We currently use flat real mode wherever real mode is required. This
guarantees that we will not surprise some unsuspecting external caller
which has carefully set up flat real mode by suddenly reducing the
segment limits to 64kB.
However, operating in flat real mode imposes a severe performance
penalty in some virtualisation environments, since some CPUs cannot
fully virtualise flat real mode and so the hypervisor must fall back
to emulation. In particular, operating under KVM on a pre-Westmere
Intel CPU will be at least an order of magnitude slower, to the point
that there is a visible teletype effect when printing anything to the
BIOS console. (Older versions of KVM used to cheat and ignore the
"flat" part of flat real mode, which masked the problem.)
Switch (back) to using genuine real mode with 64kB segment limits
instead of flat real mode. Hopefully this won't break anything.
Add an explicit switch to flat real mode before returning to the BIOS
from the ROM prefix, since we know that a PMM BIOS will call the ROM
initialisation point (and potentially the BEV) in flat real mode.
As noted in previous commit messages, it is not possible to restore
the real-mode segment limits after a transition to protected mode,
since there is no way to know which protected-mode segment descriptor
was originally used to initialise the limit portion of the segment
register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Inside a virtual machine, writing the RX ring tail pointer may incur a
substantial overhead of processing inside the hypervisor. Minimise
this overhead by writing the tail pointer once per batch of
descriptors, rather than once per descriptor.
Profiling under qemu-kvm (version 1.6.2) shows that this reduces the
amount of time taken to refill the RX descriptor ring by around 90%.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Operations which are negligible on physical hardware (such as issuing
a posted write to the transmit ring tail register) may involve
substantial amounts of processing within the hypervisor if running in
a virtual machine.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As observed in commit 082cedb ("[build] Fix __libgcc attribute for
recent gcc versions"), recent versions of gcc have changed the
semantics of -mrtd as applied to the implicit arithmetic functions.
It is possible for tests to succeed even if our assumptions about
gcc's interpretation of -mrtd are incorrect. In particular, if gcc
chooses to utilise a frame pointer in the calling function, then it
can tolerate a temporarily incorrect stack pointer (since the stack
pointer will shortly afterwards be restored from the frame pointer
anyway).
Add tests designed specifically to check that our implementations of
the implicit arithmetic functions manipulate the stack pointer as
expected by gcc.
The effect of these tests can be observed by temporarily reverting
commit 082cedb ("[build] Fix __libgcc attribute for recent gcc
versions"): without this fix in place, the tests will fail on gcc 4.7
and later.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We observed some time ago (in commit 4ce8d61 "Import various libgcc
functions from syslinux") that gcc seems to treat calls to the
implicit arithmetic functions (e.g. __udivdi3()) as being affected by
-mregparm but unaffected by -mrtd.
This seems to be no longer the case with current gcc versions, which
treat calls to these functions as being affected by both -mregparm and
-mrtd, as expected.
There is nothing obvious in the gcc changelogs to indicate precisely
when this happened. From experimentation with available gcc versions,
the change occurred sometime between v4.6.3 and v4.7.2. We assume
that only versions up to v4.6.x require the special treatment.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a 32-bit system, 64-bit division is implemented using the libgcc
functions provided in __udivmoddi4.c etc. Calls to these functions
are generated automatically by gcc, with a calling convention that is
somewhat empirical in nature. Add these self-tests primarily as a
check that we are using the correct calling convention.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Escape sequences received via the serial console can fail since the
cpu_nap() in getchar_timeout() can delay processing for more than the
time it takes for a single character to arrive.
Fix by enabling the UART FIFOs.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It is unclear from the datasheets whether or not the TX ring can be
completely filled (i.e. whether writing the tail value as equal to the
current head value will cause the ring to be treated as completely
full or completely empty). It is very plausible that this edge case
could differ in behaviour between real hardware and the many
implementations of an emulated Intel NIC found in various virtual
machines. Err on the side of caution and always leave at least one
ring entry empty.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expand the concept of the X.509 cache to provide the functionality of
a certificate store. Certificates in the store will be automatically
used to complete certificate chains where applicable.
The certificate store may be prepopulated at build time using the
CERT=... build command line option. For example:
make bin/ipxe.usb CERT=mycert1.crt,mycert2.crt
Certificates within the certificate store are not implicitly trusted;
the trust list is specified using TRUST=... as before. For example:
make bin/ipxe.usb CERT=root.crt TRUST=root.crt
This can be used to embed the full trusted root certificate within the
iPXE binary, which is potentially useful in an HTTPS-only environment
in which there is no HTTP server from which to automatically download
cross-signed certificates or other certificate chain fragments.
This usage of CERT= extends the existing use of CERT= to specify the
client certificate. The client certificate is now identified
automatically by checking for a match against the private key. For
example:
make bin/ipxe.usb CERT=root.crt,client.crt TRUST=root.crt KEY=client.key
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Ensure that any generated files (such as DER forms of X.509
certificates) are rebuilt if the Makefile changes.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The build process currently attempts to disable ccache for files using
the .incbin directive, but the rule fails to apply to anything beyond
the simple object target. Fix by applying to all relevant build
targets (including debug objects, assembly listings, and so on).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently allocates a copy the certificate's common name as a
string. This string is used by the TLS and CMS code to check
certificate names against an expected name, and also appears in
debugging messages.
