Some protocols (such as ARP) may modify the received packet and re-use
the same I/O buffer for transmission of a reply. The SMSC95XX
transmit header is larger than the receive header: the re-used I/O
buffer therefore does not have sufficient headroom for the transmit
header, and the ARP reply will therefore fail to be transmitted. This
is essentially the same problem as in commit 2e72d10 ("[ncm] Reserve
headroom in received packets").
Fix by reserving sufficient space at the start of each received packet
to allow for the difference between the lengths of the transmit and
receive headers.
This problem is not caught by the current driver development test
suite (documented at http://ipxe.org/dev/driver), since even the large
file transfer tests tend to completely sufficiently quickly that there
is no need for the server to ever send an ARP request. The failure
shows up only when using a very slow protocol such as RFC7440-enhanced
TFTP (as used by Windows Deployment Services).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The LED pins are configured by default as GPIO inputs. While it is
conceivable that a board might actually use these pins as GPIOs, no
such board is known to exist.
The Linux smsc95xx driver configures these pins unconditionally as LED
outputs. Assume that it is safe to do likewise.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the network interface name (e.g. "net0") as a setting. This
allows a script to obtain the name of the most recently opened network
interface via ${netX/ifname}.
Signed-off-by: Andrew Widdersheim <amwiddersheim@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a named CONFIG=cloud configuration, which enables console types
useful for obtaining output from virtual machines in public clouds
such as AWS EC2.
An image suitable for use in AWS EC2 can be built using
make bin/ipxe.usb CONFIG=cloud EMBED=config/cloud/aws.ipxe
The embedded script will direct iPXE to download and execute the EC2
"user-data" file, which is always available to an EC2 VM via the URI
http://169.254.169.254/latest/user-data (regardless of the VPC
networking settings). The boot can therefore be controlled by
modifying the per-instance user data, without having to modify the
boot disk image.
Console output can be obtained via syslog (with a syslog server
configured in the user-data script), via the AWS "System Log" (after
the instance has been stopped), or as a last resort from the log
partition on the boot disk.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The three nominally-disambiguated ENOTSUP errors accidentally all used
the same error disambiguator, rendering them identical. Fix by
changing all three values. We avoid reusing the 0x01 disambiguator
value, since that remains ambiguous in older binaries.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some BIOS console redirection capabilities do not work well with the
colourised debug messages used by iPXE. We already allow the range of
colours to be controlled via the DBGCOL=... build parameter. Extend
this syntax to allow DBGCOL=0 to be used to mean "disable colours".
Requested-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a debug function check_bios_interrupts() to look for changes
to the interrupt vector table. This can be useful when investigating
the behaviour (including crashes) of external PXE NBPs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For historical reasons, iPXE sets the current working URI to the root
of the TFTP server whenever the TFTP server address is changed. This
was originally implemented in the hope of allowing a DHCP-provided
TFTP filename to be treated simply as a relative URI. This usage
turns out to be impractical since DHCP-provided TFTP filenames may
include characters which would have special significance to the URI
parser, and so the DHCP next-server+filename combination is now
handled by the dedicated pxe_uri() function instead.
The practice of setting the current working URI to the root of the
TFTP server is potentially helpful for interactive uses of iPXE,
allowing a user to type e.g.
iPXE> dhcp
Configuring (net0 52:54:00:12:34:56)... ok
iPXE> chain pxelinux.0
and have the URI "pxelinux.0" interpreted as being relative to the
root of the TFTP server provided via DHCP.
The current implementation of tftp_apply_settings() has an unintended
flaw. When the "dhcp" command is used to renew a DHCP lease (or to
pick up potentially modified DHCP options), the old settings block
will be unregistered before the new settings block is registered.
This causes tftp_apply_settings() to believe that the TFTP server has
been changed twice (to 0.0.0.0 and back again), and so the current
working URI will always be set to the root of the TFTP server, even if
the DHCP response provides exactly the same TFTP server as previously.
Fix by doing nothing in tftp_apply_settings() whenever there is no
TFTP server address.
Debugged-by: Andrew Widdersheim <awiddersheim@inetu.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Update the image's recorded URI when a download redirection occurs.
This ensures that URIs relative to a redirected download are resolved
correctly.
