Email from solarflare.com will stop working, so update those. Remove
email for Shradha Shah, as she is not involved with this any more.
Update copyright notices for files touched.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We surface this debugging information in cases where a cert actually
lacks an issuer, but also in cases where it *has* an issuer, but we
cannot trust it (e.g. due to issues in establishing a trust chain).
Signed-off-by: Josh McSavaney <me@mcsau.cc>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE seems to be almost alone in the UEFI world in attempting to shut
down cleanly, free resources, and leave hardware in a well-defined
reset state before handing over to the booted operating system.
The UEFI driver model does allow for graceful shutdown via
uninstallation of protocol interfaces. However, virtually no other
UEFI drivers do this, and the external code paths that react to
uninstallation are consequently poorly tested. This leads to a
proliferation of bugs found in UEFI implementations in the wild, as
described in commits such as 1295b4a ("[efi] Allow initialisation via
SNP interface even while claimed") or b6e2ea0 ("[efi] Veto the HP
XhciDxe Driver").
Try to avoid triggering such bugs by unconditionally skipping the
protocol interface uninstallation during UEFI boot services shutdown,
leaving the interfaces present but nullified and deliberately leaking
the containing memory.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
USB tethering via an iPhone is unreasonably complicated due to the
requirement to perform a pairing operation that involves establishing
a TLS session over a completely unrelated USB function that speaks a
protocol that is almost, but not quite, entirely unlike TCP.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Record the root of trust used at the point that a certificate is
validated, redefine validation as checking a certificate against a
specific root of trust, and pass an explicit root of trust when
creating a TLS connection.
This allows a custom TLS connection to be used with a custom root of
trust, without causing any validated certificates to be treated as
valid for normal purposes.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
OCSP currently calls x509_validate() with an empty root certificate
list, on the basis that the OCSP signer certificate (if existent) must
be signed directly by the issuer certificate.
Using an empty root certificate list is not required to achieve this
goal, since x509_validate() already accepts an explicit issuer
certificate parameter. The explicit empty root certificate list
merely prevents the signer certificate from being evaluated as a
potential trusted root certificate.
Remove the dummy OCSP root certificate list and use the default root
certificate list when calling x509_validate().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is nothing OID-specific about the ASN1_OID_CURSOR macro. Rename
to allow it to be used for constructing ASN.1 cursors with arbitrary
contents.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the existing certificate store to automatically append any
available issuing certificates to the selected client certificate.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Restructure the use of add_tls() to insert a TLS filter onto an
existing interface. This allows for the possibility of using
add_tls() to start TLS on an existing connection (as used in several
protocols which will negotiate the choice to use TLS before the
ClientHello is sent).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generalise the filter interface insertion logic from block_translate()
and expose as intf_insert(), allowing a filter interface to be
inserted on any existing interface.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The HP XhciDxe driver (observed on an HP EliteBook 840 G6) does not
respond correctly to driver disconnection, and will leave the PciIo
protocol instance opened with BY_DRIVER attributes even after
returning successfully from its Stop() method. This prevents iPXE
from subsequently connecting to the PCI device handle.
Veto this driver if the iPXE build includes a native xHCI driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some UEFI drivers (observed with the "Usb Xhci Driver" on an HP
EliteBook) are particularly badly behaved: they cannot be unloaded and
will leave handles opened with BY_DRIVER attributes even after
disconnecting the driver, thereby preventing a replacement iPXE driver
from opening the handle.
Allow such drivers to be vetoed by falling back to a brute-force
mechanism that will disconnect the driver from all handles, uninstall
the driver binding protocol (to prevent it from attaching to any new
handles), and finally close any stray handles that the vetoed driver
has left open.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most veto checks are likely to use the manufacturer name and driver
name, so pass these as parameters to minimise code duplication.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow external code to dump the information for an opened protocol
information entry via DBG_EFI_OPENER() et al.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some devices (e.g. xHCI USB host controllers) may require the use of
large areas of host memory for private use by the device. These
allocations cannot be satisfied from iPXE's limited heap space, and so
are currently allocated using umalloc() which will allocate external
system memory (and alter the system memory map as needed).
Provide dma_umalloc() to provide such allocations as part of the DMA
API, since there is otherwise no way to guarantee that the allocated
regions are usable for coherent DMA.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification does not prohibit zero-length DMA mappings.
