Commit 947976d ("[netdevice] Do not force a poll on net_tx()")
requires network devices to have TX rings that are sufficiently large
to allow a transmitted response to all packets received during a
single poll.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel NIC emulation in some versions of VMware seems to suffer
from a flaw whereby the Interrupt Cause Register (ICR) fails to assert
the usual "packet received" bit (ICR.RXT0) if a receive overflow
(ICR.RXO) has also occurred.
Work around this flaw by polling for completed descriptors whenever
either ICR.RXT0 or ICR.RXO is asserted.
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Debugged-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Tested-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Almost all clients of the raw-packet interfaces (UNDI and SNP) can
handle only Ethernet link layers. Expose an Ethernet-compatible link
layer to local clients, while remaining compatible with IPoIB on the
wire. This requires manipulation of ARP (but not DHCP) packets within
the IPoIB driver.
This is ugly, but it's the only viable way to allow IPoIB devices to
be driven via the raw-packet interfaces.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards seem to drive the EEPROM CS line high (i.e. active)
when 9346CR.EEM is set to "normal operating mode", with the result
that the CS line is never deasserted. The symptom of this is that the
first read from the EEPROM will work, while all subsequent reads will
return garbage data.
Reported-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up advertising
only 100Mbps, despite being capable of 1000Mbps. Forcibly enable
advertisement of 1000Mbps on any RTL8169-like card.
This change relies on the assumption that the CTRL1000 register will
not exist on 100Mbps-only RTL8169 cards such as the RTL8101.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) crash and burn if DAC
is enabled, even if only 32-bit addresses are used. Observed
behaviour includes system lockups and repeated transmission of garbage
data onto the wire.
This seems to be a known problem. The Linux r8169 driver disables DAC
by default and provides a "use_dac" module parameter.
There appears to be no known test for determining whether or not DAC
will work. As a workaround, enable DAC only if we are built as as
64-bit binary. This at least eliminates the problem in the common
case of a 32-bit build, which will never use 64-bit addresses anyway.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some bits in the C+ Command register are always one. Testing for the
presence of the register must allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with
TCR.MXDMA set to 16 bytes. While this does not prevent proper
operation, it almost certainly degrades performance.
Fix by explicitly setting TCR.MXDMA to "unlimited".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with invalid
values in RCR.RXFTH and RCR.MXDMA, causing receive DMA to fail. Fix
by setting explicit values for both fields.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with garbage
values in the ring address registers, and do not clear the registers
on reset.
Fix by always setting the high dword of the ring address registers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Change the DMA alignment from 4096 bytes to 16 bytes, to conserve
available DMA memory. The hardware doesn't have any specific
alignment requirements.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Datasheet pp. 41-42 defines 'rx packet length' as upper word of
'status' dword field of the receive descriptor table.
http://www.smsc.com/media/Downloads_Archive/discontinued/83c171.pdf
Tested on SMC EtherPower II.
Signed-off-by: Alexey Smazhenko <darkover@corbina.com.ua>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc 4.7 produces a spurious warning about an array subscript being out
of bounds. Use a pointer dereference instead of an array lookup to
inhibit this spurious warning.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On i350 the datasheet contradicts itself in stating that the default
value of RXDCTL.ENABLE for queue zero is both set (according to the
"Receive Initialization" section) and unset (according to the "Receive
Descriptor Control - RXDCTL" section). Empirical evidence suggests
that the default value is unset.
Explicitly enable both transmit and receive queues to avoid any
ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 82576 (and probably others), the datasheet states that "the tail
register of the queue (RDT[n]) should not be bumped until the queue is
enabled". There is some confusion over exactly what constitutes
"enabled": the initialisation blurb says that we should "poll the
RXDCTL register until the ENABLE bit is set", while the description
for the RXDCTL register says that the ENABLE bit is set by default
(for queue zero). Empirical evidence suggests that the ENABLE bit
reads as set immediately after writing to RCTL.EN, and so polling is
not necessary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hw pointer in PCI driver data as expected by sky2_remove().
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RTL8139C+ cards use essentially the same datapath as RTL8169, which is
zerocopy and 64-bit capable. Older RTL8139 cards use a single receive
ring buffer rather than a descriptor ring, but still share substantial
amounts of functionality with RTL8169.
