Provide a generic raw image prefix, which assumes that the iPXE image
has been loaded in its entirety on a paragraph boundary.
The resulting .raw image can be loaded via RPL using an rpld.conf file
such as:
HOST {
ethernet = 00:00:00:00:00:00/6;
FILE {
path="ipxe.raw";
load=0x2000;
};
execute=0x2000;
};
Debugged-by: Johannes Heimansberg <git@jhe.dedyn.io>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A zero-length initrd file will currently cause an endless loop during
reshuffling as the empty image is repeatedly swapped with itself.
Fix by terminating the inner loop before considering an image as a
candidate to be swapped with itself.
Reported-by: Pico Mitchell <pico@randomapplications.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Split out the portions of cachedhcp.c that can be shared between BIOS
and UEFI (both of which can provide a buffer containing a previously
obtained DHCP packet, and neither of which provide a means to
determine the length of this DHCP packet).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of GNU ld (observed with binutils 2.36 on Arch Linux)
introduce a .note.gnu.property section marked as loadable at a high
address and with non-empty contents. This adds approximately 128MB of
garbage to the BIOS .usb disk images.
Fix by using a custom linker script for the prefix-only binaries such
as the USB disk partition table and MBR, in order to allow unwanted
sections to be explicitly discarded.
Reported-by: Christian Hesse <mail@eworm.de>
Tested-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The semantics of the assembler's .align directive vary by CPU
architecture. For the ARM builds, it specifies a power of two rather
than a number of bytes. This currently leads to the .einfo entries
(which do not appear in the final binary) having an alignment of 256
bytes for the ARM builds.
Fix by switching to the GNU-specific directive .balign, which is
consistent across architectures
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several distributions include versions of gcc that are patched to
create position-independent executables by default. These have caused
multiple problems over the years: see e.g. commits fe61f6d ("[build]
Fix compilation when gcc is patched to default to -fPIE -Wl,-pie"),
5de1346 ("[build] Apply the "-fno-PIE -nopie" workaround only to i386
builds"), 7c395b0 ("[build] Use -no-pie on newer versions of gcc"),
and decee20 ("[build] Disable position-independent code for ARM64 EFI
builds").
The build system currently attempts to work around these mildly broken
patched versions of gcc for the i386 and arm64 architectures. This
misses the relatively obscure bin-x86_64-pcbios build platform, which
turns out to also require the same workaround.
Attempt to preempt the next such required workaround by moving the
existing i386 version to apply to all platforms and all architectures,
unless -fpie has been requested explicitly by another Makefile (as is
done by arch/x86_64/Makefile.efi).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a few more ABSOLUTE() expressions to convince the FreeBSD linker
that already-absolute symbols are, in fact, absolute.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of objcopy will spuriously complain when asked to
extract the .zinfo section since doing so will nominally alter the
load addresses of the (non-loadable) .bss.* sections.
Avoid these warnings by placing the .zinfo section at the very end of
the load memory address space.
Allocate non-overlapping load memory addresses for the (non-loadable)
.bss.* sections, in the hope of avoiding spurious warnings about
overlapping load addresses.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Consolidate the remaining logic common to initrd_init() and imgmem()
into a shared image_memory() function.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generalise util/geniso, util/gensdsk, and util/genefidsk to create a
single script util/genfsimg that can be used to build either FAT
filesystem images or ISO images.
Extend the functionality to allow for building multi-architecture UEFI
bootable ISO images and combined BIOS+UEFI images.
For example:
./util/genfsimg -o combined.iso \
bin-x86_64-efi/ipxe.efi \
bin-arm64-efi/ipxe.efi \
bin/ipxe.lkrn
would generate a hybrid image that could be used as a CDROM (or hard
disk or USB key) on legacy BIOS, x86_64 UEFI, or ARM64 UEFI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The malloc_dma() function allocates memory with specified physical
alignment, and is typically (though not exclusively) used to allocate
memory for DMA.
