The first adapters in this family are X2522-10, X2522-25, X2541 and
X2542.
These no longer use PCI BAR 0 for I/O, but use that for memory. In
other words, BAR 2 on SFN8xxx adapters now becomes BAR 0.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Devices that support jumbo frames will currently default to the
largest possible MTU. This assumption is valid for virtual adapters
such as virtio-net, where the MTU must have been configured by a
system administrator, but is unsafe in the general case of a physical
adapter.
Default to the standard Ethernet MTU, unless explicitly overridden
either by the driver or via the ${netX/mtu} setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the function mii_find() in order to locate the PHY address.
Signed-off-by: Sylvie Barlow <sylvie.c.barlow@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently have no generic concept of a PHY address, since all
existing implementations simply hardcode the PHY address within the
MII access methods.
A bit-bashing MII interface will need to be provided with an explicit
PHY address in order to generate the correct waveform. Allow for this
by separating out the concept of a MII device (i.e. a specific PHY
address attached to a particular MII interface).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This is required to work around a bug in some firmware versions.
Signed-off-by: Ameer Mahagneh <ameerm@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some drivers are known to call the optional Map_Mem() callback without
first checking that the callback exists. Provide a usable basic
implementation of Map_Mem() along with the other callbacks that become
mandatory if Map_Mem() is provided.
Note that in theory the PCI I/O protocol is allowed to require
multiple calls to Map(), with each call handling only a subset of the
overall mapped range. However, the reference implementation in EDK2
assumes that a single Map() will always suffice, so we can probably
make the same simplifying assumption here.
Tested with the Intel E3522X2.EFI driver (which, incidentally, fails
to cleanly remove one of its mappings).
Originally-implemented-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the global variable shomron_nodnic_supported, since it may have
different values for different PCI devices.
Originally-fixed-by: Mohammed Taha <mohammedt@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reporting a completion via usb_complete() will pass control outside
the scope of xhci.c, and could potentially result in a further call to
xhci_event_poll() before returning from usb_complete(). Since we
currently update the event consumer counter only after calling
usb_complete(), this can result in duplicate completions and
consequent corruption of the submission TRB ring structures.
Fix by updating the event ring consumer counter before passing control
to usb_complete().
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Tested-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The i219 appears to have a seriously broken reset mechanism. After
any transmit or receive activity, resetting the card will break both
the transmit and receive datapaths until the next PCI bus reset.
The Linux and BSD drivers include a convoluted workaround authored by
Intel which involves setting a bit in the undocumented FEXTNVM11
register, then transmitting a dummy 512-byte packet containing garbage
data, then reconfiguring the receive descriptor prefetch thresholds
and temporarily reenabling the receive datapath. The comments in the
Intel fix do not even remotely match what the code actually does, and
the code accidentally leaves the transmitter enabled after use.
Experimentation suggests that an equivalent fix is to simply set the
undocumented bit in FEXTNVM11 before enabling the transmit or receive
descriptor rings.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Invalid protocol speed ID tables appear to be increasingly common in
the wild, to the point that it is infeasible to apply an explicit
XHCI_BAD_PSIV flag for each offending PCI device ID.
Fix by assuming an invalid PSI table as soon as any invalid value is
reported by the hardware.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of gcc (observed with gcc 4.7.2) report a spurious
uninitialised variable warning in ena_get_device_attributes(). Work
around this warning by manually inlining the relevant code (which has
only a single call site).
Reported-by: xbgmsharp <xbgmsharp@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most drivers do not utilise an MII interface, since the link state is
typically available directly from a memory-mapped register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The SnpDxe driver raises the task priority level to TPL_CALLBACK when
calling the UNDI entry point. This does not appear to be a documented
requirement, but we should probably match the behaviour of SnpDxe to
minimise surprises to third party code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The tap driver can retrieve a potentially unlimited number of packets
in a single poll. This can lead to heap exhaustion under heavy load.
Fix by imposing an artificial receive quota (as already used in other
drivers without natural receive limits).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification has an implicit and demonstrably incorrect
requirement (in the Mem_IO() calling convention) that any UNDI network
device has at most one memory BAR and one I/O BAR.
Some UEFI platforms have been observed to report the existence of
non-existent additional I/O BARs, causing iPXE to select the wrong
BAR. This problem does not affect the SnpDxe driver, since that
driver will always choose the lowest numbered existent BAR of each
type.