In particular, this allows for the use of relative URIs in scripts
that are themselves downloaded via a redirection, such as the HTTP 301
redirection used to fix up URIs pointing to directories but omitting
the trailing slash (e.g. "http://boot.ipxe.org/demo", which will be
redirected to "http://boot.ipxe.org/demo/").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Resolve redirection URIs as being relative to the original HTTP
request URI, rather than treating them as being implicitly relative to
the current working URI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5de45cd ("[romprefix] Report a pessimistic runtime size
estimate") set the PCI3.0 "runtime size" field equal to the worst-case
runtime size, on the basis that there is no guarantee that PMM
allocation will succeed and hence no guarantee that we will be able to
shrink the ROM image.
On a PCI3.0 system where PMM allocation would succeed, this can cause
the BIOS to unnecessarily refuse to initialise the iPXE ROM due to a
perceived shortage of option ROM space.
Fix by reporting the best-case runtime size via the PCI header, and
checking that we have sufficient runtime space (if applicable). This
allows iPXE ROMs to initialise on PCI3.0 systems that might otherwise
fail due to a shortage of option ROM space.
This may cause iPXE ROMs to fail to initialise on PCI3.0 systems where
PMM is broken. (Pre-PCI3.0 systems are unaffected since there must
already have been sufficient option ROM space available for the
initialisation entry point to be called.)
On balance, it seems preferable to avoid breaking "good" systems
(PCI3.0 with working PMM) at the cost of potentially breaking "bad"
systems (PCI3.0 with broken PMM).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The GuestRPC mechanism (used for VMWARE_SETTINGS and CONSOLE_VMWARE)
does not use any real-mode code and so can be exposed in both 64-bit
and 32-bit builds.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the use of the iPXE DRBG implementation in BSD-licensed
projects.
Requested-by: Sean Davis <dive@hq.endersgame.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the use of the iPXE DRBG implementation in BSD-licensed
projects.
Requested-by: Sean Davis <dive@hq.endersgame.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The SMSC95xx devices tend to be used in embedded systems with a
variety of ad-hoc mechanisms for storing the MAC address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When USB network card drivers are used, the BIOS' legacy USB
capability is necessarily disabled since there is no way to share the
host controller between the BIOS and iPXE.
Commit 3726722 ("[usb] Add basic support for USB keyboards") added
support allowing a USB keyboard to be used within iPXE. However,
external code such as a PXE NBP has no way to utilise this support,
and so a USB keyboard cannot be used to control a PXE NBP loaded from
a USB network card.
Add support for injecting keypresses from any iPXE console into the
BIOS keyboard buffer. This allows external code such as a PXE NBP to
function with a USB keyboard even after the BIOS' legacy USB
capability has been disabled.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The build system allows for additional drivers (or other objects) to
be specified using build targets such as
make bin/intel--realtek.usb
make bin/8086100e--8086100f.mrom
This currently fails if the base target is the "bin/ipxe.*" all-drivers
target, e.g.
make bin/ipxe--acm.usb
Fix the build target parsing logic to allow additional drivers (or
other objects) to be included on top of the base all-drivers target.
This can be used to include USB network card drivers, which are not
yet included by default in the all-drivers build.
Reported-by: Andrew Sloma <asloma@lenovo.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some xHCI controllers (such as qemu's emulated xHCI controller) do not
correctly handle zero-length packets that are part of a TRB chain.
The zero-length TRB ends up being squashed and does not result in a
zero-length packet as seen by the device.
Work around this problem by marking the zero-length packet as
belonging to a separate transfer descriptor.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some hubs (e.g. the Avocent Corp. Virtual Hub on a Lenovo x3550
Integrated Management Module) have been observed to require more than
the standard 200ms for ports to stabilise, with the result that
devices appear to disconnect and immediately reconnect during the
initial bus enumeration.
Work around this problem by allowing specific hubs an extra 500ms of
settling time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Record the speed of a USB device based on the port's speed at the time
that the device was enabled. This allows us to remember the device's
speed even after the device has been disconnected (and so the port's
current speed has changed).
In particular, this allows us to correctly identify the transaction
translator for a low-speed or full-speed device after the device has
been disconnected.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The usb_message() and usb_stream() functions currently check for
port->speed==USB_SPEED_NONE to determine whether or not a device has
been unplugged. This test will give a false negative result if a new
device has been plugged in before the hotplug mechanism has finished
handling the removal of the old device.
Fix by checking instead the port->disconnected flag, which is now
cleared only after completing the removal of the old device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide BIT_QWORD_PTR() to allow for easy extraction of non-endian
fields (e.g. Infiniband GUIDs) without unnecessary byte swapping.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Tested using QEMU and usbredir to expose the LAN9512 chip present on a
Raspberry Pi.
