When connected to a USB3 port, the AX88179 seems to have an
approximately 50% chance of producing a USB transaction error on each
of its three endpoints after being closed and reopened. The root
cause is unclear, but rewriting the USB device configuration value
seems to clear whatever internal error state has accumulated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Experimentation shows that the existing 20ms delay is insufficient,
and often results in device detection being deferred until after iPXE
has completed startup.
Fix by increasing the delay to 100ms.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The driver-private data for root hubs is already set immediately after
allocating the USB bus. There seems to be no reason to set it again
when opening the root hub.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "disabled" port states for USB2 and USB3 are not directly
equivalent. In particular, a disabled USB3 port will not detect new
device connections. The result is that a USB3 device disconnected
from and reconnected to an xHCI root hub port will end up reconnecting
as a USB2 device.
Fix by setting the link state to RxDetect after disabling the port, as
is already done during initialisation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The USB3 specification removes PORT_ENABLE from the list of features
that may be cleared via a CLEAR_FEATURE request. Experimentation
shows that omitting the attempt to clear PORT_ENABLE seems to result
in the correct hotplug behaviour.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Resetting the host endpoint may immediately restart any pending
transfers for that endpoint. If the device endpoint halt has not yet
been cleared, then this will probably result in a second failed
transfer.
This second failure may be detected within usb_endpoint_reset() while
waiting for usb_clear_feature() to complete. The endpoint will
subsequently be removed from the list of halted endpoints, causing the
second failure to be effectively ignored and leaving the host endpoint
in a permanently halted state.
Fix by deferring the host endpoint reset until after the device
endpoint is ready to accept new transfers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ASIX USB NICs are capable of autodetecting the Ethernet link speed
and reporting it via PLSR but will not automatically update the
relevant GM and PS bits in MSR. The result is that a non-gigabit link
will fail to send or receive any packets.
The interrupt endpoint used to report link state includes the values
of the PHY BMSR and LPA registers. These are not sufficient to
differentiate between 100Mbps and 1000Mbps, since the LPA_NPAGE bit
does not necessarily indicate that the link partner is advertising
1000Mbps.
Extend axge_check_link() to write the MSR value based on the link
speed read from PLSR, and simplify the interrupt endpoint handler to
merely trigger a call to axge_check_link().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As per commit c89a446 ("[efi] Run at TPL_CALLBACK to protect against
UEFI timers") we expect to run at TPL_CALLBACK almost all of the time.
Various code paths rely on this assumption. Code paths that need to
temporarily lower the TPL (e.g. for entropy gathering) will restore it
to TPL_CALLBACK.
The entropy gathering code will be run during DRBG initialisation,
which happens during the call to startup(). In the case of iPXE
compiled as an EFI application this code will run within the scope of
efi_snp_claim() and so will execute at TPL_CALLBACK as expected.
In the case of iPXE compiled as an EFI driver the code will
incorrectly run at TPL_APPLICATION since there is nothing within the
EFI driver entry point that raises (and restores) the TPL. The net
effect is that a build that includes the entropy-gathering code
(e.g. a build with HTTPS enabled) will return from the driver entry
point at TPL_CALLBACK, which causes a system lockup.
Fix by raising and restoring the TPL within the EFI driver entry
point.
Debugged-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The EFI_RNG_PROTOCOL on the Microsoft Surface Go does not generate
random numbers. Successive calls to GetRNG() without any intervening
I/O operations (such as writing to the console) will produce identical
results. Successive reboots will produce identical results.
It is unclear what the Microsoft Surface Go is attempting to use as an
entropy source, but it is demonstrably producing zero bits of entropy.
The failure is already detected by the ANS-mandated Repetition Count
Test performed as part of our GetEntropy implementation. This
currently results in the entropy source being marked as broken, with
the result that iPXE refuses to perform any operations that require a
working entropy source.
We cannot use the existing EFI driver blacklisting mechanism to unload
the broken driver, since the RngDxe driver is integrated into the
DxeCore image.
Work around the broken driver by checking for consecutive identical
results returned by EFI_RNG_PROTOCOL and falling back to the original
timer-based entropy source.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of gcc (observed with the cross-compiling gcc 9.3.0 in
Ubuntu 20.04) default to enabling -fPIE. Experimentation shows that
this results in the emission of R_AARCH64_ADR_GOT_PAGE relocation
records for __stack_chk_guard. These relocation types are not
supported by elf2efi.c.