Rename to malloc_phys() to more closely match the functionality, and
to create name space for functions that specifically allocate and map
DMA-capable buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Define pci_ioremap() as a wrapper around ioremap() that could allow
for a non-zero address translation offset.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This change fixes the offset used when retrieving the iPXE stack
pointer after a COM32 binary returns. The iPXE stack pointer is saved
at the top of the available memory then the the top of the stack for
the COM32 binary is set just below it. However seven more items are
pushed on the COM32 stack before the entry point is invoked so when
the COM32 binary returns the location of the iPXE stack pointer is 28
(and not 24) bytes above the current stack pointer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This caused iPXE to reject images even when enough memory was
available.
Signed-off-by: David Decotigny <ddecotig@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The only remaining use case in iPXE for the CPU direction flag is in
__memcpy_reverse() where it is set to allow the use of "rep movsb" to
perform the memory copy. This matches the equivalent functionality in
the EDK2 codebase, which has functions such as InternalMemCopyMem that
also temporarily set the direction flag in order to use "rep movsb".
As noted in commit d2fb317 ("[crypto] Avoid temporarily setting
direction flag in bigint_is_geq()"), some UEFI implementations are
known to have buggy interrupt handlers that may reboot the machine if
a timer interrupt happens to occur while the direction flag is set.
Work around these buggy UEFI implementations by using the
(unoptimised) generic_memcpy_reverse() on i386 or x86_64 UEFI
platforms.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification states that the calling convention for IA-32
and x64 includes "Direction flag in EFLAGS is clear". This
specification covers only the calling convention used at the point of
calling functions annotated with EFIAPI. The specification explicitly
states that other functions (such as private functions or static
library calls) are not required to follow the UEFI calling
conventions.
The reference EDK2 implementation follows this specification. In
particular, the EDK2 interrupt handlers will clear the direction flag
before calling any EFIAPI functions, and will restore the direction
flag when returning from the interrupt handler. Some EDK2 private
library functions (most notably InternalMemCopyMem) may set the
direction flag temporarily in order to make efficient use of CPU
string operations.
The current implementation of iPXE's bigint_is_geq() for i386 and
x86_64 will similarly set the direction flag temporarily in order to
make efficient use of CPU string operations.
On some UEFI implementations (observed with a Getac RX10 tablet), a
timer interrupt that happens to occur while the direction flag is set
will reboot the machine. This very strongly indicates that the UEFI
timer interrupt handler is failing to clear the direction flag before
performing an affected operation (such as copying a block of memory).
Work around such buggy UEFI implementations by rewriting
bigint_is_geq() to avoid the use of string operations and so obviate
the requirement to temporarily set the direction flag.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of gcc (observed with the cross-compiling gcc 9.3.0 in
Ubuntu 20.04) default to enabling -fPIE. Experimentation shows that
this results in the emission of R_AARCH64_ADR_GOT_PAGE relocation
records for __stack_chk_guard. These relocation types are not
supported by elf2efi.c.
Fix by explicitly disabling position-independent code for ARM64 EFI
builds.
Debugged-by: Antony Messerli <antony@mes.ser.li>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the size of the USB disk image in the common case that
CONSOLE_INT13 is not enabled.
Originally-implemented-by: Romain Guyard <romain.guyard@mujin.co.jp>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It is currently not possible to build the all-drivers iPXE binaries
for ARM, since there is no implementation for inb(), outb(), etc.
There is no common standard for accessing I/O space on ARM platforms,
and there are almost no ARM-compatible peripherals that actually
require I/O space accesses.
Provide dummy implementations that behave as though no device is
present (i.e. ignore writes, return all bits high for reads). This is
sufficient to allow the all-drivers binaries to link, and should cause
drivers to behave as though no I/O space peripherals are present in
the system.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PCI Configuration Space contains fields prog-if at the offset 0x09,
sub-class at the offset 0x0a and base-class at the offset 0x0b (it
respects little endian). PCIR structure uses these fields in the same
order.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the subsystem IDs to be used when checking for PXE stacks with
broken interrupt support.