There is a known issue with the LAN9512: an extra two bytes are
appended to every transmitted packet. These two bytes comprise:
{ 0x00, 0x08 } if packet length == 0 (mod 8)
{ CRC[0], 0x00 } if packet length == 7 (mod 8)
{ CRC[0], CRC[1] } otherwise
The extra bytes are appended whether the Ethernet CRC is generated
manually or added automatically by the hardware. The issue occurs
with the Linux kernel driver as well as the iPXE driver. It appears
to be an undocumented hardware errata.
TCP/IP traffic is not affected, since the IP header length field
causes the extraneous bytes to be discarded by the receiver. However,
protocols that rely on the length of the Ethernet frame (such as FCoE
or iPXE's "lotest" protocol) will be unusable on this hardware.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some models (notably ICH), the PHY reset mechanism appears to be
broken. In particular, the PHY_CTRL register will be correctly loaded
from NVM but the values will not be propagated to the "OEM bits" PHY
register. This typically has the effect of dropping the link speed to
10Mbps.
Since the original version of this driver in commit 945e428 ("[intel]
Replace driver for Intel Gigabit NICs"), we have always worked around
this problem by skipping the PHY reset if the link is already up.
Enhance this workaround by explicitly checking for known-broken PCI
IDs.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE does not call shutdown() before invoking a COMBOOT executable,
since the executable is allowed to make API calls back into iPXE. If
a background picture is used, then the console will not be restored to
text mode before invoking the COMBOOT executable. This can cause
undefined behaviour.
Fix by adding an explicit call to console_reset() immediately before
invoking a COMBOOT or COM32 executable, analogous to the call made to
console_reset() immediately before invokving a PXE NBP.
Debugged-by: Andrew Widdersheim <awiddersheim@inetu.net>
Tested-by: Andrew Widdersheim <awiddersheim@inetu.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For switches which remain permanently in the non-forwarding state (or
which erroneously report a non-forwarding state), ensure that iPXE
will eventually give up waiting for the link to become unblocked.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If we detect (via STP) that a switch port is in a non-forwarding
state, then the link is marked as being temporarily blocked and DHCP
discovery will be deferred until the link becomes unblocked.
The timer used to decide when to give up waiting for ProxyDHCPOFFERs
is currently based on the time that DHCP discovery was started, and
makes no allowances for any time spent waiting for the link to become
unblocked. Consequently, if STP is used then the timeout for
ProxyDHCPOFFERs becomes essentially zero.
Fix by resetting the recorded start time whenever DHCP discovery is
deferred due to a blocked link.
Debugged-by: Sebastian Roth <sebastian.roth@zoho.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The name "vesafb" is intrinsically specific to a BIOS environment.
Generalise the build configuration option CONSOLE_VESAFB to
CONSOLE_FRAMEBUFFER, in preparation for adding EFI framebuffer
support.
Existing configurations using CONSOLE_VESAFB will continue to work.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid accidentally dereferencing a NULL cipher context pointer for
plaintext blocks (which are usually messages with a block length of
zero, indicating a missing block).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI UNDI is a hideously ugly lump of poorly specified garbage bolted
on as an appendix of the UEFI specification. My personal favourite
line from the UNDI 'specification' is section E.2.2, which states
"Basically, the rule is: Do it right, or don't do it at all". The
author appears to believe that such exhortations are a viable
substitute for documenting what it is that the wretched reader is
supposed to, in fact, do.
(Second favourite is the section listing the pros and cons of various
driver types. This fails to identify a single con for the mythical
"Hardware UNDI", a design so insanely intrinsically slow that it
appears to have been the inspiration for the EFI_USB_IO_PROTOCOL.)
UNDI is functionally isomorphic to the substantially less preposterous
EFI_SIMPLE_NETWORK_PROTOCOL. Provide an UNDI interface (as a thin
wrapper around the existing SNP interface) to allow for use by
third-party software that has made poor life choices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Calling EDK2's OpenProtocol() with attributes BY_DRIVER|EXCLUSIVE will
call DisconnectController() in a loop to attempt to dislodge any
existing openers with attributes BY_DRIVER. The loop will continue
indefinitely until either no such openers remain, or until
DisconnectController() returns an error.