Provide a function x509_check_name() to centralise certificate name
checking (in preparation for adding subjectAlternativeName support),
and a function x509_name() to provide a name to be used in debugging
messages, and remove the dynamically allocated string.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Certificate authorities are not required to send the certificate used
to sign the OCSP response if the response is signed by the original
issuer.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At least one HTTP server (Google's OCSP responder) has been observed
to generate a Content-Length header with trailing whitespace.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some BIOSes (observed with a ProLiant DL360p Gen8 SE) perform no range
checking whatsoever on the parameters passed to INT10,06 and will
therefore happily write to an area beyond the end of video RAM. The
area immediately following the video RAM tends to be the VGA BIOS ROM
image. Overwriting the VGA BIOS leads to an interesting variety of
crashes and reboots.
Fix by specifying an exact width and height to be cleared, rather than
passing in large values and relying upon the BIOS to truncate them to
the appropriate range.
Reported-by: Alex Davies <adavies@jumptrading.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On an Asus Z87-K motherboard with an onboard 8168 NIC, booting into
Windows 7 and then warm rebooting into iPXE results in a broken RX
datapath: packets can be transmitted successfully but garbage is
received. A cold reboot clears the problem.
A dump of the PHY registers reveals only one difference: in the
failure case the bits ADVERTISE_PAUSE_CAP and ADVERTISE_PAUSE_ASYM are
cleared. Explicitly setting these bits does not fix the problem.
A dump of the MAC registers reveals a few differences, of which the
most obvious culprit is the undocumented bit 24 of the Receive
Configuration Register (RCR), which is set in the failure case.
Explicitly clearing this bit does fix the problem.
Reported-by: Sebastian Nielsen <ipxe@sebbe.eu>
Reported-by: Oliver Rath <rath@mglug.de>
Debugged-by: Sebastian Nielsen <ipxe@sebbe.eu>
Tested-by: Sebastian Nielsen <ipxe@sebbe.eu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some UEFI builds will set up a timer to continuously poll any SNP
devices. This can drain packets from the network device's receive
queue before iPXE gets a chance to process them.
Use netdev_rx_[un]freeze() to explicitly indicate when we expect our
network devices to be driven via the external SNP API (as we do with
the UNDI API on the standard BIOS build), and disable the SNP API
except when receive queue processing is frozen.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFIRC() uses PLATFORM_TO_ERRNO(), which evaluates its argument twice
(and can't trivially use a braced-group expression or an inline
function to avoid this, since it gets used outside of function
context).
The expression "EFIRC(main())" will therefore end up calling main()
twice, which is not the intended behaviour. Every other instance of
EFIRC() is of the simple form "EFIRC(rc)", so fix by converting this
instance to match.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for extraneous packets to be received during loopback testing,
and so permit loopback tests to be performed when ports are connected
to a switch (rather than requiring ports to be directly connected with
a loopback cable).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Inhibit implicit sign-padding of characters with the top bit set
(e.g. accented characters), which confuses the mucurses library by
colliding with the bits used to store character attributes and
colours.
Reported-by: Marc Delisle <Marc.Delisle@cegepsherbrooke.qc.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a 64-bit build, EFI_STATUS codes are 64-bit quantities, with the
"error/warning" bit located in bit 63.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE will detect timeout failures in several situations: network
link-up, DHCP, TCP connection attempts, unacknowledged TCP data, etc.
This does not cover all possible circumstances. For example, if a
connection to a web server is successfully established and the web
server acknowledges the HTTP request but never sends any data in
response, then no timeout will be triggered. There is no timeout
defined within the HTTP specifications, and the underlying TCP
connection will not generate a timeout since it has no way to know
that the HTTP layer is expecting to receive data from the server.
Add a "--timeout" parameter to "imgfetch", "chain", etc. If no
progress is made (i.e. no data is downloaded) within the timeout
period, then the download will be aborted.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Redefine the timeout parameter from "time since start of job" to "time
since progress was last made". This does not affect any existing
behaviour, since all existing users of the timeout parameter do not
provide progress indication.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A web server may return a 503 Service Unavailable response along with
a Retry-After header to direct the client to retry the request at a
later time.
The Retry-After header may be a number of seconds, or a full HTTP
timestamp (e.g. "Fri, 7 Mar 2014 17:22:14 GMT"). We have no
reasonable way of parsing a full HTTP timestamp; if the server chooses
to use this format then we simply retry after a fixed 5-second delay.
As per RFC 2616, in the absence of a Retry-After header we treat a
status code of 503 Service Unavailable as being equivalent to 500
Internal Server Error, and immediately fail the request.
Requested-by: Suresh Sundriyal <ssundriy@vmware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE uses currticks() (along with the MAC address(es) of any network
devices) to seed the (non-cryptographic) random number generator. The
current implementation of linux_currticks() ensures that the first
call to currticks() will always return zero; this results in identical
random number sequences on each run of iPXE on a given machine. This
can cause odd-looking behaviour due to e.g. the reuse of local TCP
port numbers.
Fix by effectively rounding down the start time recorded by
linux_currticks() to the nearest whole second; this makes it unlikely
that consecutive runs of iPXE will use the exact same RNG sequence.
(Note that none of this affects the cryptographic RNG, which uses
/dev/random as a source of entropy.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently ignores ACKs which do not acknowledge any new data.
(In particular, it does not stop the retransmission timer; this is
done to prevent an immediate retransmission if a duplicate ACK is
received while the transmit queue is non-empty.)
If a peer provides a window size of zero and later sends a duplicate
ACK to update the window size, this update will therefore be ignored
and iPXE will never be able to transmit data.
Fix by updating the window size even for ACKs which do not acknowledge
new data.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When opening a VLAN device, vlan_open() will call netdev_open() on the
trunk device. This will result in a call to netdev_notify(), which
will cause vlan_notify() to call vlan_sync() on the original VLAN
device, which will see that the trunk device is now open but the VLAN
device apparently isn't (since it has not yet been flagged as open by
netdev_open()). The upshot is a second attempt to open the VLAN
device, which will result in an erroneous second call to vlan_open().