Fix by explicitly disabling position-independent code for ARM64 EFI
builds.
Debugged-by: Antony Messerli <antony@mes.ser.li>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
GCC 10 emits warnings for implicit conversions of enumerated types.
The flexboot_nodnic code defines nodnic_queue_pair_type with values
identical to those of ib_queue_pair_type, and implicitly casts between
them. Add an explicit cast to fix the warning.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
GCC 10 produces a spurious warning about an out-of-bounds array access
for the unsized raw dword array in union intelvf_msg.
Avoid the warning by embedding the zero-length array within a struct.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc10 switched default behavior from -fcommon to -fno-common. Since
"__shared" relies on the legacy behavior, explicitly specify it.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Various implementation quirks in OCSP servers make it impractical to
use anything other than SHA1 to construct the issuerNameHash and
issuerKeyHash identifiers in the request certID. For example: both
the OpenCA OCSP responder used by ipxe.org and the Boulder OCSP
responder used by LetsEncrypt will fail if SHA256 is used in the
request certID.
As of commit 6ffe28a ("[ocsp] Accept response certID with missing
hashAlgorithm parameters") we rely on asn1_digest_algorithm() to parse
the algorithm identifier in the response certID. This will fail if
SHA1 is disabled via config/crypto.h.
Fix by using a direct ASN.1 object comparison on the OID within the
algorithm identifier.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Enable -fstack-protector for EFI builds, where binary size is less
critical than for BIOS builds.
The stack cookie must be constructed immediately on entry, which
prohibits the use of any viable entropy source. Construct a cookie by
XORing together various mildly random quantities to produce a value
that will at least not be identical on each run.
On detecting a stack corruption, attempt to call Exit() with an
appropriate error. If that fails, then lock up the machine since
there is no other safe action that can be taken.
The old conditional check for support of -fno-stack-protector is
omitted since this flag dates back to GCC 4.1.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some devices (observed with a Getac RX10 tablet and docking station
containing an embedded AX88179 USB NIC) seem to be capable of
detecting link state only during the call to Initialize(), and will
occasionally erroneously report that the link is down for the first
few such calls.
Work around these devices by retrying the Initialize() call multiple
times, terminating early if a link is detected. The eventual absence
of a link is treated as a non-fatal error, since it is entirely
possible that the link really is down.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Disable the use of MD5 as an OID-identifiable algorithm. Note that
the MD5 algorithm implementation will still be present in the build,
since it is used implicitly by various cryptographic components such
as HTTP digest authentication; this commit removes it only from the
list of OID-identifiable algorithms.
It would be appropriate to similarly disable the use of SHA-1 by
default, but doing so would break the use of OCSP since several OCSP
responders (including the current version of openca-ocspd) are not
capable of interpreting the hashAlgorithm field and so will fail if
the client uses any algorithm other than the configured default.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There are many ways in which the object for a cryptographic algorithm
may be included, even if not explicitly enabled in config/crypto.h.
For example: the MD5 algorithm is required by TLSv1.1 or earlier, by
iSCSI CHAP authentication, by HTTP digest authentication, and by NTLM
authentication.
In the current implementation, inclusion of an algorithm for any
reason will result in the algorithm's ASN.1 object identifier being
included in the "asn1_algorithms" table, which consequently allows the
algorithm to be used for any ASN1-identified purpose. For example: if
the MD5 algorithm is included in order to support HTTP digest
authentication, then iPXE would accept a (validly signed) TLS
certificate using an MD5 digest.
Split the ASN.1 object identifiers into separate files that are
required only if explicitly enabled in config/crypto.h. This allows
an algorithm to be omitted from the "asn1_algorithms" table even if
the algorithm implementation is dragged in for some other purpose.
The end result is that only the algorithms that are explicitly enabled
in config/crypto.h can be used for ASN1-identified purposes such as
signature verification.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The supported ciphers and digest algorithms may already be specified
via config/crypto.h. Extend this to allow a minimum TLS protocol
version to be specified.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some platforms (observed with an AMI BIOS on an Apollo Lake system)
will spuriously fail the call to ConnectController() when the UEFI
network stack is disabled. This appears to be a BIOS bug that also
affects attempts to connect any non-iPXE driver to the NIC controller
handle via the UEFI shell "connect" utility.
Work around this BIOS bug by falling back to calling our
efi_driver_start() directly if the call to ConnectController() fails.