Include support for RTL8139 cards within the generic Realtek driver,
since there is no way to differentiate between RTL8139 and RTL8139C+
cards based on the PCI IDs alone.
Many thanks to all the people who worked on the rtl8139 driver over
the years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The link state is currently set at probe time, and updated only when
the device is polled. This results in the user seeing a misleading
stale "Link: down" message, if autonegotiation did not complete within
the short timespan of the probe routine.
Fix by updating the link state when the device is opened, so that the
message that ends up being displayed to the user reflects the real
link state at device open time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE provides no support for manually configuring the link speed.
Provide a generic routine which should be able to reset any MII/GMII
PHY and enable autonegotiation.
Prototyped-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for 82579-based chips such as those found on Sandy Bridge
motherboards. Based on d3738bb8203acf8552c3ec8b3447133fc0938ddd in
Linux.
Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Practically speaking, it seems the convention is to only have one
packet pending and not rely upon any mechanism to associate returned
txbuf with txqueue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This function never did much in this driver anyway, and after commit
b5ed30b2 ("[tg3] Fix compilation on newer gcc versions") it became
apparent that its remaining functionality could be easily moved to
tg3_test_dma().
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old Etherboot tg3 driver with a more up-to-date driver
using the iPXE API.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RS bit is used to instruct the NIC to update the TX descriptor
status byte. The RPS bit is used to instruct the NIC to defer this
update until after the packet has been transmitted on the wire (rather
than merely read into the transmit FIFO).
The driver currently sets RPS but not RS. Some e1000 models seem to
interpret this as implying that the status byte should be updated;
some don't. On the ones that don't, we never see any TX completions
and so rapidly run out of TX buffers.
Fix by setting the RS bit in the TX descriptor. (We don't care about
when the packet reaches the wire, so don't bother setting the RPS
bit.)
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
WinPE has been observed to call PXENV_UNDI_SHUTDOWN but not
PXENV_STOP_UNDI. This means that Hermon hardware is left partially
active (firmware running and one event queue mapped) when WinPE starts
up, which can cause a Blue Screen of Death.
Fix by ensuring that the hardware is left quiescent (with the firmware
stopped) when no interfaces are open.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid spurious matches for peer key 0 against empty peer cache
entries, and set the LL_MULTICAST flag in addition to LL_BROADCAST.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ChipCmd register is only an 8-bit register. The 16-bit access
used by iPXE was causing an issue when used with qemu emulated rtl8139
device which was improperly aligning IOs.
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Arbel seems to crash the system as soon as the first send WQE
completes on an RC queue pair. (NOPs complete successfully, so this
is a problem specific to the work queue rather than the completion
queue.) The cause of this problem has remained unknown for over a
year.
Check in the non-functioning code to avoid bit-rot, and in the hope
that someone will find the fix.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reported-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This reverts commit 15c1200 ("[hermon] Work around missing mport
support in current BOFM implementations").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Current BOFM versions are unable to create entries with mport>1, which
means that only the port 1 MAC address can be explicitly specified.
Work around this by using the provided MAC address as a base address
for all subsequent ports. For example, if BOFM assigns the address
00:1A:64:76:00:09 for port 1
then we will assign the addresses
00:1A:64:76:00:09 for port 1
00:1A:64:76:00:0a for port 2
Future BOFM versions that may correctly support mport will work with
this scheme without modification provided that the BOFM entries are
created in increasing order of mport. Since BOFM tools tend to
generate entries in increasing order (of slot, port, etc), this is not
an unreasonable compromise.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE operates the forcedeth NIC in promiscuous mode, and never changes
the unicast MAC address filter registers. We should not therefore set
the flag indicating (to other drivers loaded later) that the MAC
address order has already been corrected.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The forcedeth driver currently implements unicast MAC address
filtering in software. This is almost invariably the wrong thing to
do (since the network stack must already be able to cope with unwanted
packets) and it breaks FCoE (which requires the card to operate in
promiscuous mode).