This convoluted chain of events then terminates harmlessly since
vlan_open() calls netdev_open() on the trunk device, which just
returns immediately since the trunk device is by now flagged as being
already open.
Prevent this from happening by having netdev_open() flag the device as
open prior to calling the device's open() method, and reflagging it as
closed if the open() method fails.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit c429bf0 ("[romprefix] Store boot bus:dev.fn address as autoboot
device location") introduced a regression by using register %cx to
temporarily hold the PCI bus:dev.fn address, despite the fact that %cx
was already being used to hold the stored BIOS stack segment.
Consequently, when returning to the BIOS after a failed or cancelled
boot attempt, iPXE would end up calling INT 18 with the stack segment
set equal to the PCI bus:dev.fn address. Writing to essentially
random areas of memory tends to upset even the more robust BIOSes.
Fix by using register %ax to temporarily hold the PCI bus:dev.fn
address.
Reported-by: Anton D. Kachalov <mouse@yandex-team.ru>
Tested-by: Anton D. Kachalov <mouse@yandex-team.ru>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently pads initrd images to a multiple of 4kB and inserts
zero padding between images, as required by some versions of the Linux
kernel. The overall length reported via the ramdisk_size field in the
bzImage header includes this zero padding.
This causes problems when using memdisk to load a gzip-compressed disk
image. memdisk treats the ramdisk_size field as containing the exact
length of the initrd image, and uses this length to locate the 8-byte
gzip footer. This will generally cause memdisk to fail to decompress
the disk image.
Fix by reporting the exact length of the initrd image set, including
any padding inserted between images but excluding any padding added at
the end of the final image.
Reported-by: Levente LEVAI <levail@aviatronic.hu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently advertises a fixed MSS of 1460, which is correct only
for IPv4 over Ethernet. For IPv6 over Ethernet, the value should be
1440 (allowing for the larger IPv6 header). For non-Ethernet link
layers, the value should reflect the MTU of the underlying network
device.
Use tcpip_mtu() to calculate the transport-layer MTU associated with
the peer address, and calculate the MSS to allow for an optionless TCP
header as per RFC 6691.
As a side benefit, we can now fail a connection immediately with a
meaningful error message if we have no route to the destination
address.
Reported-by: Anton D. Kachalov <mouse@yandex-team.ru>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide the function tcpip_mtu() to allow external code to determine
the (transport-layer) maximum transmission unit for a given socket
address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide the function tcpip_netdev() to allow external code to
determine the transmitting network device for a given socket address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
qemu can load an option ROM which is not associated with a particular
PCI device using the "-option-rom" syntax. Under these circumstances,
we should ignore the PCI bus:dev.fn address that we expect to find in
%ax on entry to the initialisation vector.
Fix by using the PCI bus:dev.fn address only if it is non-zero. Since
00:00.0 will always be the host bridge, it can never be the address of
a network card.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Per the BIOS Boot Specification, the initialization phase of the ROM
is called with the PFA (PCI Function Address) in the %ax register.
The intention is that the ROM code will store that device address
somewhere and use it for booting from that device when the Boot Entry
Vector (BEV) is called. iPXE does store the PFA, but doesn't use it
to select the boot network device. This renders BIOS IPL lists fairly
ineffective.
Fix by using the BBS-specified bus:dev.fn address as the autoboot
device location.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE will currently attempt to boot from every network device for
which it has a driver. Where a system has more than one network
device supported by iPXE, this renders BIOS IPL lists ineffective.
Allow an autoboot device location to be specified. If such a location
is specified, then only devices matching that location will be used as
part of the automatic boot sequence. If no such location is
specified, then all devices will be used.
Note that this does not affect the "autoboot" command, which will
continue to use all devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently prints a "Press Ctrl-B" banner twice: once when the ROM
is first called for initialisation and again if we attempt to boot
from the ROM. This slows boot, especially when the NIC is not the
primary boot device. Tools such as libguestfs make use of QEMU VMs
for performing maintenance on disk images and may make use of NICs in
the VM for network support. If iPXE introduces a static init-time
delay, that directly translates to increased runtime for the tools.
Fix by allowing the ROM banner timeout to be configured independently
of the main banner timeout.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for parsing of URIs containing literal IPv6 addresses
(e.g. "http://[fe80::69ff:fe50:5845%25net0]/boot.ipxe").
Duplicate URIs by directly copying the relevant fields, rather than by
formatting and reparsing a URI string. This relaxes the requirements
on the URI formatting code and allows it to focus on generating
human-readable URIs (e.g. by not escaping ':' characters within
literal IPv6 addresses). As a side-effect, this allows relative URIs
containing parameter lists (e.g. "../boot.php##params") to function
as expected.
Add validity check for FTP paths to ensure that only printable
characters are accepted (since FTP is a human-readable line-based
protocol with no support for character escaping).
Construct TFTP next-server+filename URIs directly, rather than parsing
a constructed "tftp://..." string,
Add self-tests for URI functions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit b5f5f73 ("[cmdline] Expand settings within each command-line
token individually") effectively rendered the "uristring" setting type
obsolete, since strings containing whitespace no longer break the
command line parser. The concept of the "uristring" type is not well
defined, since URI escaping rules depend on which portion of a URI is
being escaped.