If our driver binding protocol's Stop() method is ever called to
disconnect a device that we are not in fact driving, then return
EFI_DEVICE_ERROR rather than EFI_SUCCESS, in order to break this
potentially infinite loop.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Microsoft PE/COFF specification defines the MajorLinkerVersion and
MinorLinkerVersion fields as "The linker major version number" and
"The linker minor version number" respectively, and has nothing more
to say on the matter. These fields have no significance: they do not
affect the interpretation of the remainder of the file, but merely
provide diagnostic information for interested humans to read.
Apparently, versions 2.4 and earlier of the Microsoft linker produced
binaries so incorrigibly cursed that even to attempt to parse such a
binary would risk summoning a plague of enraged spiders. To protect
users from unwanted arachnids, ImageHlp.dll's MapAndLoad() function
will helpfully fail to map and/or load a 32-bit binary unless the
linker version field indicates version 2.5 or later. (64-bit binaries
are exempt from such helpfulness.)
Work around the broken Microsoft ImageHlp.dll library by providing a
linker version number that will satisfy the arbitrary whims of the
MapAndLoad() function.
This mirrors wimboot commit 670c7e2 ("[efi] Work around broken 32-bit
PE executable parsing in ImageHlp.dll").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use INT 1a,564e to notify the BIOS of each network device that we
detect. This provides an opportunity for the BIOS to implement
platform policy such as changing the MAC address by issuing a call to
PXENV_UNDI_SET_STATION_ADDRESS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Invoke INT 1a,564e whenever a PXE stack is activated, passing the
address of the PXENV+ structure in %es:%bx. This is designed to allow
a BIOS to be notified when a PXE stack has been installed, providing
an opportunity for start-of-day commands such as setting the MAC
address according to a policy chosen by the BIOS.
PXE defines INT 1a,5650 as a means of locating the PXENV+ structure:
this call returns %ax=0x564e and the address of the PXENV+ structure
in %es:%bx. We choose INT 1a,564e as a fairly natural notification
call, using the parameters as would be returned by INT 1a,5650.
The full calling convention (documented as per section 3.1 of the PXE
specification) is:
INT 1a,564e - PXE installation notification
Enter:
%ax = 0x564e
%es = 16-bit segment address of the PXENV+ structure
%bx = 16-bit offset of the PXENV+ structure
Exit:
%edx may be trashed (as is the case for INT 1a,5650)
All other register contents must be preserved
CF is cleared
IF is preserved
All other flags are undefined
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid dragging in unnecessary iPXE header files such as <ipxe/uuid.h>
and <ipxe/tables.h> when building host utilities, and ensure that
FILE_LICENCE() (present in the imported EDK2 headers) expands to a
no-op.
Reported-by: Michael Tautschnig <mt@debian.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 7d36a1b ("[build] Explicitly link efilink against -liberty")
introduced a dependency on libiberty to cope with old versions of
libbfd. This commit dates from 2008 and seems to apply only to what
are now extremely old versions of libbfd (prior to binutils 2.12).
There are systems (such as current Debian) which do not include
libiberty within the binutils packages. On such systems, our build
dependency on libiberty represents a pointless hurdle.
Remove the explicit dependency on libiberty, hoping that there are no
modern systems where this will cause a problem.
Suggested-by: Ben Hildred <42656e@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the UEFI platform firmware to provide drivers for unrecognised
devices, by exposing our own implementation of EFI_USB_IO_PROTOCOL.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Make the class ID a property of the USB driver (rather than a property
of the USB device ID), and allow USB drivers to specify a wildcard ID
for any of the three component IDs (class, subclass, or protocol).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generate a score for each possible USB device configuration based on
the available driver support, and select the configuration with the
highest score. This will allow us to prefer ECM over RNDIS (for
devices which support both) and will allow us to meaningfully select a
configuration even when we have drivers available for all functions
(e.g. when exposing unused functions via EFI_USB_IO_PROTOCOL).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The decision on whether or not a zero-length packet needs to be
transmitted is independent of the host controller and belongs in the
USB core.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TCP/IP checksum fields are one's complement values and therefore have
two possible representations of zero: positive zero (0x0000) and
negative zero (0xffff).
In RFC768, UDP over IPv4 exploits this redundancy to repurpose the
positive representation of zero (0x0000) to mean "no checksum
calculated"; checksums are optional for UDP over IPv4.
In RFC2460, checksums are made mandatory for UDP over IPv4. The
wording of the RFC is such that the UDP header is mandated to use only
the negative representation of zero (0xffff), rather than simply
requiring the checksum to be correct but allowing for either
representation of zero to be used.