This bypasses any BIOS policy in terms of deciding which driver to
connect but still cooperates with the UEFI driver model in terms of
handle ownership, since the use of EFI_OPEN_PROTOCOL_BY_DRIVER ensures
that the BIOS is aware of our ownership claim.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The URI parsing code for "host[:port]" checks that the final character
is not ']' in order to allow for IPv6 literals. If the entire
"host[:port]" portion of the URL is an empty string, then this will
access the preceding character. This does not result in accessing
invalid memory (since the string is guaranteed by construction to
always have a preceding character) and does not result in incorrect
behaviour (since if the string is empty then strrchr() is guaranteed
to return NULL), but it does make the code confusing to read.
Fix by inverting the order of the two tests.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As described in the previous commit, work around a UEFI specification
bug that necessitates calling UnloadImage if the return value from
LoadImage is EFI_SECURITY_VIOLATION.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently assumes that any error returned from LoadImage()
indicates that the image was not loaded. This assumption was correct
at the time the code was written and remained correct for UEFI
specifications up to and including version 2.1.
In version 2.3, the UEFI specification broke API and ABI compatibility
by defining that a return value of EFI_SECURITY_VIOLATION would now
indicate that the image had been loaded and a valid image handle had
been created, but that the image should not be started.
The wording in version 2.2 is ambiguous, and does not define whether
or not a return value of EFI_SECURITY_VIOLATION indicates that a valid
image handle has been created.
Attempt to work around all of these incompatible and partially
undefined APIs by calling UnloadImage if we get a return value of
EFI_SECURITY_VIOLATION. Minimise the risk of passing an uninitialised
pointer to UnloadImage by setting ImageHandle to NULL prior to calling
LoadImage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the size of the USB disk image in the common case that
CONSOLE_INT13 is not enabled.
Originally-implemented-by: Romain Guyard <romain.guyard@mujin.co.jp>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Eliminate an unnecessary variable-length stack allocation and memory
copy by allowing TFTP option processors to modify the option string
in-place.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to UEFI specification 2.8 p 24.1 we must set the
EFI_SIMPLE_NETWORK_RECEIVE_MULTICAST bit in the "Disable" mask, when
"ResetMCastFilter" is TRUE.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Split-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Currently, if the SNP driver for whatever reason fails to enable
receive filters for multicast frames, it falls back to enabling just
unicast and broadcast filters. This breaks some IPv6 functionality as
the network card does not respond to neighbour solicitation requests.
Some cards refuse to enable EFI_SIMPLE_NETWORK_RECEIVE_MULTICAST, but
do support enabling EFI_SIMPLE_NETWORK_RECEIVE_PROMISCUOUS_MULTICAST,
so try it before falling back to just unicast+broadcast.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Split-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow a PeerDist hosted cache server to be specified via the
${peerhost} setting, e.g.:
# Use 192.168.0.1 as hosted cache server
set peerhost 192.168.0.1
Note that this simply treats the hosted cache server as a permanently
discovered peer for all segments.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the use of PeerDist content encoding to be enabled or disabled
via the ${peerdist} setting, e.g.:
# Disable PeerDist
set peerdist 0
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On devices with no EEPROM or OTP, the MAC_CR register defaults to not
using automatic link speed detection, with the result that no packets
are successfully sent or received.
Fix by always enabling automatic speed and duplex detection, since
iPXE provides no mechanism for manual configuration of either link
speed or duplex.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On at least some platforms (observed with a Raspberry Pi), any attempt
to perform USB transfers via EFI_USB_IO_PROTOCOL during EFI shutdown
will lock up the system. This is quite probably due to the already
documented failure of all EFI timers when ExitBootServices() is
called: see e.g. commit 5cf5ffea2 "[efi] Work around temporal anomaly
encountered during ExitBootServices()".
Work around this problem by refusing to poll endpoints if shutdown is
in progress, and by immediately failing any attempts to enqueue new
transfers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The USB core reuses the I/O buffer space occupied by the USB setup
packet to hold the completion status for message transfers, assuming
that the message() method will always strip the setup packet before
returning. This assumption is correct for all of the hardware
controller drivers (XHCI, EHCI, and UHCI), since these drivers are
able to enqueue the transfer as a separate action from waiting for the
transfer to complete.
The EFI_USB_IO_PROTOCOL does not allow us to separate actions in this
way: there is only a single blocking method that both enqueues and
waits for completion. Our usbio driver therefore currently defers
stripping the setup packet until the control endpoint is polled.