Also, the implementation is buggy: is_local_ether_addr() is used to
check for a locally-assigned Ethernet address (not to check for a
unicast address), and the current link-layer address is in
netdev->ll_addr, not netdev->hw_addr.
Fix by removing this code.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid unused-but-set variable warning in gcc 4.6 which was introduced
by commit 9215b7f ("[forcedeth] Clear the MII link status register on
link status changes").
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose a function setting_applies() to allow a caller to determine
whether or not a particular setting is applicable to a particular
settings block.
Restrict DHCP-backed settings blocks to accepting only DHCP-based
settings.
Restrict network device settings blocks to accepting only DHCP-based
settings and network device-specific settings such as "mac".
Inspired-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
From a cursory examination, it appears as though the calculation of
tx_available is redundant, since eepro_transmit() waits for transmit
completion before returning anyway.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On reset and close, the ICR register is read to clear any pending
interrupts, but the value is simply ignored. Avoid assigning the
value to a variable, to inhibit a warning from gcc 4.6.
Also fix a potential race condition in reset routines which clear
interrupts before disabling them.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
These unused portions trigger a compiler warning under gcc 4.6, due to
the ambiguity over the "page" field in struct igbvf_buffer.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a virtual environment such as qemu, we can legitimately receive
packets less than 64 bytes in length, such as ARP replies. These are
currently discarded, causing most IPv4 communication to fail.
Fix by ignoring the RFDShort bit when receiving packets.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading rtl8139.pxe from an old Etherboot rtl8139.zrom, iPXE
can end up misreading the first word of the MAC address from the
EEPROM as being all zeroes. This is presumably because Etherboot has
left the serial EEPROM in an unexpected state.
Fix by using the chip select line to reset the SPI device before we
start accessing it.
Reported-by: Mandar U Jog <mandarjog@gmail.com>
Tested-by: Mandar U Jog <mandarjog@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default initiator IQN is "iqn.2000-09.org.etherboot:UNKNOWN".
This is problematic for two reasons:
a) the etherboot.org domain (and hence the associated IQN namespace)
is not under the control of the iPXE project, and
b) some targets (correctly) refuse to allow concurrent connections
from different initiators using the same initiator IQN.
Solve both problems by changing the default initiator IQN to be
iqn.2010-04.org.ipxe:<hostname> if a hostname is set, or
iqn.2010-04.org.ipxe:<uuid> if no hostname is set.
Explicit initiator IQNs set via DHCP option 203 are not affected by
this change.
Unfortunately, this change is likely to break some existing
configurations, where ACL rules have been put in place referring to
the old default initiator IQN. Users may need to update ACLs, or
force the use of the old IQN using an iPXE script line such as
set initiator-iqn iqn.2000-09.org.etherboot:UNKNOWN
or a dhcpd.conf option such as
option iscsi-initiator-iqn "iqn.2000-09.org.etherboot:UNKNOWN"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some operating environments require (or at least prefer) that we do
not perform our own PCI bus scan, but deal only with specified
devices. Modularise the PCI core to allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge the "bus" and "devfn" fields into a single "busdevfn" field, to
match the format used by the majority of external code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 64-bit builds, MLX_DECLARE_STRUCT() produces a structure that is
always a multiple of 64 bits long, causing the HCR structure to be
over-length by one dword. This in turn causes hermon_cmd() to write
beyond the end of the HCR, which causes commands to fail.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leak of untreated events by having circular event queue
operation.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove duplicate hardware resets, remove network interface logic
reset.
This also fixes a bug where some 3c905C variants would return bogus
EEPROM values because of a too short delay after the network reset.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DBG is reserved for errors and important warnings only.
DBG2 for additional information, e.g. "received packet".
DBGP is used to print the name of every function as it is called.
Signed-off-by: Thomas Miletich<thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the concept of shutdown exit flags, and replace it with a
counter used to keep track of exposed interfaces that require devices
to remain active.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support a new function mode "multi-function 8 Direct IO" which is used
in ESX Direct I/O configuration.
Update driver version to 3.5.0.1
Signed-off-by: Masroor Vettuparambil <masroor.vettuparambil@exar.com>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@exar.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most xxx_init() functions are void functions with no failure cases.