In RFC1071, an example algorithm is given for calculating the TCP/IP
checksum. This algorithm happens to produce only the positive
representation of zero (0x0000); this is an artifact of the way that
unsigned arithmetic is used to calculate a signed one's complement
sum (and its final negation).
A common misconception has developed (exemplified in RFC1624) that
this artifact is part of the specification. Many people have assumed
that the checksum field should never contain the negative
representation of zero (0xffff).
A sensible receiver will calculate the checksum over the whole packet
and verify that the result is zero (in whichever representation of
zero happens to be generated by the receiver's algorithm). Such a
receiver will not care which representation of zero happens to be used
in the checksum field.
However, there are receivers in existence which will verify the
received checksum the hard way: by calculating the checksum over the
remainder of the packet and comparing the result against the checksum
field. If the representation of zero used by the receiver's algorithm
does not match the representation of zero used by the transmitter (and
so placed in the checksum field), and if the receiver does not
explicitly allow for both representations to compare as equal, then
the receiver may reject packets with a valid checksum.
For UDP, the combined RFCs effectively mandate that we should generate
only the negative representation of zero in the checksum field.
For IP, TCP and ICMP, the RFCs do not mandate which representation of
zero should be used, but the misconceptions which have grown up around
RFC1071 and RFC1624 suggest that it would be least surprising to
generate only the positive representation of zero in the checksum
field.
Fix by ensuring that all of our checksum algorithms generate only the
positive representation of zero, and explicitly inverting this in the
case of transmitted UDP packets.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Tested-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow iPXE to coexist with other USB device drivers, by attaching to
the EFI_USB_IO_PROTOCOL instances provided by the UEFI platform
firmware.
The EFI_USB_IO_PROTOCOL is an unsurprisingly badly designed
abstraction of a USB device. The poor design choices intrinsic in the
UEFI specification prevent efficient operation as a network device,
with the result that devices operated using the EFI_USB_IO_PROTOCOL
operate approximately two orders of magnitude slower than devices
operated using our native EHCI or xHCI host controller drivers.
Since the performance is so abysmally slow, and since the underlying
problems are due to fundamental architectural mistakes in the UEFI
specification, support for the EFI_USB_IO_PROTOCOL host controller
driver is left as disabled by default. Users are advised to use the
native iPXE host controller drivers instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Many UEFI NBPs expect to find an EFI_PXE_BASE_CODE_PROTOCOL installed
in addition to the EFI_SIMPLE_NETWORK_PROTOCOL. Most NBPs use the
EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the cached DHCP packets.
This implementation has been tested with grub.efi, shim.efi,
syslinux.efi, and wdsmgfw.efi. Some methods (such as Discover() and
Arp()) are not used by any known NBP and so have not (yet) been
implemented.
Usage notes for the tested bootstraps are:
- grub.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet, and uses no other methods.
- shim.efi uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the cached
DHCP packet and to retrieve the next NBP via the Mtftp() method.
If shim.efi was downloaded via HTTP (or other non-TFTP protocol)
then shim.efi will blindly call Mtftp() with an HTTP URI as the
filename: this allows the next NBP (e.g. grubx64.efi) to also be
transparently retrieved by HTTP.
shim.efi can also use the EFI_SIMPLE_FILE_SYSTEM_PROTOCOL to
retrieve files previously loaded by "imgfetch" or similar commands
in iPXE. The current implementation of shim.efi will use the
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL only if it does not find an
EFI_PXE_BASE_CODE_PROTOCOL; this patch therefore prevents this
usage of our EFI_SIMPLE_FILE_SYSTEM_PROTOCOL. This logic could be
trivially reversed in shim.efi if needed.
- syslinux.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet. Versions 6.03 and earlier have a bug which
may cause syslinux.efi to attach to the wrong NIC if there are
multiple NICs in the system (or if the UEFI firmware supports
IPv6).
- wdsmgfw.efi (ab)uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the
cached DHCP packets, and to send and retrieve UDP packets via the
UdpWrite() and UdpRead() methods. (This was presumably done in
order to minimise the amount of benefit obtainable by switching to
UEFI, by replicating all of the design mistakes present in the
original PXE specification.)