Remove the "uristring" type, converting it into an alias for the
"string" setting type so as to avoid breaking existing scripts.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When resizing DHCP options, iPXE currently calculates the length to be
copied by subtracting the destination pointer from the end of buffer
pointer. This works and guarantees not to write beyond the end of the
buffer, but may end up reading beyond the end of the buffer.
Fix by calculating the required length exactly.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit d4c0226 ("[dns] Support DNS search lists") introduced a
regression when handling CNAME records resolving to names longer than
the original name. The "end of name" offset stored in dns->offset was
not updated to reflect the length of the new name, causing
dns_question() to append the (empty) search suffix at an incorrect
offset within the name buffer, resulting in a mangled DNS name.
In the case of a CNAME record resolving to a name shorter than or
equal in length to the original name, then the mangling would occur in
an unused portion of the name buffer. In the common case of a name
server returning the A (or AAAA) record along with the CNAME record,
this would cause name resolution to succeed despite the mangling. (If
the name server did not return the A or AAAA record along with the
CNAME record, then the mangling would be revealed by the subsequent
invalid query packet.)
Reported-by: Nicolas Sylvain <nsylvain@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Update the DNS resolver to support DNS search lists (as provided by
DHCP option 119, DHCPv6 option 24, or NDP option 31).
Add validation code to ensure that parsing of DNS packets does not
overrun the input, get stuck in infinite loops, or (worse) write
beyond the end of allocated buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rename the "--bpp" option to "--depth", to free up the single-letter
option "-b" for "--bottom" in preparation for adding margin support.
This does not break backwards compatibility with documented features,
since the "console" command has not yet been documented.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for an arbitrary margin to be specified in the console
configuration. If the actual screen size does not match the requested
screen size, then update any margins specified so that they remain in
the same place relative to the requested screen size. If margins are
unspecified (i.e. zero), then leave them as zero.
The underlying assumption here is that any specified margins are
likely to describe an area within a background picture, and so should
remain in the same place relative to that background picture.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Centre the background picture on the console, to give a more
consistent result when the aspect ratio does not match the requested
width and height.
Once drawn for the first time, nothing should ever overwrite the
margins of the display. We can therefore eliminate the logic used to
redraw only the margin areas, and use much simpler code to draw the
complete initial background image.
Simplify the redrawing logic further by making the background picture
buffer equal in size to the frame buffer. In the common case of a
background picture which is designed to fill the screen, this wastes
no extra memory, and the combined code simplifications reduce the size
of fbcon.o by approximately 15%.
Redefine the concept of "margin" to match the intuitive definition
(i.e. the size of the gap, rather than the position of the boundary
line).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Fix incorrect calculation used to determine length of data to be
copied within a literal data block, and add a test case to prevent
this bug from going undetected in future.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow test reports to specify an explicit file name and line number
using the extended okx() macro. This allows large blocks of test
report code such as tcpip_random_ok() to be implemented as functions
rather than macros.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the magic colour facility to cause the user interface background
to become transparent when we have a background picture.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The magic basic colour can be remapped at runtime from COLOR_NORMAL_BG
(usually blue) to COLOR_DEFAULT (which will be transparent as a
background colour on the framebuffer console).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a centralised concept of colours and colour pairs (using the
default colour pairs as configured via config/colour.h). A colour
pair consists of a pair of colour indices.
Add the ability to redefine both a colour pair and an individual
colour index, with minimal overhead if this feature is not required
(e.g. because the relevant shell commands are not present in the
build).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a mechanism for consoles to update the recorded console width
and height, and use this width and height to provide the curses COLS
and LINES variables.
We choose not to use ANSI escape sequences to obtain the width and
height, for two reasons:
- iPXE's model is that all output is sent to all consoles; we could
therefore end up with multiple consoles reporting conflicting widths
and heights
- when a serial console is in use, we probably don't want to resize
the output shown on the BIOS console to match the size of the serial
console, since it's likely that the serial console is in use only
for debugging.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The vgabios used by bochs and qemu (and other virtualisation products)
has a bug in its implementation of INT 10,4f00 which causes the high
16 bits of %ebx and %edx to become corrupted.
The vgabios code uses a "pushaw"/"popaw" pair to preserve the low 16
bits of all non-segment registers. The vgabios code is compiled using
bcc, which generates 8086-compatible code and so never touches the
high 16 bits of the 32-bit registers. However, the function
vbe_biosfn_return_controller_information() includes the line:
size_64k = (Bit16u)((Bit32u)cur_info->info.XResolution *
cur_info->info.XResolution *
cur_info->info.BitsPerPixel) >> 19;
which generates an implicit call to the "lmulul" function. This
function is implemented in vbe.c as:
; helper function for memory size calculation
lmulul:
and eax, #0x0000FFFF
shl ebx, #16
or eax, ebx
SEG SS
mul eax, dword ptr [di]
mov ebx, eax
shr ebx, #16
ret
which modifies %eax, %ebx, and %edx (as a result of the "mul"
instruction, which places its result into %edx:%eax).
Work around this problem by marking %ebx and %edx as being clobbered
by the call to INT 10,4f00. (%eax is already used as an output
register, so does not need to be on the clobber list.)