Adjust iPXE's behaviour to match that of SnpDxe, i.e. to always select
the lowest numbered BAR(s).
Debugged-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Debugged-by: Adklei <adklei@realtek.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The LAN78xx datapath is essentially identical to that of the SMSC75xx.
Expose the transmit, poll, and bulk IN endpoint operations to allow
for reuse by the LAN78xx driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The LAN78xx PHY interrupt source and mask registers do not match those
used by the SMSC75xx and SMSC95xx.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since we don't enable IOMMU at all, we can then simply enable the
IOMMU support by claiming the support of VIRITO_F_IOMMU_PLATFORM.
This fixes booting failure when iommu_platform is set from qemu cli.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The smsc75xx and smsc95xx drivers include a substantial amount of
identical functionality, varying only in the base address of register
sets. Abstract out this common functionality to allow code to be
shared between the drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently use a zero language ID to retrieve strings such as the
ECM/NCM MAC address. This works on most hardware devices, but is
known to fail on some software emulated CDC-NCM devices.
Fix by using the first supported language ID, falling back to English
(0x0409) if any error occurs when fetching the list of supported
languages. This matches the behaviour of the Linux kernel.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Xen network backend (xen-netback) suffered from a regression
between upstream Linux kernels 3.18 and 4.2 inclusive, which would
cause packet reception to fail unless at least 18 receive buffers were
available. This bug was fixed in kernel commit 1d5d485 ("xen-netback:
require fewer guest Rx slots when not using GSO").
Work around this bug in affected versions of xen-netback by providing
the requisite 18 receive buffers.
Reported-by: Taylor Schneider <tschneider@live.com>
Tested-by: Taylor Schneider <tschneider@live.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 7cfdd76 ("[block] Describe all SAN devices via ACPI tables")
changed the definition of the iSCSI initiator IQN in the iBFT to
represent a common initiator IQN used for all iSCSI sessions, and
attempted to calculate this common initiator IQN by fetching the
common ${initiator-iqn} setting.
This fails when no explicit ${initiator-iqn} has been specified
(i.e. when an initiator IQN has instead been constructed from either
the hostname or system UUID), and results in an empty initiator IQN in
the iBFT.
Fix by using the initiator IQN of an arbitrary iSCSI session
present in the iBFT.
Debugged-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An "enlightened" external bootloader (such as Windows Server 2016's
winload.exe) may take ownership of the Hyper-V connection before all
INT 13 operations have been completed. When this happens, all VMBus
devices are implicitly closed and we are left with a non-functional
network connection.
Detect when our Hyper-V connection has been lost (by checking the
SynIC message page MSR). Reclaim ownership of the Hyper-V connection
and reestablish any VMBus devices, without disrupting any existing
iPXE state (such as IPv4 settings attached to the network device).
Windows Server 2016 will not cleanly take ownership of an active
Hyper-V connection. Experimentation shows that we can quiesce by
resetting only the SynIC message page MSR; this results in a
successful SAN boot (on a Windows 2012 R2 physical host). Choose to
quiesce by resetting (almost) all MSRs, in the hope that this will be
more robust against corner cases such as a stray synthetic interrupt
occurring during the handover.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On most Intel NICs, Auto-Speed Detection Enable (ASDE) can be used to
automatically detect the correct link speed by sampling the link using
the internal PHY. This feature is automatically inhibited when not
appropriate for the physical link (e.g. when using internal SerDes
mode on the 8254x).
On the i350 datasheet ASDE is a reserved bit, but the relevant
auto-speed detection hardware appears still to be present. However,
enabling ASDE on the i350 1000BASE-KX backplane NIC seems to cause an
immediate link failure. It is possible that the auto-speed detection
hardware is still present, is not connected to a physical link, and is
not inhibited from being applied in this mode.
Work around this problem by adding an INTEL_NO_ASDE flag bit
(analogous to INTEL_NO_PHY_RST), and applying this for the i350
backplane NIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In situations where iPXE fails to reach link-up as expected, it is
useful to know the original values of the CTRL and STATUS registers
prior to our reset attempt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Martin Habets
Michael Brown
Steven Haber
Sylvie Barlow
Rob Taglang
Ameer Mahagneh
Joseph Wong
Janos Mattyasovszky
Peter von Konigsmark
Richard Moore
Jason Wang
Jerone Young
Mika Tiainen