The EFI_DOWNGRADE_UX configuration option remains available for now,
until this implementation has received more widespread testing.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge the functionality of parse_next_server_and_filename() and
tftp_uri() into a single pxe_uri(), which takes a server address
(IPv4/IPv6/none) and a filename, and produces a URI using the rule:
- if the filename is a hierarchical absolute URI (i.e. includes a
scheme such as "http://" or "tftp://") then use that URI and ignore
the server address,
- otherwise, if the server address is recognised (according to
sa_family) then construct a TFTP URI based on the server address,
port, and filename
- otherwise fail.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently do not populate the ciaddr field in the constructed PXE
Boot Server ACK packet. This causes a WDS server to respond with a
broadcast packet, which is then ignored by wdsmgfw.efi since it does
not match the specified IP address filter.
Fix by populating ciaddr within the constructed PXE Boot Server ACK
packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our SNP ReceiveFilters() method is a no-op, since we always (if
possible) use promiscuous mode for all network cards. The method
currently returns EFI_NOT_READY if the SNP interfaces are claimed for
use by iPXE, as with all other SNP methods.
The WDS bootstrap wdsmgfw.efi attempts to use both the PXE Base Code
protocol and the Simple Network Protocol simultaneously. This is
fundamentally broken, since use of the PXE Base Code protocol requires
us to disable the use of SNP (by claiming the interfaces for use by
iPXE), otherwise MnpDxe swallows all of the received packets before
our PXE Base Code's UdpRead() method is able to return them.
The root cause of this problem is that, as with BIOS PXE, the network
booting portions of the UEFI specification are less of a specification
and more of an application note sketchily describing how the original
hacked-together Intel implementation works. No sane design would ever
have included the UdpWrite() and UdpRead() methods.
Work around these fundamental conceptual flaws by unconditionally
returning success from efi_snp_receive_filters().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some distributions (observed with Ubuntu 15.04) place ldlinux.c32 in a
separate directory from isolinux.bin. Search for these files
separately, and allow an alternative location of ldlinux.c32 to be
provided via LDLINUX_C32=... on the make command line.
Reported-by: Adrian Koshka <adriankoshcha@teknik.io>
Tested-by: Adrian Koshka <adriankoshcha@teknik.io>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The debug directory size specified in the data directory should cover
only the EFI_IMAGE_DEBUG_DIRECTORY_ENTRY structure, not the whole of
the .debug section.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add definitions of protocols observed to be used by wdsmgfw.efi, and
add a handle name type for ConIn, ConOut, and StdErr.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit edf74df ("[pxe] Always reconstruct packet for
PXENV_GET_CACHED_INFO") fixed the problems caused by returning stale
DHCP packets (e.g. from an earlier boot attempt using a different
network device), but broke interoperability with NBPs such as WDS
which may overwrite our cached (fake) DHCP packets and expect the
modified packets to be returned by a subsequent call to
PXENV_GET_CACHED_INFO.
Fix by constructing the fake DHCP packets immediately before
transferring control to a PXE NBP. Calls to PXENV_GET_CACHED_INFO
will now never modify the cached packets.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add debug wrappers for more boot services functions, and print
symbolic values rather than raw numbers where possible.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The raw EFI_HANDLE value is almost never useful to know, and simply
adds noise to the already verbose debug messages. Improve the
legibility of debug messages by using only the name generated by
efi_handle_name().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We attempt to mimic the behaviour of Intel's PXE ROM by skipping the
separate ProxyDHCPREQUEST if the ProxyDHCPOFFER already contains a
boot filename or a PXE boot menu.
Experimentation reveals that Intel's PXE ROM will also check for a
non-empty next-server address alongside the boot filename. Update our
test to match this behaviour.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Tested-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 09b057c ("[settings] Remove "uristring" setting type") removed
support for URI-encoded settings via the "uristring" setting type, on
the basis that such encoding was no longer necessary to avoid problems
with the command line parser.
Other valid use cases for the "uristring" setting type do exist: for
example, a password containing a '/' character expanded via
chain http://username:${password:uristring}@server.name/boot.php
Restore the existence of the "uristring" setting, avoiding the
potentially large stack allocations that were used in the old code
prior to commit 09b057c ("[settings] Remove "uristring" setting
type").
Requested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When booting without an embedded script, display the imgstat()
information immediately before executing the downloaded image. This
allows potentially useful diagnostic information (such as the detected
image type) to be observed by the user without needing to enter the
iPXE shell and manually download the image.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current usage pattern of image_probe() is a legacy from the time
before commit 34b6ecb ("[image] Simplify image management") when
loading an image to its executable location in memory was a separate
action from actually executing the image.