Reported-by: Oliver Rath <rath@mglug.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for equivalent IPv4 and IPv6 settings (which requires equivalent
settings to be adjacent within the settings list).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for multiple setting definitions with the same name but
different scopes and tags. For example, allow for a "filename"
setting with default scope and tag value 67 (for DHCPv4) and a
corresponding "filename" setting with IPv6 scope and tag value 59 (for
DHCPv6).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Note that IANA has not yet assigned a DHCPv6 option code for the
syslog server. When a code is assigned, the definition of
DHCPV6_LOG_SERVERS should be updated. Until then, an IPv6 address of
a syslog server can be configured manually using e.g.
set syslog6 3ffe:302:11:2::8309
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our policy is to prefer IPv6 addreses to IPv4 addresses, but to
request IPv6 addresses only if we have an IPv6 address for the name
server itself.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for the existence of references to IPv6 setting types without
dragging in the whole IPv6 stack, by placing the definition of
setting_type_ipv6 in core/settings.c and providing weak stub methods
for parse_ipv6_setting() and format_ipv6_setting().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The fetch_setting() family of functions may currently modify the
definition of the specified setting (e.g. to add missing type
information). Clean up this interface by requiring callers to provide
an explicit buffer to contain the completed definition of the fetched
setting, if required.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ANSI escape sequences to show and hide the cursor take the form
"<ESC>[?25h" and "<ESC>[?25l" respectively. iPXE currently treats the
'?' character as the final byte. Fix by explicitly treating '?' as an
intermediate byte.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
OpenBSD 5.4 seems to generate dynamically linked binaries by default,
which breaks our build process. Fix by forcing the linker to always
create static binaries.
Reported-by: Jiri B <jirib@devio.us>
Tested-by: Jiri B <jirib@devio.us>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no requirement for VBE modes to be listed in increasing order
of resolution. With the present logic, this can cause e.g. a 1024x768
mode to be selected if the user asks for 640x480, if the 1024x768 mode
is earlier in the mode list.
Define a scoring system for modes as
score = ( width * height - bpp )
and choose the mode with the lowest score among all acceptable modes.
This should prefer to choose the mode closest to the requested
resolution, with a slight preference for higher colour depths.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The VirtualBox BIOS fails to retrieve mode information (with status
0x0100) for some modes within the mode list. Skip any such modes,
rather than treating this as a fatal error.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The VESA frame buffer console uses the VESA BIOS extensions (VBE) to
enumerate video modes, selects an appropriate mode, and then hands off
to the generic frame buffer code.
The font is extracted from the VGA BIOS, avoiding the need to provide
an external font file.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the "initialising devices" message to show up on consoles which
require initialisation, by deferring it until after initialise() has
completed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for IPv6 routing table entries to be created for an on-link
prefix where a local address has not yet been assigned to the network
device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Syslinux 6.x places its files into a bios subdirectory, and requires
that a ldlinux.c32 module be included within the ISO image. Add the
relevant search paths for isolinux.bin, and include the file
ldlinux.c32 within the ISO image if it exists.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for the stateful and stateless variants of the DHCPv6
protocol. The resulting settings block is registered as
"net<x>.dhcpv6", and DHCPv6 options can be obtained using
e.g. "${net0.dhcpv6/23:ipv6}" to obtain the IPv6 DNS server address.
IPv6 addresses obtained via stateful DHCPv6 are not yet applied to the
network device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The retrieval of the cached DHCPACK and the creation of network
devices are both currently scheduled as STARTUP_NORMAL. It is
therefore possible that the cached DHCPACK will not be retrieved in
time for cachedhcp_probe() to apply it to the relevant network device.
Fix by retrieving the cached DHCPACK at initialisation time rather
than at startup time.
As an optimisation, an unclaimed cached DHCPACK can be freed
immediately after the last network device has been created, rather
than waiting until shutdown.
Reported-by: Espen Braastad <espen.braastad@redpill-linpro.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include IPv6 within the generic network device configurator
mechanism. The IPv6 configurator will send a router solicitation and
wait for a router advertisement to be received. (As per RFC4861
section 6.3.7, we do this even if advertisements have been received
prior to sending the router solicitation.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE supports multiple mechanisms for network device configuration:
DHCPv4 for IPv4, FIP for FCoE, and SLAAC for IPv6. At present, DHCPv4
requires an explicit action (e.g. a "dhcp" command), FIP is initiated
implicitly upon opening a network device, and SLAAC takes place
whenever a RA happens to be received.
Add a generic concept of a network device configurator, which provides
a common interface to triggering configuration and to reporting the
result of the configuration process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5e1fa5c ("[parseopt] Add parse_timeout()") introduced a
regression causing the shell banner timeout value (calculated in
milliseconds) to be treated as a timer tick count, resulting in a
timeout of approximately two minutes rather than the intended two
seconds.
Reported-by: Christian Hesse <list@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a job times out then use the most recent ongoing error status
reported via job_progress() (if available) as the overall return
status.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some background jobs have a meaningful ongoing status code (e.g. the
current link status for a job waiting for a network link to come up).
Allow this to be exposed via the job_progress() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If an object interface does not provide an intf_close() method, then
default to calling intf_restart(). This allows static objects to
safely ignore intf_close(), without needing to add code solely to
ensure that the interface gets unplugged.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most network upper-layer drivers do not implement all three methods
(probe, notify, and remove). Save code by making all methods
optional.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Parsing a timeout value (specified in milliseconds) into an internal
timeout value measured in timer ticks is a common operation. Provide
a parse_timeout() value to carry out this conversion automatically.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading, always retrieve the cached DHCPACK packet from the
underlying PXE stack, and apply it as the original contents of the
"net<X>.dhcp" settings block. This allows cached DHCP settings to be
used for any chainloaded iPXE binary (not just undionly.kkpxe).