This causes a bug if a message transfer is enqueued but never polled
and is subsequently cancelled, since the cancellation will be reported
with the I/O buffer still containing the setup packet. This breaks
the assumption that the setup packet has been stripped, and triggers
an assertion failure in usb_control_complete().
Fix by always stripping the setup packet in usbio_endpoint_message(),
and adjusting usbio_control_poll() to match.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Ensure that the configured RSA digestInfo prefixes are included in any
build that includes rsa.o (rather than relying on x509.o or tls.o also
being present in the final binary).
This allows the RSA self-tests to be run in isolation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The restart of negotiation triggered by a HelloRequest currently does
not call tls_tx_resume() and so may end up leaving the connection in
an idle state in which the pending ClientHello is never sent.
Fix by calling tls_tx_resume() as part of tls_restart(), since the
call to tls_tx_resume() logically belongs alongside the code that sets
bits in tls->tx_pending.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Raw block downloads are expensive if the origin server uses HTTPS,
since each concurrent download will require local TLS resources
(including potentially large received encrypted data buffers).
Raw block downloads may also be prohibitively slow to initiate when
the origin server is using HTTPS and client certificates. Origin
servers for PeerDist downloads are likely to be running IIS, which has
a bug that breaks session resumption and requires each connection to
go through the full client certificate verification.
Limit the total number of concurrent raw block downloads to ameliorate
these problems.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move the responsibility for starting the block download timers from
peerblk_expired() to peerblk_raw_open() and peerblk_retrieval_open(),
in preparation for adding the ability to defer calls to
peerblk_raw_open() via a block download queue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a build shortcut "rpi", allowing for e.g.
make CONFIG=rpi CROSS=aarch64-linux-gnu- bin-arm64-efi/rpi.efi
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The (very approximate) split between Makefile.housekeeping and
Makefile is that the former provides mechanism and the latter provides
policy.
Provide a section within Makefile as a home for predefined build
shortcuts such as the existing all-drivers build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The WORKAROUND_CFLAGS list is constructed based on running tests on
the target compiler, and the results may not be valid for the host
compiler.
The only relevant workaround required for the host compiler is
-Wno-stringop-truncation, which is needed to avoid a spurious compiler
warning for a totally correct usage of strncpy() in util/elf2efi.c.
Duplicating the workaround tests for the host compiler is messy, as is
conditionally applying __attribute__((nonstring)). Fix instead by
disapplying WORKAROUND_CFLAGS for the host compiler, and using
memcpy() with an explicitly calculated length instead of strncpy() in
util/elf2efi.c.
Reported-by: Ignat Korchagin <ignat@cloudflare.com>
Reported-by: Christopher Clark <christopher.w.clark@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Compiling with gcc 9.1 generates lots of "taking address of packed
member of ... may result in an unaligned pointer value" warnings.
Some of these warnings are genuine, and indicate correctly that parts
of iPXE currently require the CPU (or runtime environment) to support
unaligned accesses. For example: the TCP/IP receive data path will
attempt to access 32-bit fields that may not be aligned to a 32-bit
boundary.
Other warnings are either spurious (such as when the pointer is to a
variable-length byte array, which can have no alignment requirement
anyway) or unhelpful (such as when the pointer is used solely to
provide a debug colour value for the DBGC() macro).
There appears to be no easy way to silence the spurious warnings.
Since the ability to perform unaligned accesses is already a
requirement for iPXE, work around the problem by silencing this class
of warnings.
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use '%p' directive, and print handle's address if the address is null
and the handle doesn't have a name. This fixes the following
compilation error:
interface/efi/efi_debug.c:334:3: error: '%s' directive
argument is null [-Werror=format-overflow=]
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Raspberry Pi NIC has no EEPROM to hold the MAC address. The
platform firmware (e.g. UEFI or U-Boot) will typically obtain the MAC
address from the VideoCore firmware and add it to the device tree,
which is then made available to subsequent programs such as iPXE or
the Linux kernel.
Add the ability to parse a flattened device tree and to extract the
MAC address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
efidev_parent() currently assumes that any device with BUS_TYPE_EFI is
part of a struct efi_device. This assumption is not valid, since the
code in efi_device_info() may also create a device with BUS_TYPE_EFI.