Allow pci_vpd_init() to be used in the same way. (Subsequent calls to
pci_vpd_read() etc. will fail if pci_vpd_init() fails.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since its implementation several years ago, no driver has used a
fragment list containing more than a single fragment. Simplify the
NVO core and the drivers that use it by removing the whole concept of
the fragment list, and using a simple (address,length) pair instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Driver for Intel 82576 based virtual functions, based on Intel source
code available at:
http://sourceforge.net/projects/e1000 (igbvf-1.0.7)
Based on initial port from Eric Keller <ekeller@princeton.edu>.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Changes were made to files where the licence text within the files
themselves confirms that the files are GPL version 2 or later.
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Pass the settings block name as a parameter to register_settings(),
rather than defining it with settings_init() (and then possibly
changing it by directly manipulating settings->name).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some SCSI targets (observed with an EMC CLARiiON Fibre Channel target)
will not respond to commands correctly until a TEST UNIT READY has
been issued. In particular, a READ CAPACITY (10) command will return
with a success status, but no capacity data.
Fix by issuing a TEST UNIT READY command automatically, and delaying
further SCSI commands until the TEST UNIT READY has succeeded.
Reported-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires us to be able to receive unicast packets for multiple
addresses. Support this by operating in promiscuous mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PRM structures to support Hermon Ethernet devices.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Unlike Arbel, port parameters must be applied via a separate call to
SET_PORT, rather than as parameters to INIT_PORT.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Mapping a single page at a time causes a several-second delay at
device initialisation time. Reduce this by mapping multiple pages at
a time, using the largest block sizes possible given the alignment
constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Mapping a single page at a time causes a several-second delay at
device initialisation time. Reduce this by mapping multiple pages at
a time, using the largest block sizes possible given the alignment
constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use individual page mappings rather than a single whole-region
mapping, to avoid the waste of memory that occurs due to the
constraint that each mapped block must be aligned on its own size.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Backport some changes from the Hermon driver to the Arbel driver.
Specifically:
o Rename reserved_lkey to lkey
o Add arbel_rate() to calculate transmission rates
o Structure code to allow for addition of RC queue pairs
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the amount of ICM space required by choosing to order the
various allocations in approximately descending order of alignment
requirements.
This saves approximately 512kB of host memory.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current method for ICM allocation exactly matches the addresses
chosen by the old Etherboot driver, but does not match the
specification. Some ICM tables (notably the queue pair context table)
therefore end up incorrectly aligned.
Fix by performing allocations as per the specification.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the utility of debugging messages by including the relevant
port number, queue number (QPN, CQN, EQN), work queue entry (WQE)
number, and physical addresses wherever applicable.
Add arbel_dump_cqctx() for dumping a completion queue context and
arbel_dump_qpctx() for dumping a queue pair context.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This is a backport of commit 0b1222f ("[hermon] Randomise the
high-order bits of queue pair numbers") to the Arbel driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This is a backport of commit cd5a213 ("[hermon] Allow software GMA to
receive packets destined for QP1") to the Arbel driver.
This patch includes a correction to a bug in the autogenerated
hardware description header file.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Only port state change events are currently mapped to our event queue,
since those are the only events we are prepared to handle. This
ignores a potentially useful source of diagnostic information in the
case of unexpected failures.
Fix by mapping all events to the event queue; a build with debugging
enabled will therefore at least dump the raw content of the unexpected
events.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Only port state change events are currently mapped to our event queue,
since those are the only events we are prepared to handle. This
ignores a potentially useful source of diagnostic information in the
case of unexpected failures.
Fix by mapping all events to the event queue; a build with debugging
enabled will therefore at least dump the raw content of the unexpected
events.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently uses the first port's port GUID as the node GUID,
rather than using the (possibly distinct) real node GUID. This can
confuse opensm during the handover to a loaded OS: it thinks the port
already belongs to a different node and so discards our port
information with a warning message about duplicate ports. Everything
is picked up correctly on the second subnet sweep, after opensm has
established that the "old" node no longer exists, but this can delay
link-up unnecessarily by several seconds.