This change eliminates the undocumented "use-cached" setting. Issuing
the "dhcp" command will now always result in a fresh DHCP request.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When transmitting to a link-local or multicast destination address,
use the network device's link-local address as the source address if
no explicit source address has been specified.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The IPv6 option length field represents the length of the option data
field, not the overall length of the option.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add generic pinger mechanism (analogous to the generic downloader
mechanism) which opens a ping socket, transmits ping requests, and
passes information about ping replies to a callback function.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge common functionality between IPv4 and IPv6 ICMP echo handling,
and add support for transmitting ICMP echo requests and delivering
ICMP echo replies to a (not yet implemented) ping_rx() function.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 238050d ("[build] Work around bug in gcc >= 4.8") works around
one instance of a bug in recent versions of gcc, in which "ebp" cannot
be specified within an asm clobber list.
Some versions of gcc seem to exhibit the same bug on other points in
the codebase. Fix by changing all instances of "ebp" in a clobber
list to use the push/pop %ebp workaround instead.
Originally-implemented-by: Víctor Román Archidona <contacto@victor-roman.es>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The path MTU is currently hardcoded to 1460 bytes, which fails to
allow space for TCP options. Sending a maximum-sized datagram (which
is viable when using HTTP POST) will therefore fail since the Ethernet
MTU will be exceeded.
Reduce the hardcoded path MTU to produce a maximum datagram of 1280
bytes, which is the size required of data link layers by IPv6. It is
a reasonable assumption that all intermediary data link layers will be
able to convey this packet without fragmentation, even for IPv4.
Note that this reduction has a minimal impact upon download
throughput, since it affects only the transmit data path.
Originally-fixed-by: Suresh Sundriyal <ssundriy@vmware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the existing partially-implemented IPv6 stack with a fresh
implementation.
This implementation is not yet complete. The IPv6 transmit and
receive datapaths are functional (including fragment reassembly and
parsing of arbitrary extension headers). NDP neighbour solicitations
and advertisements are supported. ICMPv6 echo is supported.
At present, only link-local addresses may be used, and there is no way
to specify an IPv6 address as part of a URI (either directly or via
a DNS lookup).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Split the protocol-independent portions of arp.c into a separate file
neighbour.c, to allow for sharing of functionality between IPv4+ARP
and IPv6+NDP.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
IPv6 link-local socket addresses require some way to specify a local
network device. We cannot simply use a pointer to the network device,
since a struct sockaddr_in6 may be long-lived and has no way to hold a
reference to the network device.
Using a network device index allows a socket address to cleanly refer
to a network device without worrying about whether or not that device
continues to exist.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give tap devices a meaningful name, and avoid segmentation faults when
attempting to retrieve ${net0/bustype} by assigning a new bus type for
tap devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for configurable provision of built-in settings by placing them
in a linker table rather than an array.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Prevent the card from flagging packets of 1518 bytes length as
overlength.
This fixes the High-MTU loopback test.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The 3c90x B and C revisions support rounding up the packet length to a
specific boundary. Disable this feature to avoid overlength packets.
This fixes the loopback test.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to the 3c90x datasheet we have to stall the upload (receive)
engine before setting the receive ring address.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow HTTP POST requests to be generated when the URI includes a
parameter list. For example:
#!ipxe
params
param mac ${net0/mac}
param uuid ${uuid}
param asset ${asset}
chain http://boot.ipxe.org/demo/boot.php##params
Signed-off-by: Michael Brown <mcb30@ipxe.org>
HTTP POST requires the ability to associate a parameter list with a
URI. There is no standardised syntax for this. Use a non-standard
URI syntax to incorporate the specification of a parameter list within
a URI:
URI = [ absoluteURI | relativeURI ]
[ "#" fragment ] [ "##params" [ "=" paramsName ] ]
e.g.
http://boot.ipxe.org/demo/boot.php##paramshttp://boot.ipxe.org/demo/boot.php##params=mylist
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow memory map entries to be read using the syntax
${memmap/<region>.<properties>.<scale>}
where <region> is the index of the memory region, <properties> is a
bitmask where bit 0 represents the start address and bit 1 represents
the length (allowing the end address to be encoded by having both bits
0 and 1 set), and <scale> is the number of bits by which to shift the
result.
This allows for several values of interest to be encoded. For
example:
${memmap/<region>.1.0:hexraw} # 64-bit start address of <region>
${memmap/<region>.2.0:hexraw} # 64-bit length of <region>, in bytes
${memmap/<region>.3.0:hexraw} # 64-bit end address of <region>
${memmap/<region>.2.10:int32} # Length of <region>, in kB
${memmap/<region>.2.20:int32} # Length of <region>, in MB
The numeric encoding is slightly more sophisticated than described
here, allowing a single encoding to cover multiple regions. (See the
source code for details.) The primary use case for this feature is to
provide the total system memory size (in MB) via the "memsize"
predefined setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow numeric_setting_value() to handle e.g. the byte sequence
00:00:00:00:12:34:56:78
by returning -ERANGE only if the value actually overflows the return
type.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow CPUID values to be read using the syntax
${cpuid/<register>.<function>}
For example, ${cpuid/2.0x80000001} will give the value of %ecx after
calling CPUID with %eax=0x80000001. Values for <register> are encoded
as %eax=0, %ebx=1, %ecx=2, %edx=3.
The numeric encoding is more sophisticated than described above,
allowing for settings such as the CPU model (obtained by calling CPUID
with %eax=0x80000002-0x80000004 inclusive and concatenating the values
returned in %eax:%ebx:%ecx:%edx). See the source code for details.
The "cpuvendor" and "cpumodel" settings provide easy access to these
more complex CPUID settings.
