Define an API for executing very limited functions on application
processors in a multiprocessor system, along with an x86-only
implementation.
The normal iPXE runtime environment is effectively non-existent on
application processors. There is no ability to make firmware calls
(e.g. to write to a console), and there may be no stack space
available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As noted in commit 3c83843 ("[rng] Check for several functioning RTC
interrupts"), experimentation shows that Hyper-V cannot be trusted to
reliably generate RTC interrupts. (As noted in commit f3ba0fb
("[hyperv] Provide timer based on the 10MHz time reference count
MSR"), Hyper-V appears to suffer from a general problem in reliably
generating any legacy interrupts.) An alternative entropy source is
therefore required for an image that may be used in a Hyper-V Gen1
virtual machine.
The x86 RDRAND instruction provides a suitable alternative entropy
source, but may not be supported by all CPUs. We must therefore allow
for multiple entropy sources to be compiled in, with the single active
entropy source selected only at runtime.
Restructure the internal entropy API to allow a working entropy source
to be detected and chosen at runtime.
Enable the RDRAND entropy source for all x86 builds, since it is
likely to be substantially faster than any other source.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently assumes that DMA-capable devices can directly address
physical memory using host addresses. This assumption fails when
using an IOMMU.
Define an internal DMA API with two implementations: a "flat"
implementation for use in legacy BIOS or other environments in which
flat physical addressing is guaranteed to be used and all allocated
physical addresses are guaranteed to be within a 32-bit address space,
and an "operations-based" implementation for use in UEFI or other
environments in which DMA mapping may require bus-specific handling.
The purpose of the fully inlined "flat" implementation is to allow the
trivial identity DMA mappings to be optimised out at build time,
thereby avoiding an increase in code size for legacy BIOS builds.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Abstract out the ability to reboot the system to a separate reboot()
function (with platform-specific implementations), add an EFI
implementation, and make the existing "reboot" command available under
EFI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ANS X9.82 specifies several Approved Sources of Entropy Input (SEI).
One such SEI uses an entropy source as the Source of Entropy Input,
condensing each entropy source output after each GetEntropy call.
This can be implemented relatively cheaply in iPXE and avoids the need
to allocate potentially very large buffers.
(Note that the terms "entropy source" and "Source of Entropy Input"
are not synonyms within the context of ANS X9.82.)
Use the iPXE API mechanism to allow entropy sources to be selected at
compilation time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The block device interface used in gPXE predates the invention of even
the old gPXE data-transfer interface, let alone the current iPXE
generic asynchronous interface mechanism. Bring this old code up to
date, with the following benefits:
o Block device commands can be cancelled by the requestor. The INT 13
layer uses this to provide a global timeout on all INT 13 calls,
with the result that an unexpected passive failure mode (such as
an iSCSI target ACKing the request but never sending a response)
will lead to a timeout that gets reported back to the INT 13 user,
rather than simply freezing the system.
o INT 13,00 (reset drive) is now able to reset the underlying block
device. INT 13 users, such as DOS, that use INT 13,00 as a method
for error recovery now have a chance of recovering.
o All block device commands are tagged, with a numerical tag that
will show up in debugging output and in packet captures; this will
allow easier interpretation of bug reports that include both
sources of information.
o The extremely ugly hacks used to generate the boot firmware tables
have been eradicated and replaced with a generic acpi_describe()
method (exploiting the ability of iPXE interfaces to pass through
methods to an underlying interface). The ACPI tables are now
built in a shared data block within .bss16, rather than each
requiring dedicated space in .data16.
o The architecture-independent concept of a SAN device has been
exposed to the iPXE core through the sanboot API, which provides
calls to hook, unhook, boot, and describe SAN devices. This
allows for much more flexible usage patterns (such as hooking an
empty SAN device and then running an OS installer via TFTP).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the tap driver that can be used like:
$ ./ipxe.linux --net tap,if=tap0,mac=00:0c:29:c5:39:a1
The if setting is mandatory.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There exists an smbios userspace library so implementing this is
probably possible, but doesn't seem really important to have in
userspace. Hence provide a dummy implementation returning an error.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add user access API for linux.
On linux userspace virtual == user == phys addresses. Physical
addresses also being the same is wrong, but there is no general way of
converting userspace addresses to physical as what appears to be
contiguous in userspace is physically fragmented. Currently only the
DMA memory is special-cased, but its conversion to bus addresses is
done in phys_to_bus. This is known to break virtio as it is passing
phys addresses to the virtual device.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add linux console using stdin/out. Configure the attached terminal for
readline use.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add makefiles, ld scripts and default config for linux platform for
both i386 and x86_64.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Marin Hannache
Piotr Jaroszyński