Fix by using the real node GUID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No event is generated upon reaching INIT, so we must poll separately
for link state changes while we remain DOWN.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No event is generated upon reaching INIT, so we must poll separately
for link state changes while we remain DOWN.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ib_smc_update() potentially updates the Infiniband port state, and so
should almost always be followed by a call to ib_link_state_changed().
The one exception is the call made to ib_smc_update() before the
device is registered.
Fix by removing explicit calls to ib_link_state_changed() from drivers
using ib_smc_update(), including a call to ib_link_state_changed()
within ib_smc_update(), and creating a separate ib_smc_init() for use
prior to device registration.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The sense key gives a first idea of what the problem might be, and so
is potentially useful in diagnosing problems in a non-debug build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The block device interface used in gPXE predates the invention of even
the old gPXE data-transfer interface, let alone the current iPXE
generic asynchronous interface mechanism. Bring this old code up to
date, with the following benefits:
o Block device commands can be cancelled by the requestor. The INT 13
layer uses this to provide a global timeout on all INT 13 calls,
with the result that an unexpected passive failure mode (such as
an iSCSI target ACKing the request but never sending a response)
will lead to a timeout that gets reported back to the INT 13 user,
rather than simply freezing the system.
o INT 13,00 (reset drive) is now able to reset the underlying block
device. INT 13 users, such as DOS, that use INT 13,00 as a method
for error recovery now have a chance of recovering.
o All block device commands are tagged, with a numerical tag that
will show up in debugging output and in packet captures; this will
allow easier interpretation of bug reports that include both
sources of information.
o The extremely ugly hacks used to generate the boot firmware tables
have been eradicated and replaced with a generic acpi_describe()
method (exploiting the ability of iPXE interfaces to pass through
methods to an underlying interface). The ACPI tables are now
built in a shared data block within .bss16, rather than each
requiring dedicated space in .data16.
o The architecture-independent concept of a SAN device has been
exposed to the iPXE core through the sanboot API, which provides
calls to hook, unhook, boot, and describe SAN devices. This
allows for much more flexible usage patterns (such as hooking an
empty SAN device and then running an OS installer via TFTP).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Doorbell records are currently embedded within the completion queue
and receive work queue strucures, which are allocated using zalloc()
and so have an alignment guarantee of only sizeof(void*), i.e. four
bytes. This is sufficient for the receive work queue, but not for the
completion queue, which requires an alignment guarantee of eight
bytes.
Though not guaranteed, it so happens that zalloc() will always return
a pointer that is exactly four bytes above a sixteen-byte boundary.
The completion queue doorbell record is therefore always misaligned,
and the value passed to the hardware via SW2HW_CQ is actually always
pointing to the page_offset value within the MTT descriptor (which
directly precedes the inline doorbell record). Provided that the page
offset is greater than 0x100, this looks to the hardware like an
update_ci value of greater than 0x010000 (taking into account
endianness differences), and so the hardware will happily deliver more
than 0x010000 completions before stopping. Hence this problem is
rarely observable.
Fix by allocating the doorbell records separately and using the
correct alignment constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give completion queues a chance to deliver exception events by
programming in the number of our event queue (currently used only for
port state changes).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the utility of debugging messages by including the relevant
port number, queue number (QPN, CQN, EQN), work queue entry (WQE)
number, and physical addresses wherever applicable.
Add hermon_dump_cqctx() for dumping a completion queue context, and
hermon_fill_nop_send_wqe() for inserting NOPs into send work queues.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An attempt to transmit a packet of 8192 bytes or larger will collide
with the status bits in the TX descriptor. This gives the appearance
of the network card's transmit data path having just suddenly stopped
responding; iPXE is waiting for the card to report a TX completion
but, because of the status bit collision, the card thinks that the
descriptor has not yet been written.
Fix by explicitly checking for oversized packets in rtl_transmit().
Discovered during Fibre Channel over Ethernet testing, and debugged by
using gdb to examine the state of the emulated rtl8139 card in qemu.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the explicit calls from the Infiniband core to the IPoIB layer
with the general concept of an Infiniband upper-layer driver
(analogous to a PCI driver) which can create arbitrary devices on top
of Infiniband devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The rtl8139 driver includes the Ethernet CRC within the received
packet. All current protocols ignore trailing garbage, but FCoE
requires the frame length to be correct (since the FCoE footer
position is calculated from the end of the packet), so fix the driver
to strip out the CRC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PCI ID 8086:27dc to the eepro100 driver.