Fix by searching through the list of registered EFI devices when
looking for a match, instead of relying on the bus type value.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It is currently not possible to build the all-drivers iPXE binaries
for ARM, since there is no implementation for inb(), outb(), etc.
There is no common standard for accessing I/O space on ARM platforms,
and there are almost no ARM-compatible peripherals that actually
require I/O space accesses.
Provide dummy implementations that behave as though no device is
present (i.e. ignore writes, return all bits high for reads). This is
sufficient to allow the all-drivers binaries to link, and should cause
drivers to behave as though no I/O space peripherals are present in
the system.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 1a7746603 ("[build] Fix use of inline assembly on GCC 4.8 ARM64
builds") switched from using "%c0" to "%a0" in order to avoid an
"invalid operand prefix" error on the ARM64 version of GCC 4.8.
It appears that the ARM64 version of GCC 8 now produces an "invalid
address mode" error for the "%a0" form, but is happy with the original
"%c0" form.
Switch back to using the "%c0" form, on the assumption that the
requirement for "%a0" was a temporary aberration.
Originally-fixed-by: John L. Jolly <jjolly@suse.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function defaults to operating in "PXE mode" after a
power-on reset. In this mode, receive descriptors are fetched and
written back as single descriptors. In normal (non-PXE mode)
operation, receive descriptors are fetched and written back only as
complete cachelines unless an interrupt is raised.
There is no way to return to PXE mode from non-PXE mode, and there is
no way for the virtual function driver to operate in PXE mode.
Choose to operate in non-PXE mode. This requires us to trick the
hardware into believing that it is raising an interrupt, so that it
will not defer writing back receive descriptors until a complete
cacheline (i.e. four packets) have been consumed. We do so by
configuring the hardware to use MSI-X with a dummy target location in
place of the usual APIC register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The virtual function driver will use the same transmit and receive
descriptor ring structures, but will not itself construct and program
the ring context. Split out ring creation and destruction from the
programming of the ring context, to allow code to be shared between
physical and virtual function drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The virtual function transmit and receive ring tail register offsets
do not match those of the physical function. Allow the tail register
offsets to be specified separately.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function driver does not allow the virtual function to
request the use of 16-byte receive descriptors. Switch to using
32-byte receive descriptors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a weak stub function for handling the "send to VF" event used
for communications between the physical and virtual function drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "send to PF" and "send to VF" admin queue descriptors (ab)use the
cookie field to hold the extended opcode and return code values.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A virtual function reset is triggered via an admin queue command and
will reset the admin queue configuration registers. Allow the admin
queues to be reinitialised after such a reset, without requiring the
overhead (and potential failure paths) of freeing and reallocating the
queues.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently use a single data buffer shared between all admin queue
descriptors. This works for the physical function driver since we
have at most one command in progress and only a single event (which
does not use a data buffer).
The communication path between the physical and virtual function
drivers uses the event data buffer, and there is no way to prevent a
solicited event (i.e. a response to a request) from being overwritten
by an unsolicited event (e.g. a link status change).
Provide individual data buffers for each admin event queue descriptor
(and for each admin command queue descriptor, for the sake of
consistency).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The register map for the virtual functions appears to have been
constructed using a random number generator.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function driver does not allow the virtual function to
request that VLAN tags are left unstripped. Extract and use the VLAN
tag from the receive descriptor if present.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Hermon driver uses vlan_find() to identify the appropriate VLAN
device for packets that are received with the VLAN tag already
stripped out by the hardware. Generalise this capability and expose
it for use by other network card drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel 40 Gigabit Ethernet virtual functions support only MSI-X
interrupts, and will write back completed interrupt descriptors only
when the device attempts to raise an interrupt (or when a complete
cacheline of receive descriptors has been completed).
We cannot actually use MSI-X interrupts within iPXE, since we never
have ownership of the APIC. However, an MSI-X interrupt is
fundamentally just a DMA write of a single dword to an arbitrary
address. We can therefore configure the device to "raise" an
interrupt by writing a meaningless value to an otherwise unused memory
location: this is sufficient to trigger the receive descriptor
writeback logic.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
One of the design goals of ASN.1 DER is to provide a canonical
serialization of a data structure, thereby allowing for equality of
values to be tested by simply comparing the serialized bytes.
Some OCSP servers will modify the request certID to omit the optional
(and null) "parameters" portion of the hashAlgorithm. This is
arguably legal but breaks the ability to perform a straightforward
bitwise comparison on the entire certID field between request and
response.