This functionality is intended to complement the "cpuid" command,
which allows for testing individual CPUID feature bits.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This makes it possible to leave UDP debugging enabled in order to see
interesting UDP events, without flooding the console with at least one
message per packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "inc" command allows the numeric value of a setting to be
incremented, allowing for the construction of simple loops within an
iPXE script.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow commands to be placed on the same line as a label. This allows
for improved legibility of loop constructions by incorporating the
loop check condition into the same line as the loop label. For
example, to iterate over network devices using the forthcoming "inc"
command:
set idx:int16 0
:loop isset ${net${idx}/mac} || goto loop_done
echo net${idx} is a ${net${idx}/chip} with MAC ${net${idx}/mac}
inc idx && goto loop
:loop_done
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Initial whitespace is already accepted on lines containing commands,
since it gets ignored by the system() call. Minimise surprise and
allow for neater indentation of scripts by also allowing whitespace on
lines containing labels.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A deliberate side effect of this commit is that the "read" command
will now preserve the type of the setting, if the setting name
contains no type information. For example:
iPXE> set foo:ipv4 192.168.0.1
iPXE> read foo
192.168.0.100
iPXE> show foo
foo:ipv4 = 192.168.0.100
rather than the arguably unexpected behaviour of resetting the type to
"string".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use parse_setting_name() and fetchf_setting_copy() in
expand_settings(), to eliminate the call to fetchf_named_setting().
This change also eliminates the potentially large stack-allocated
buffer in expand_settings().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
fetch_settings_copy() currently returns success and a NULL data
pointer to indicate a non-existent setting. This is intended to allow
the caller to differentiate between a non-existent setting and an
error in allocating memory for the copy of the setting.
The underlying settings blocks' fetch() methods provide no way to
perform an existence check separate from an attempt to fetch the
setting. A "non-existent setting" therefore means simply a setting
for which an error was encountered when attempting to fetch from every
settings block within the subtree.
Since any underlying error within a settings block (e.g. a GuestRPC
failure when attempting to retrieve a VMware GuestInfo setting) will
produce the effect of a "non-existent setting", it seems somewhat
meaningless to give special treatment to memory allocation errors
within fetch_setting_copy().
Remove the special treatment and simplify the semantics of
fetch_setting_copy() by directly passing through any underlying error
(including non-existence) encountered while fetching the setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There are currently two conflicting usages of the term "named setting"
within iPXE: one refers to predefined settings (such as show up in the
"config" UI), the other refers to settings identified by a name (such
as "net0.dhcp/ip").
Split these usages into the term "predefined setting" and "named
setting" to avoid ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our use of --gc-sections causes the linker to discard the symbols
defined by FILE_LICENCE(), meaning that the resulting licence
determination is incomplete.
We must use the KEEP() directive in the linker script to force the
linker to not discard the licence symbols. Using KEEP(*(COMMON))
would be undesirable, since there are some symbols in COMMON which we
may wish to discard.
Fix by placing symbols defined by PROVIDE_SYMBOL() (which is used by
FILE_LICENCE()) into a special ".provided" section, which we then mark
with KEEP(). All such symbols are zero-length, so there is no cost in
terms of the final binary size.
Since the symbols are no longer in COMMON, the linker will reject
symbols with the same name coming from multiple objects. We therefore
append the object name to the licence symbol, to ensure that it is
unique.
Reported-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The getopt API defines optind as a global variable. When used by the
"autoboot" command, the payload function passed to ifcommon_exec() may
result in a new iPXE script being executed; the commands therein would
then overwrite the value of optind. On returning, ifcommon_exec()
would continue processing the list of interfaces from an undefined
point.
Fix by using a local variable to hold the index within the list of
interfaces.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some hardware (observed with an onboard RTL8168) will erroneously
report a buffer overflow error if the received packet exactly fills
the receive buffer.
Fix by adding an extra four bytes of padding to each receive buffer.
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for page up, page down, home and end keys, matching the
navigation logic used in the menu user interface.
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Adrian Jamróz <adrian.jamroz@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow long script lines to be broken up using backslash continuation.
For example:
choose --default linux --timeout 3000 os \
&& goto boot_${os} || goto cancelled
Requested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
base16_encode() will fail to generate a terminating NUL if the length
of the raw data is zero, since the loop calling sprintf() will never
execute.
Fix by explicitly terminating the result with a NUL.
Reported-by: Marin Hannache <git@mareo.fr>
Debugged-by: Marin Hannache <git@mareo.fr>
Tested-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old via-rhine driver with a new version using the iPXE
API.
Includes fixes by Thomas Miletich for:
- MMIO access
- Link detection
- RX completion in RX overflow case
- Reset and EEPROM reloading
- CRC stripping
- Missing cpu_to_le32() calls
- Missing memory barriers
Signed-off-by: Adrian Jamróz <adrian.jamroz@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Modified-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include a sequence number as the first four bytes of the loopback test
packet payload. When a content mismatch occurs, this gives some
information about the source of the mismatched packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow any iPXE command expecting a network device name to accept
"netX" as a synonym for "most recently opened network device".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a facility for settings blocks to act as symbolic links to other
settings blocks, and reimplement the "netX" virtual settings block
using this facility.
The primary advantage of this approach is that unscoped settings such
as ${mac} and ${filename} will now reflect the settings obtained from
the most recently opened network device: in most cases, this will mean
the settings obtained from the most recent DHCP attempt. This should
improve conformance to the principle of least astonishment.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow values to be read from PCI configuration space using the syntax
${pci/<busdevfn>.<offset>.<length>}
where <busdevfn> is the bus:dev.fn address of the PCI device
(expressed as a single integer, as returned by ${net0/busloc}),
<offset> is the offset within PCI configuration space, and <length> is
the length within PCI configuration space.