Reported-by: Cédric Delmas <c.delmas@akka.eu>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the tap driver that can be used like:
$ ./ipxe.linux --net tap,if=tap0,mac=00:0c:29:c5:39:a1
The if setting is mandatory.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the base to build linux drivers and the linux UI code on. UI
fills device requests, which are later walked over by the linux
root_driver and delegated to specific linux drivers.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
alloc_memblock() and free_memblock() are internal.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
pcbios specific get_memmap() is used by the b44 driver making
all-drivers builds fail on other platforms. Move it to the I/O API
group and provide a dummy implementation on EFI.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE forcedeth driver and removes the legacy
Etherboot forcedeth driver. It supports 40 different chips, compared
to the original 14.
It has been tested on a NIC with an CK804 Ethernet Controller, and the
results of downloading 5 100mb images in a row have been:
12/11/11/11/11 seconds; booting DSL using pxelinux also succeeded. The
driver has also been tested by chaining undionly.kpxe and it worked.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Tested-by: Andrei Faur <da3drus@gmail.com>
Tested-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE virtio-net driver and removes the legacy
Etherboot virtio-net driver. The main reasons for doing this are:
1. Multiple virtio-net NICs are now supported by iPXE. The legacy
driver kept global state and caused issues in virtual machines with
more than one virtio-net device.
2. Faster downloads. The native iPXE driver downloads 100 MB over
HTTP in 12s, the legacy Etherboot driver in 37s. This simple
benchmark uses KVM with tap networking and the Python
SimpleHTTPServer both running on the same host.
Changes to core virtio code reduce vring descriptors to 256 (QEMU uses
128 for virtio-blk and 256 for virtio-net) and change the opaque token
from u16 to void*. Lowering the descriptor count reduces memory
consumption. The void* opaque token change makes driver code simpler.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This bug caused .probe to fail because the NIC did not reset properly.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add NonVolatile Option (nvo) and NonVolatile Storage (nvs) support to
the myri10ge driver using the EEPROM read/write mechanism provided by
the NIC's Vendor Specific PCI capability.
The myri10ge NIC is capabile of storing 64KB or more of nonvolatile
options, but this patch advertises only 512 bytes of nvo storage
because iPXE malloc's a buffer matching the total size we advertise.
512 is plenty without wasting malloc'd memory. (The 2 other drivers
currently supporting nvo advertise 256 bytes or less.)
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch removes the cfg lookup made in the r8169 driver and
replaces it with equivalent information found in the driver_data field
of the pci_device_id structure.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove data-xfer as an interface type, and replace data-xfer
interfaces with generic interfaces supporting the data-xfer methods.
Filter interfaces (as used by the TLS layer) are handled using the
generic pass-through interface capability. A side-effect of this is
that deliver_raw() no longer exists as a data-xfer method. (In
practice this doesn't lose any efficiency, since there are no
instances within the current codebase where xfer_deliver_raw() is used
to pass data to an interface supporting the deliver_raw() method.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using ref_init() to initialise an embedded reference
count, to match the coding style used by other embedded objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch replaces the old pcnet32 driver with a new one that
uses iPXE's API.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
After changing the driver to refill after feed, if any error occurs a
non-contiguous empty buffer will be introduced in the ring due to my
reuse-buffer-when-error implementation.
Reported-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Kevin Tran
Thomas Miletich
Alexey
Valentine Barshak
Erik Jacobson
Daniel Hokka Zakrisson
Olaf Hering
1d 2k
Jarrod Johnson
Christian Hesse
Julian Pidancet
Scott K Logan
Yann Cézard
Itay Gazit
Masroor Vettuparambil
Alex Williamson
Shao Miller
Marty Connor
Piotr Jaroszyński
Andrei Faur
Stefan Hajnoczi
Glenn Brown
Geoff Lywood
Guo-Fu Tseng