Fix by comparing the OID-identified hashAlgorithm separately from the
remaining certID fields.
Originally-fixed-by: Thilo Fromm <Thilo@kinvolk.io>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide increased visibility into the progress of TCP connections by
displaying an explicit "connecting" status message while waiting for
the TCP handshake to complete.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TLS connections will almost always create background connections to
perform cross-signed certificate downloads and OCSP checks. There is
currently no direct visibility into which checks are taking place,
which makes troubleshooting difficult in the absence of either a
packet capture or a debug build.
Use the job progress message buffer to report the current cross-signed
certificate download or OCSP status check, where applicable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Record the session ID (if any) provided by the server and attempt to
reuse it for any concurrent connections to the same server.
If multiple connections are initiated concurrently (e.g. when using
PeerDist) then defer sending the ClientHello for all but the first
connection, to allow time for the first connection to potentially
obtain a session ID (and thereby speed up the negotiation for all
remaining connections).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a Dell OptiPlex 7010, calling DisconnectController() on the LOM
device handle will lock up the system. Debugging shows that execution
is trapped in an infinite loop that is somehow trying to reconnect
drivers (without going via ConnectController()).
The problem can be reproduced in the UEFI shell with no iPXE code
present, by using the "disconnect" command. Experimentation shows
that the only fix is to unload (rather than just disconnect) the
"Ip4ConfigDxe" driver.
Add the concept of a blacklist of UEFI drivers that will be
automatically unloaded when iPXE runs as an application, and add the
Dell Ip4ConfigDxe driver to this blacklist.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Option::ROM module recognizes and checks EFI header of image. The
disrom.pl utility dumps this header if is present.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Option::ROM module now compares the Code Type in the PCIR header
to 0x00 (PC-AT) in order to check the presence of other header types
(PnP, UNDI, iPXE, etc). The validity of these headers are checked not
only by offset, but by range and signature checks also. The image
checksum and initial size also depends on Code Type.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
GCC 9 warns that abs() may truncate its signed long argument. Fix by
using labs() instead.
Reported-by: Martin Liška <mliska@suse.cz>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Fix strcmp() and strncmp() to return proper standard positive/negative
values for unequal strings. Current implementation is backwards
(i.e. the functions are returning negative when should be positive and
vice-versa).
Currently all consumers of these functions only check the return value
for ==0 or !=0 and so we can safely change the implementation without
breaking things.
Signed-off-by: Aaron Young <Aaron.Young@oracle.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Current (simplified):
1. InstallMultipleProtocolInterfaces
if err goto err_install_protocol_interface;
2. OpenProtocol(efi_nii_protocol_guid)
if err goto err_open_nii;
3. OpenProtocol(efi_nii31_protocol_guid)
if err goto err_open_nii31;
4. efi_child_add
if err goto err_efi_child_add;
...
err_efi_child_add:
CloseProtocol(efi_nii_protocol_guid) <= should be efi_nii31_protocol_guid
err_open_nii: <= should be err_open_nii31
CloseProtocol(efi_nii31_protocol_guid) <= should be efi_nii_protocol_guid
err_open_nii31: <= should be err_open_nii
UninstallMultipleProtocolInterfaces
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PCI Configuration Space contains fields prog-if at the offset 0x09,
sub-class at the offset 0x0a and base-class at the offset 0x0b (it
respects little endian). PCIR structure uses these fields in the same
order.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Starting from binutils 2.31.0 (commit bd7ab16b) x86-64 assembler
generates R_X86_64_PLT32 instead of R_X86_64_PC32.
Acked-by: John Jolly <jjolly@suse.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The first adapters in this family are X2522-10, X2522-25, X2541 and
X2542.
These no longer use PCI BAR 0 for I/O, but use that for memory. In
other words, BAR 2 on SFN8xxx adapters now becomes BAR 0.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Devices that support jumbo frames will currently default to the
largest possible MTU. This assumption is valid for virtual adapters
such as virtio-net, where the MTU must have been configured by a
system administrator, but is unsafe in the general case of a physical
adapter.
Default to the standard Ethernet MTU, unless explicitly overridden
either by the driver or via the ${netX/mtu} setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid calling rndis_halt() and rndis->op->close() twice if the call to
register_netdev() fails.
Reported-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of gcc seem to silently accept an attempt to disable an
unrecognised warning (e.g. via -Wno-stringop-truncation) but will then
report the unrecognised warning if any other error occurs during the
build, resulting in a potentially misleading error message.