However, there is a reasonable chance that at least one implementation
will treat it as an invalid parameter. As a precaution, avoid calling
EFI_PCI_IO_PROTOCOL.Map() with a length of zero.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Unlike netdev_rx_err(), there is no valid circumstance under which
netdev_rx() may be called with a null I/O buffer, since a call to
netdev_rx() represents the successful reception of a packet. Fix the
code comment to reflect this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
netdev_tx_err() may be called with a null I/O buffer (e.g. to record a
transmit error with no associated buffer). Avoid a potential null
pointer dereference in the DMA unmapping code path.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include a potential DMA mapping within the definition of an I/O
buffer, and move all I/O buffer DMA mapping functions from dma.h to
iobuf.h. This avoids the need for drivers to maintain a separate list
of DMA mappings for each I/O buffer that they may handle.
Network device drivers typically do not keep track of transmit I/O
buffers, since the network device core already maintains a transmit
queue. Drivers will typically call netdev_tx_complete_next() to
complete a transmission without first obtaining the relevant I/O
buffer pointer (and will rely on the network device core automatically
cancelling any pending transmissions when the device is closed).
To allow this driver design approach to be retained, update the
netdev_tx_complete() family of functions to automatically perform the
DMA unmapping operation if required. For symmetry, also update the
netdev_rx() family of functions to behave the same way.
As a further convenience for drivers, allow the network device core to
automatically perform DMA mapping on the transmit datapath before
calling the driver's transmit() method. This avoids the need to
introduce a mapping error handling code path into the typically
error-free transmit methods.
With these changes, the modifications required to update a typical
network device driver to use the new DMA API are fairly minimal:
- Allocate and free descriptor rings and similar coherent structures
using dma_alloc()/dma_free() rather than malloc_phys()/free_phys()
- Allocate and free receive buffers using alloc_rx_iob()/free_rx_iob()
rather than alloc_iob()/free_iob()
- Calculate DMA addresses using dma() or iob_dma() rather than
virt_to_bus()
- Set a 64-bit DMA mask if needed using dma_set_mask_64bit() and
thereafter eliminate checks on DMA address ranges
- Either record the DMA device in netdev->dma, or call iob_map_tx() as
part of the transmit() method
- Ensure that debug messages use virt_to_phys() when displaying
"hardware" addresses
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Redefine the value stored within a DMA mapping to be the offset
between physical addresses and DMA addresses within the mapped region.
Provide a dma() wrapper function to calculate the DMA address for any
pointer within a mapped region, thereby simplifying the use cases when
a device needs to be given addresses other than the region start
address.
On a platform using the "flat" DMA implementation the DMA offset for
any mapped region is always zero, with the result that dma_map() can
be optimised away completely and dma() reduces to a straightforward
call to virt_to_phys().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE will currently fail all SNP interface methods with EFI_NOT_READY
while the network devices are claimed for use by iPXE's own network
stack.
As of commit c70b3e0 ("[efi] Always enable recursion when calling
ConnectController()"), this exposes latent UEFI firmware bugs on some
systems at the point of calling ExitBootServices().
With recursion enabled, the MnpDxe driver will immediately attempt to
consume the SNP protocol instance provided by iPXE. Since the network
devices are claimed by iPXE at this point, the calls by MnpDxe to
Start() and Initialize() will both fail with EFI_NOT_READY.
This unfortunately triggers a broken error-handling code path in the
Ip6Dxe driver. Specifically: Ip6DriverBindingStart() will call
Ip6CreateService(), which will call Ip6ServiceConfigMnp(), which will
return an error. The subsequent error handling code path in
Ip6CreateService() simply calls Ip6CleanService(). The code in
Ip6CleanService() will attempt to leave the all-nodes multicast group,
which will fail since the group was never joined. This will result in
Ip6CleanService() returning an error and omitting most of the required
clean-up operations. In particular, the MNP protocol instance will
remain opened with BY_DRIVER attributes even though the Ip6Dxe driver
start method has failed.
When ExitBootServices() is eventually called, iPXE will attempt to
uninstall the SNP protocol instance. This results in the UEFI core
calling Ip6DriverBindingStop(), which will fail since there is no
EFI_IP6_SERVICE_BINDING_PROTOCOL instance installed on the handle.