Call image_probe() as soon as an image is registered. This allows
"imgstat" to display image type information for all images and allows
image-consuming code to assume that image->type is already set
correctly.
Ignore failures if image_probe() does not recognise the image, since
we do expect to handle unrecognised images (initrds, modules, etc).
Unrecognised images will be left with a NULL image->type, which
image-consuming code can easily check.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the return status from an embedded image to propagate out to the
eventual return status from main(). When running under Linux, this
allows the pass/fail result of unit tests to be observable without
having to visually inspect the console output.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A relatively common user mistake is to attempt to boot an EFI
executable (such as grub.efi) using a BIOS version of iPXE.
Unfortunately there are no signature checks that we can use to
unambiguously identify a PXE NBP, since a PXE NBP is just raw machine
code. We therefore have to accept anything sufficiently small to fit
into base memory as a valid PXE NBP.
We can detect that a file might be an EFI executable by checking for
the initial "MZ" signature bytes. This does not necessarily preclude
the file from also being a PXE NBP (since it would be possible to
create a hybrid binary which acts as both an EFI executable and a PXE
NBP, similar to the way in which wimboot and the Linux kernel are
hybrid binaries which act as both an EFI executable and a bzImage).
If the initial "MZ" signature bytes are present, then attempt to warn
the user by setting the image type to "PXE-NBP (may be EFI?)". We
can't (sensibly) prevent the user from accidentally running an EFI
executable as a PXE NBP, but we can at least make it easier for the
user to identify their mistake.
Inspired-by: Robin Smidsrød <robin@smidsrod.no>
Inspired-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some ProxyDHCP servers and PXE boot servers do not specify a DHCP
server identifier via option 54. We currently work around this in a
variety of ad-hoc ways:
- if a ProxyDHCPACK has no server identifier then we treat it as
having the correct server identifier,
- if a boot server ACK has no server identifier then we use the
packet's source IP address as the server identifier.
Introduce the concept of a DHCP server pseudo-identifier, defined as
being:
- the server identifier (option 54), or
- if there is no server identifier, then the next-server address
(siaddr),
- if there is no server identifier or next-server address, then the
DHCP packet's source IP address.
Use the pseudo-identifier in place of the server identifier when
handling ProxyDHCP and PXE boot server responses.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Infiniband link status change callback ipoib_link_state_changed()
may be called while the IPoIB device is closed, in which case there
will not be an IPoIB queue pair to be joined to the IPv4 broadcast
group. This leads to NULL pointer dereferences in ib_mcast_attach()
and ib_mcast_detach().
Fix by not attempting to join (or leave) the broadcast group unless we
actually have an IPoIB queue pair.
Signed-off-by: Wissam Shoukair <wissams@mellanox.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rewrite the HTTP core to allow for the addition of arbitrary content
encoding mechanisms, such as PeerDist and gzip.
The core now exposes http_open() which can be used to create requests
with an explicitly selected HTTP method, an optional requested content
range, and an optional request body. A simple wrapper provides the
preexisting behaviour of creating either a GET request or an
application/x-www-form-urlencoded POST request (if the URI includes
parameters).
The HTTP SAN interface is now implemented using the generic block
device translator. Individual blocks are requested using http_open()
to create a range request.
Server connections are now managed via a connection pool; this allows
for multiple requests to the same server (e.g. for SAN blocks) to be
completely unaware of each other. Repeated HTTPS connections to the
same server can reuse a pooled connection, avoiding the per-connection
overhead of establishing a TLS session (which can take several seconds
if using a client certificate).
Support for HTTP SAN booting and for the Basic and Digest
authentication schemes is now optional and can be controlled via the
SANBOOT_PROTO_HTTP, HTTP_AUTH_BASIC, and HTTP_AUTH_DIGEST build
configuration options in config/general.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI platforms may provide a watchdog timer, which will reboot the
machine if an operating system takes more than five minutes to load.
This can cause long-lived iPXE downloads (or interactive shell
sessions) to unexpectedly reboot.
Fix by resetting the watchdog timer every ten seconds while the iPXE
main processing loop continues to run.
Reported-by: Bradley B Williams <bradleybwilliams@swbell.net>
Reported-by: John Clark <john.r.clark.3@gmail.com>
Reported-by: wdriever@gmail.com
Reported-by: Charlie Beima <cbeima@indiana.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for SHA-224, SHA-384, and SHA-512 as digest algorithms in
X.509 certificates, and allow the choice of public-key, cipher, and
digest algorithms to be configured at build time via config/crypto.h.