Avoid this potential confusion by using the positive-form tests in
order to determine the workaround CFLAGS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The definition of version_response channel message in Linux doesn't
include version field, so the upcoming VMBus implementation in QEMU
doesn't set it either. Neither Windows nor Linux had any problem with
this.
The check against this field is redundant because the message is the
response to initiate_contact message containing the specific version
requested, so the response with version_supported=true is unambiguous.
Drop this check and don't rely on the field to be present in the
message.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
register_netdev expects ->hw_addr and ->ll_addr to be already filled,
so move it towards the end of register_rndis, after the respective
fields have been successfully queried from the underlying device.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The gcc 8 compiler introduces a warning for certain string
manipulation functions, flagging usages which _may_ not be intended.
An audit of the iPXE sources indicates all usages of strncat and
strncpy are as intended, so the warnings currently issued are not
helpful, especially if warnings are considered errors.
Fix by detecting gcc's support for -Wno-stringop-truncation and, if
detected, using that option to avoid the warning.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Also-fixed-by: Christian Hesse <list@eworm.de>
Also-fixed-by: Roman Kagan <rkagan@virtuozzo.com>
Also-fixed-by: Bernhard M. Wiedemann <bwiedemann@suse.de>
Also-fixed-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As pointedly documented in RFC7230 section 2.3, HTTP is a stateless
protocol: each request message can be understood in isolation from any
other requests or responses. Various authentication schemes such as
NTLM break this fundamental property of HTTP and rely on the same TCP
connection being reused.
Work around these broken authentication schemes by ensuring that the
most recently pooled connection is reused for the subsequent
authentication retry.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Tested-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the function mii_find() in order to locate the PHY address.
Signed-off-by: Sylvie Barlow <sylvie.c.barlow@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently have no generic concept of a PHY address, since all
existing implementations simply hardcode the PHY address within the
MII access methods.
A bit-bashing MII interface will need to be provided with an explicit
PHY address in order to generate the correct waveform. Allow for this
by separating out the concept of a MII device (i.e. a specific PHY
address attached to a particular MII interface).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the subsystem IDs to be used when checking for PXE stacks with
broken interrupt support.
Suggested-by: Levi Hsieh <Levi.Hsieh@dell.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The relocation type R_ARM_REL32 is generated when building
bin-arm32-efi/snp.efi using gcc 6.3 and ld 2.28.
R_ARM_REL32 is a program counter (PC) relative 32 bit relocation so we
can ignore it like all other PC relative relocations.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When booting some versions of the UEFI shell, our driver binding
protocol's Supported() entry point is called at TPL_NOTIFY for no
discernible reason. Attempting to raise to TPL_CALLBACK triggers an
immediate assertion failure in the firmware.
Since our Supported() method can run at any TPL, fix by simply not
attempting to raise the TPL within this method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Release SNP devices to allow the SAN booted image to use our
EFI_SIMPLE_NETWORK_PROTOCOL instance, and to ensure that the image is
started at TPL_APPLICATION.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The cipherstream xfer_window_changed() message is used to retrigger
the TLS transmit state machine. If the transmit state machine is
idle, then the window change message will not be propagated to the
plainstream interface. This can potentially cause the plainstream
interface peer (e.g. httpcore) to block waiting for a window change
message that will never arrive.
Fix by ensuring that the window change message is propagated to the
plainstream interface if the transmit state machine is idle. (If the
transmit state machine is not idle then the plainstream window will be
zero anyway.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In TLS terminology a session conceptually spans multiple individual
connections, and essentially represents the stored cryptographic state
(master secret and cipher suite) required to establish communication
without going through the certificate and key exchange handshakes.
Rename tls_session to tls_connection in order to make the name
tls_session available to represent the session state.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A failure in tls_generate_random() will result in a call to ref_put()
before the received data list has been initialised, which will cause
free_tls() to attempt to traverse an uninitialised list.
Fix by ensuring that all fields referenced by free_tls() are
initialised before any of the potential failure paths.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 6149e0a ("[librm] Provide symbols for inline code placed into
other sections") may cause build failures due to duplicate label names
if the compiler chooses to duplicate inline assembly code.
Fix by using the "%=" special format string to include a
guaranteed-unique number within the label name.