A failure during a call to UninstallMultipleProtocolInterfaces() will
result in the UEFI core attempting to reinstall any successfully
uninstalled protocols. This is an intrinsically unsafe operation, and
represents a fundamental design flaw in UEFI. Failure code paths
cannot be required to themselves handle failures, since there is no
well-defined correct outcome of such a situation.
With a current build of OVMF, this results in some unexpected debug
messages occurring at the time that the loaded operating system calls
ExitBootServices(). With the UEFI firmware in Hyper-V, the result is
an immediate reboot.
Work around these UEFI design and implementation flaws by allowing the
calls to our EFI_SIMPLE_NETWORK_PROTOCOL instance's Start() and
Initialize() methods to return success even when the network devices
are claimed for exclusive use by iPXE. This is sufficient to allow
MnpDxe to believe that it has successfully initialised the device, and
thereby avoids the problematic failure code paths in Ip6Dxe.
Debugged-by: Aaron Heusser <aaron_heusser@hotmail.com>
Debugged-by: Pico Mitchell <pico@randomapplications.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For the physical function driver, the transmit queue needs to be
configured to be associated with the relevant physical function
number. This is currently obtained from the bus:dev.fn address of the
underlying PCI device.
In the case of a virtual machine using the physical function via PCI
passthrough, the PCI bus:dev.fn address within the virtual machine is
unrelated to the real physical function number. Such a function will
typically be presented to the virtual machine as a single-function
device. The function number extracted from the PCI bus:dev.fn address
will therefore always be zero.
Fix by reading from the Function Requester ID Information Register,
which always returns the real PCI bus:dev.fn address as used by the
physical host.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The datasheet is fairly incomprehensible in terms of identifying the
appropriate MAC address for use by the physical function driver.
Choose to read the MAC address from PRTPM_SAH and PRTPM_SAL, which at
least matches the MAC address as selected by the Linux i40e driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE will currently drop to TPL_APPLICATION whenever the current
system time is obtained via currticks(), since the system time
mechanism relies on a timer that can fire only when the TPL is below
TPL_CALLBACK.
This can cause unexpected behaviour if the system time is obtained in
the middle of an API call into iPXE by external code. For example,
MnpDxe sets up a 10ms periodic timer running at TPL_CALLBACK to poll
the underling EFI_SIMPLE_NETWORK_PROTOCOL device for received packets.
If the resulting poll within iPXE happens to hit a code path that
requires obtaining the current system time (e.g. due to reception of
an STP packet, which affects iPXE's blocked link timer), then iPXE
will end up temporarily dropping to TPL_APPLICATION. This can
potentially result in retriggering the MnpDxe periodic timer, causing
code to be unexpectedly re-entered.
Fix by recording the external TPL at any entry point into iPXE and
dropping only as far as this external TPL, rather than dropping
unconditionally to TPL_APPLICATION.
The side effect of this change is that iPXE's view of the current
system time will be frozen for the duration of any API calls made into
iPXE by external code at TPL_CALLBACK or above. Since any such
external code is already responsible for allowing execution at
TPL_APPLICATION to occur, then this should not cause a problem in
practice.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Physical addresses in debug messages are more meaningful from an
end-user perspective than potentially IOMMU-mapped I/O virtual
addresses, and have the advantage of being calculable without access
to the original DMA mapping entry (e.g. when displaying an address for
a single failed completion within a descriptor ring).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For a software UNDI, the addresses in PXE_CPB_TRANSMIT.FrameAddr and
PXE_CPB_RECEIVE.BufferAddr are host addresses, not bus addresses.
Remove the spurious (and no-op) use of virt_to_bus() and replace with
a cast via intptr_t.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification defines PXE_CPB_TRANSMIT.DataLen as excluding
the length of the media header. iPXE currently fills in DataLen as
the whole frame length (including the media header), along with
placing the media header length separately in MediaheaderLen. On some
UNDI implementations (observed using a VMware ESXi 7.0b virtual
machine), this causes transmitted packets to include 14 bytes of
trailing garbage.
Match the behaviour of the EDK2 SnpDxe driver, which fills in DataLen
as the whole frame length (including the media header) and leaves
MediaheaderLen as zero. This behaviour also violates the UEFI
specification, but is likely to work in practice since EDK2 is the
reference implementation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
b1f6c1c4
Martin Habets
Josh McSavaney
Mohammed Taha
Michael Brown