount of SRP target downtime.
SRP is the SCSI RDMA Protocol. It allows for a method of SAN booting
whereby the target is responsible for reading and writing data using
Remote DMA directly to the initiator's memory. The software initiator
merely sends and receives SCSI commands; it never has to touch the
actual data.
The ACK timeout determines how long we take to notice a failed
Reliable Connection. Reducing it from the arbitrary value of 19 down
to 14 reduces the individual ACK timeout from around 2.1s to 67ms;
this in turn reduces the time to tear down and re-establish a broken
SRP session from around 30s to around 1s.
The Infiniband Communication Manager will refuse to establish a
connection if it believes the connection is already established.
There is no immediately obvious way to ask it to tear down the
existing connection and replace it; to issue a DREP we would need to
know the local and remote communication IDs used for the previous
connection setup.
We can work around this by randomising the high-order bits of the
queue pair number; these have no significance to the hardware, but are
sufficient to convince the IB CM that this is a different connection.
The prior net80211 model of physical-layer behavior for drivers was
overly simplistic and limited the drivers that could be written. To
be more flexible, split the driver-provided list of supported rates by
band, and add a means for specifying a list of supported channels.
Allow drivers to specify a hardware channel value that will be tied to
uses of the channel.
Expose net80211_duration() to drivers, and make the rate it uses in
its computations configurable, so that it can be used in calculating
durations that must be set in hardware for ACK and CTS packets. Add
net80211_cts_duration() for the common case of calculating the
duration for a CTS packet.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The IBA specification refers to management "interfaces" and "agents".
The interface is the component that connects to the queue pair and
sends and receives MADs; the agent is the component that constructs
the reply to the MAD.
Rename the IB_{QPN,QKEY,QPT} constants as a first step towards making
this separation in gPXE.
The Linux IB Communication Manager will always send MADs to QP1,
rather than back to the originating QP. On Hermon, QP1 is by default
handled by the embedded firmware. We can change this, but the cost is
that we have to handle both QP0 and QP1 (i.e. we have to provide SMA
as well as GMA service in software), and we have to use MLX queues
rather than standard UD queues (i.e. we have to construct the UD
datagrams by hand).
There doesn't seem to be any viable way around this situation, ugly
though it is.
Queue pairs are now assumed to be created in the INIT state, with a
call to ib_modify_qp() required to bring the queue pair to the RTS
state.
ib_modify_qp() no longer takes a modification list; callers should
modify the relevant queue pair parameters (e.g. qkey) directly and
then call ib_modify_qp() to synchronise the changes to the hardware.
The packet sequence number is now a property of the queue pair, rather
than of the device.
Each queue pair may have an associated address vector. For RC queue
pairs, this is the address vector that will be programmed in to the
hardware as the remote address. For UD queue pairs, it will be used
as the default address vector if none is supplied to ib_post_send().
The queue key is stored as a property of the queue pair, and so can
optionally be added by the Infiniband core at the time of calling
ib_post_send(), rather than always having to be specified by the
caller.
This allows IPoIB to avoid explicitly keeping track of the data queue
key.
Now that path record lookups are handled entirely via
ib_resolve_path(), the only role of the IPoIB peer cache is as a
lookup table for MAC addresses. Update the code structure and
comments to reflect this.
The IPoIB broadcast MAC address varies according to the partition key.
Now that the broadcast MAC address is a property of the network device
rather than of the link layer, we can expose this real MAC address
directly.
The broadcast LID is now identified via a path record lookup; this is
marginally inefficient (since it was present in the MCMemberRecord
GetResponse), but avoids the need to special-case broadcasts when
constructing the address vector in ipoib_transmit().
Currently, all Infiniband users must create a process for polling
their completion queues (or rely on a regular hook such as
netdev_poll() in ipoib.c).
Move instead to a model whereby the Infiniband core maintains a single
process calling ib_poll_eq(), and polling the event queue triggers
polls of the applicable completion queues. (At present, the
Infiniband core simply polls all of the device's completion queues.)
Polling a completion queue will now implicitly refill all attached
receive work queues; this is analogous to the way that netdev_poll()
implicitly refills the RX ring.
Infiniband users no longer need to create a process just to poll their
completion queues and refill their receive rings.
IPoIB and the SMA have separate constants for the packet size to be
used to I/O buffer allocations. Merge these into the single
IB_MAX_PAYLOAD_SIZE constant.
(Various other points in the Infiniband stack have hard-coded
assumptions of a 2048-byte payload; we don't currently support
variable MTUs.)
IPoIB has a link-layer broadcast address that varies according to the
partition key. We currently go through several contortions to pretend
that the link-layer address is a fixed constant; by making the
broadcast address a property of the network device rather than the
link-layer protocol it will be possible to simplify IPoIB's broadcast
handling.
Move the icky call to step() from aoe.c to ata.c; this takes it at
least one step further away from where it really doesn't belong.
Unfortunately, AoE has the ugly aoe_discover() mechanism which means
that we still have a step() loop in aoe.c for now; this needs to be
replaced at some future point.
Jarrod Johnson
Thomas Miletich
Christian Hesse
Michael Brown
Julian Pidancet
Scott K Logan
Yann Cézard
Itay Gazit
Masroor Vettuparambil
Alex Williamson
Shao Miller
Marty Connor
Piotr Jaroszyński
Andrei Faur
Stefan Hajnoczi
Glenn Brown
Geoff Lywood
Guo-Fu Tseng
Erwan Velu
Bruce Rogers
Michael Brown
Masroor Vettuparambil
Bernhard Kohl
Thomas Horsten
Alex Williamson
Joshua Oreman
Simon Horman
Joshua Oreman