The "%=" will be expanded only if constraints exist for the inline
assembly. This fix therefore requires that all REAL_CODE() fragments
use a (possibly empty) constraint list.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide symbols constructed from the object name and line number for
code fragments placed into alternative sections, such as inline
REAL_CODE() assembly placed into .text16. This simplifies the
debugging task of finding the source code corresponding to a given
instruction pointer.
Note that we cannot use __FUNCTION__ since it is not a preprocessor
macro and so cannot be concatenated with string literals.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the underlying PXE stack reports an invalid IRQ number (above
IRQ_MAX), treat this as equivalent to an empty IRQ number and fall
back to using polling mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The existence of MMX and SSE is required by the System V x86_64 ABI
and so is assumed by gcc, but these registers are not preserved by our
own interrupt handlers and are unlikely to be preserved by other
context switch handlers in a boot firmware environment.
Explicitly prevent gcc from using MMX or SSE registers to avoid
potential problems due to silent register corruption.
We must remove the %xmm0-%xmm5 clobbers from the x86_64 version of
hv_call() since otherwise gcc will complain about unknown register
names. Theoretically, we should probably add code to explicitly
preserve the %xmm0-%xmm5 registers across a hypercall, in order to
guarantee to external code that these registers remain unchanged. In
practice this is difficult since SSE registers are disabled by
default: for background information see commits 71560d1 ("[librm]
Preserve FPU, MMX and SSE state across calls to virt_call()") and
dd9a14d ("[librm] Conditionalize the workaround for the Tivoli VMM's
SSE garbling").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently perform various min-entropy calculations using build-time
floating-point arithmetic. No floating-point code ends up in the
final binary, since the results are eventually converted to integers
and asserted to be compile-time constants.
Though this mechanism is undoubtedly cute, it inhibits us from using
"-mno-sse" to prevent the use of SSE registers by the compiler.
Fix by using fixed-point arithmetic instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This is required to work around a bug in some firmware versions.
Signed-off-by: Ameer Mahagneh <ameerm@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the ACPI power management timer to be used if enabled via
TIMER_ACPI in config/timer.h. This provides an alternative timer on
systems where the standard 8254 PIT is unavailable or unreliable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some drivers are known to call the optional Map_Mem() callback without
first checking that the callback exists. Provide a usable basic
implementation of Map_Mem() along with the other callbacks that become
mandatory if Map_Mem() is provided.
Note that in theory the PCI I/O protocol is allowed to require
multiple calls to Map(), with each call handling only a subset of the
overall mapped range. However, the reference implementation in EDK2
assumes that a single Map() will always suffice, so we can probably
make the same simplifying assumption here.
Tested with the Intel E3522X2.EFI driver (which, incidentally, fails
to cleanly remove one of its mappings).
Originally-implemented-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The blocked link test in eth_slow_lacp_rx() is performed before the
actor TLV is copied to the partner TLV, and so must test the actor
state field rather than the partner state field.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some CAs provide non-functional OCSP servers, and some clients are
forced to operate on networks without access to the OCSP servers.
Allow the user to explicitly disable the use of OCSP checks by
undefining OCSP_CHECK in config/crypto.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Limit the profile sample count to INT_MAX to avoid both signed
overflow and a potential division by zero when updating the stored
mean value.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Mark the link as blocked if the LACP partner is not reporting itself
as being in sync, collecting, and distributing.
This matches the behaviour for STP: we mark the link as blocked if we
detect that the switch is actively blocking traffic, in order to
extend the DHCP discovery period and so prevent boot failures on
switches that take an excessively long time to enable ports.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the global variable shomron_nodnic_supported, since it may have
different values for different PCI devices.
Originally-fixed-by: Mohammed Taha <mohammedt@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When DEBUG=librm_mgmt is enabled, intercept CPU exceptions and provide
a register and stack dump, then drop to an emergency shell. Exiting
from the shell will almost certainly not work, but this provides an
opportunity to view the register and stack dump and carry out some
basic debugging.
Note that we can intercept only the first 8 CPU exceptions, since a
PXE ROM is not permitted to rebase the PIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Bruce Rogers
Joseph Wong
Ignat Korchagin
Valentine Barshak
Mohammed
Christian Nilsson
Petr Borsodi
Aaron Young
Christian Hesse
Martin Habets
Roman Kagan
Rob Taglang
Steven Haber
Sylvie Barlow
Rob Taglang
Heinrich Schuchardt
Robin Smidsrød
Ameer Mahagneh