Values are returned in reverse byte order, since PCI configuration
space is little-endian by definition.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move VMWARE_SETTINGS build configuration option from config/sideband.h
to a new config/settings.h.
Existing instances of config/local/sideband.h will not be affected,
since config.c still #includes config/sideband.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow network device's "busloc" setting to be formatted as a PCI
bus:dev.fn address using e.g. ${net0/busloc:busdevfn}.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hex_decode() to parse "hex" and "hexhyp" settings. Note that this
parser is stricter than the old parser; it now requires exactly two
hex digits for each byte. (The old parser was based upon strtoul()
and so would allow leading whitespace and a leading plus or minus
sign.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic hex_decode() routine which can be shared between the
Base16 code and the "hex" and "hexhyp" settings parsers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On large networks with substantial numbers of monitoring agents,
unwanted TCP connection attempts may end up flooding iPXE's ARP cache.
Fix by silently dropping packets received for unrecognised TCP
connections. This should not cause problems, since many firewalls
will also silently drop any such packets.
Reported-by: Jarrod Johnson <jarrod.b.johnson@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Locate the settings block containing the filename, and search only
that settings block for the next-server address. This avoids problems
caused by misconfigured DHCP servers which provide a next-server
address (often defaulting to the DHCP server's own IP address) even
when not providing a filename.
Originally-implemented-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc 4.8 and 4.9 fail to compile pxe_call.c with the error "bp cannot
be used in asm here". Other points in the codebase which use "ebp" in
the asm clobber list do not seem to be affected.
Unfortunately gcc provides no way to specify %ebp as an output
register, so we cannot use this as a workaround. The only viable
solution is to explicitly push/pop %ebp within the asm itself. This
is ugly for two reasons: firstly, it may be unnecessary; secondly, it
may cause gcc to generate invalid %esp-relative addresses if the asm
happens to use memory operands. This specific block of asm uses no
memory operands and so will not generate invalid code.
Reported-by: Daniel P. Berrange <berrange@redhat.com>
Reported-by: Christian Hesse <list@eworm.de>
Originally-fixed-by: Christian Hesse <list@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of Linux apparently complain if initrds are not aligned
to a page boundary. Fix by changing INITRD_ALIGN from 4 bytes to 4096
bytes.
The amount of padding at the end of each initrd will now often be
sufficient to allow the cpio header to be prepended without crossing
an alignment boundary. The final location of the initrd may therefore
end up being slightly higher than the post-shuffle location.
bzimage_load_initrd() must therefore now copy the initrd body prior to
copying the cpio header, otherwise the start of the initrd body may be
overwritten by the cpio header. (Note that the guarantee that an
initrd will never need to overwrite an initrd at a higher location
still holds, since the overall length of each initrd cannot decrease
as a result of adding a cpio header.)
Reported-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RFC2560 mandates that a valid OCSP response will contain exactly one
relevant certificate. However, some OCSP responders include
extraneous certificates. iPXE currently assumes that the first
certificate in the OCSP response is the relevant certificate; OCSP
checks will therefore fail if the responder includes the extraneous
certificates before the relevant certificate.
Fix by using the responder ID to identify the relevant certificate.
Reported-by: Christian Stroehmeier <stroemi@mail.uni-paderborn.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
realtek_destroy_ring() currently does nothing if the card is operating
in legacy (pre-RTL8139C+) mode. In particular, the producer and
consumer counters are incorrectly left holding their current values.
Virtual hardware (e.g. the emulated RTL8139 in qemu and similar VMs)
is tolerant of this behaviour, but real hardware will fail to transmit
if the descriptors are not used in the correct order.
Fix by resetting the producer and consumer counters in
realtek_destroy_ring() even if the card is operating in legacy mode.
Reported-by: Gelip <mrgelip@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 2422647 ("[prefix] Allow prefix to specify an arbitrary maximum
address for relocation") introduced a regression into the UNDI ROM
loader by preserving an extra register on the stack without modifying
the %sp-relative addresses used in the routine.
Fix by correcting the %sp-relative addresses to allow for the extra
preserved variable.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When the $(eval) function is available (in GNU make >= 3.80), we can
evaluate many of the dynamically-generated Makefile rules directly.
This avoids generating a few hundred Makefile fragments in the
filesystem, and so speeds up the build process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a certificate chain contains no certificate which can be validated
as a standalone certificate (i.e. contains no trusted root
certificates or previously-validated certificates) then iPXE will
currently return a fixed error EACCES_UNTRUSTED. This masks the
actual errors obtained when attempting to validate each certificate as
a standalone certificate, and so makes troubleshooting difficult for
the end user.
Fix by instead returning the error obtained when attempting to
validate the final certificate in the chain as a standalone
certificate. This error is most likely (though not guaranteed) to
represent the "real" problem.
Reported-by: Sven Dreyer <sven@dreyer-net.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Extend the syntax for numerical SMBIOS settings from
smbios/<type>.<offset>.<length>
to
smbios/[<instance>.]<type>.<offset>.<length>
Where SMBIOS provides multiple structures with the same <type>, this
extended syntax allows for access to structures other than the first.
If <instance> is omitted then it will default to zero, giving access
to the first instance (and so matching existing behaviour).
The 16-bit SMBIOS handle (which is an alternative way to disambiguate
multiple instances of the same type of structure) can be accessed, if
required, using
smbios/<instance>.<type>.2.2:uint16
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Peter Pickford
Alexander Chernyakhovsky
Alex Williamson
Christian Hesse
lolipop
Thomas Miletich
Marin Hannache
Robin Smidsrød
Adrian Jamróz
Frediano Ziglio