Suggested-by: Levi Hsieh <Levi.Hsieh@dell.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 6149e0a ("[librm] Provide symbols for inline code placed into
other sections") may cause build failures due to duplicate label names
if the compiler chooses to duplicate inline assembly code.
Fix by using the "%=" special format string to include a
guaranteed-unique number within the label name.
The "%=" will be expanded only if constraints exist for the inline
assembly. This fix therefore requires that all REAL_CODE() fragments
use a (possibly empty) constraint list.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide symbols constructed from the object name and line number for
code fragments placed into alternative sections, such as inline
REAL_CODE() assembly placed into .text16. This simplifies the
debugging task of finding the source code corresponding to a given
instruction pointer.
Note that we cannot use __FUNCTION__ since it is not a preprocessor
macro and so cannot be concatenated with string literals.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the underlying PXE stack reports an invalid IRQ number (above
IRQ_MAX), treat this as equivalent to an empty IRQ number and fall
back to using polling mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The existence of MMX and SSE is required by the System V x86_64 ABI
and so is assumed by gcc, but these registers are not preserved by our
own interrupt handlers and are unlikely to be preserved by other
context switch handlers in a boot firmware environment.
Explicitly prevent gcc from using MMX or SSE registers to avoid
potential problems due to silent register corruption.
We must remove the %xmm0-%xmm5 clobbers from the x86_64 version of
hv_call() since otherwise gcc will complain about unknown register
names. Theoretically, we should probably add code to explicitly
preserve the %xmm0-%xmm5 registers across a hypercall, in order to
guarantee to external code that these registers remain unchanged. In
practice this is difficult since SSE registers are disabled by
default: for background information see commits 71560d1 ("[librm]
Preserve FPU, MMX and SSE state across calls to virt_call()") and
dd9a14d ("[librm] Conditionalize the workaround for the Tivoli VMM's
SSE garbling").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently perform various min-entropy calculations using build-time
floating-point arithmetic. No floating-point code ends up in the
final binary, since the results are eventually converted to integers
and asserted to be compile-time constants.
Though this mechanism is undoubtedly cute, it inhibits us from using
"-mno-sse" to prevent the use of SSE registers by the compiler.
Fix by using fixed-point arithmetic instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the ACPI power management timer to be used if enabled via
TIMER_ACPI in config/timer.h. This provides an alternative timer on
systems where the standard 8254 PIT is unavailable or unreliable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When DEBUG=librm_mgmt is enabled, intercept CPU exceptions and provide
a register and stack dump, then drop to an emergency shell. Exiting
from the shell will almost certainly not work, but this provides an
opportunity to view the register and stack dump and carry out some
basic debugging.
Note that we can intercept only the first 8 CPU exceptions, since a
PXE ROM is not permitted to rebase the PIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using "ld --oformat binary" for mbr.bin and usbdisk.bin seems to cause
segmentation faults on some versions of binutils (observed on Fedora
27). Work around this problem by using ld to create an intermediate
ELF object, followed by objcopy (via the existing %.tmp -> %.bin rule)
to create the final binary.
Note that we cannot simply use a single-stage "objcopy -O binary"
since this will not process the relocation records for x86_64: see
commit 1afcccd ("[build] Do not use "objcopy -O binary" for objects
with relocation records").
Reported-by: Brent S <bts@square-r00t.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add missing FILE_LICENCE declarations to x86_64 headers based on the
corresponding i386 headers (from which the x86_64 headers were
originally derived).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Ensure that all headers (PCI, UNDI, PnP, iPXE) are aligned to at least
four bytes, so that all accesses to header fields will be correctly
aligned even when reading directly from the expansion ROM BAR.