Originally-implemented-by: Tufan Karadere <tufank@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current implementation handles big-endian 24-bit integers (which
occur in several TLS record types) by treating them as big-endian
32-bit integers which are shifted by 8 bits. This can result in
"Invalid read" errors when running under valgrind, if the 24-bit field
happens to be exactly at the end of an I/O buffer.
Fix by ensuring that we touch only the three bytes which comprise the
24-bit integer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Check for existence of the UART in uart_select(), not just in
uart_init(). This allows uart_select() to refuse to set a non-working
address in uart->base, which in turns means that the serial console
code will not attempt to use a non-existent UART.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When the ability for iPXE to handle multiple serial ports was added,
the choice was made that the singular serial port referred to by
COMBOOT calls should mean the port used for the serial console. This
unintentionally caused IMAGE_COMBOOT to also enable CONSOLE_SERIAL.
Fix by providing a weak-symbol version of the serial console which
will be used if serial console support was not explicitly enabled.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We do not set up any kind of virtual addressing before invoking an
ELFBoot image. Reject if the image's program headers indicate that
virtual addresses are not equal to physical addresses.
This avoids problems when loading some RHEL5 kernels, which seem to
include ELFBoot headers using virtual addressing. With this change,
these kernels are no longer detected as ELFBoot, and so may be
(correctly) detected as bzImage instead.
Reported-by: Torgeir.Wulfsberg@kongsberg.com
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow line buffer to accumulate multiple lines, with buffered_line()
returning each freshly-completed line as it is encountered. This
allows buffered lines to be subsequently processed as a group.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
VLAN and 802.11 devices use a network device operations structure that
wraps an underlying structure. For example, the vlan_operations
structure wraps the network device operations structure of the
underlying trunk device. This can cause false positives from the
current implementation of netdev_irq_supported(), which will always
report that VLAN devices support interrupts since it has no visibility
into the support provided by the underlying trunk device.
Fix by allowing network devices to explicitly flag that interrupts are
not supported, despite the presence of an irq() method.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iscsi_tx_done() is missing "break" statements at the end of each case.
(Fortunately, this happens not to cause a bug in practice, since
iscsi_login_request_done() is effectively a no-op when completing a
data-out PDU.)
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Extend the IPv6 concept of "scope ID" (indicating the network device
index) to IPv4 socket addresses, so that IPv4 multicast transmissions
may specify the transmitting network device.
The scope ID is not (currently) exposed via the string representation
of the socket address, since IPv4 does not use the IPv6 concept of
link-local addresses (which could legitimately be specified in a URI).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Redefine various IPv4 address constants and testing macros to avoid
unnecessary byte swapping at runtime, and slightly rename the macros
to prevent code from accidentally using the old definitions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid using zero as a network device index, so that a zero
sin6_scope_id can be used to mean "unspecified" (rather than
unintentionally meaning "net0").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When an IPv6 socket address string specifies a link-local or multicast
address but does not specify the requisite network device name
(e.g. "fe80::69ff:fe50:5845" rather than "fe80::69ff:fe50:5845%net0"),
assume the use of "netX".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove AXTLS headers now that no AXTLS code remains, with many thanks
to the AXTLS project for use of their cryptography code over the past
several years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the AES implementation from AXTLS with a dedicated iPXE
implementation which is slightly smaller and around 1000% faster.
This implementation has been verified using the existing self-tests
based on the NIST AES test vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generalise the existing support for performing CBC-mode block cipher
tests, and update the code to use okx() for neater reporting of test
results.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xfer_buffer() uses intf_get_dest_op() to obtain the destination
interface for xfer_deliver(), in order to check that this is the same
interface which provides xfer_buffer(). The return value from
intf_get_dest_op() (which contains the actual method implementing
xfer_deliver()) is not used.
On some gcc versions, this triggers a "value computed is not used"
warning, since the explicit type cast included within the
intf_get_dest_op() macro is treated as a "value computed".
Fix by explicitly casting the result of intf_get_dest_op() to void.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Reported-by: James A. Peltier <jpeltier@sfu.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Andrew Widdersheim
Torgeir Wulfsberg
Kyösti Mälkki
Carl Henrik Lunde
Fabrice Bacchella
Wissam Shoukair
Daniel Pieczko
Tufan Karadere