Reported-by: Peter von Konigsmark <peter@exablaze.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We must not steal ownership from the Gen 2 UEFI firmware, since doing
so will cause an immediate system crash (most likely in the form of a
reboot).
This problem was masked before commit a0f6e75 ("[hyperv] Do not fail
if guest OS ID MSR is already set"), since prior to that commit we
would always fail if we found any non-zero guest OS identity. We now
accept a non-zero previous guest OS identity in order to allow for
situations such as chainloading from iPXE to another iPXE, and as a
prerequisite for commit b91cc98 ("[hyperv] Cope with Windows Server
2016 enlightenments").
A proper fix would be to reverse engineer the UEFI protocols exposed
within the Hyper-V Gen 2 firmware and use these to bind to the VMBus
device representing the network connection, (with the native Hyper-V
driver moved to become a BIOS-only feature).
As an interim solution, fail to initialise the native Hyper-V driver
if we detect the guest OS identity known to be used by the Gen 2 UEFI
firmware. This will cause the standard all-drivers build (ipxe.efi)
to fall back to using the SNP driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EDK2 commit 6440385 ("MdePkg/Include: Add enumeration size checks to
Base.h") enforced the UEFI specification mandate that enums should
always be 32 bits. This revealed a latent bug in iPXE, which does not
build with -fno-short-enums.
Fix by adding -fno-short-enums to CFLAGS for ARM32 EFI builds.
Reported-by: Benjamin S. Allen <bsallen@alcf.anl.gov>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The -mabi option was added in GCC 4.9. Test for the existence of this
option to allow for building with earlier versions of GCC.
Reported-by: Benjamin S. Allen <bsallen@alcf.anl.gov>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For some CPUID leaves (e.g. %eax=0x00000004), the result depends on
the input value of %ecx. Allow this subfunction number to be
specified as a parameter to the cpuid() wrapper.
The subfunction number is exposed via the ${cpuid/...} settings
mechanism using the syntax
${cpuid/<subfunction>.0x40.<register>.<function>}
e.g.
${cpuid/0.0x40.0.0x0000000b}
${cpuid/1.0x40.0.0x0000000b}
to retrieve the CPU topology information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some distributions patch gcc to generate position independent
executables by default. We currently include a workaround to check
for this and to add -fno-PIE -nopie to CFLAGS if required.
Newer patched versions of gcc require -fno-PIE -no-pie instead. Check
for both variants.
Reported-by: Nathan Rennie-Waldock <nathan.renniewaldock@gmail.com>
Originally-fixed-by: Markos Chandras <mchandras@suse.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When booting from a hard disk image (e.g. bin/ipxe.usb) within an
emulator such as QEMU, the disk may not exist beyond the end of the
image. Limit all reads to the length of the image to avoid spurious
errors when loading the iPXE image.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An "enlightened" external bootloader (such as Windows Server 2016's
winload.exe) may take ownership of the Hyper-V connection before all
INT 13 operations have been completed. When this happens, all VMBus
devices are implicitly closed and we are left with a non-functional
network connection.
Detect when our Hyper-V connection has been lost (by checking the
SynIC message page MSR). Reclaim ownership of the Hyper-V connection
and reestablish any VMBus devices, without disrupting any existing
iPXE state (such as IPv4 settings attached to the network device).
Windows Server 2016 will not cleanly take ownership of an active
Hyper-V connection. Experimentation shows that we can quiesce by
resetting only the SynIC message page MSR; this results in a
successful SAN boot (on a Windows 2012 R2 physical host). Choose to
quiesce by resetting (almost) all MSRs, in the hope that this will be
more robust against corner cases such as a stray synthetic interrupt
occurring during the handover.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older operating systems (e.g. RHEL6) use a non-default filename
on the root disk and rely on setting an EFI variable to point to the
bootloader. This does not work when performing a SAN boot on a
machine where the EFI variable is not present.
Fix by allowing a non-default filename to be specified via the
"sanboot --filename" option or the "san-filename" setting. For
example:
sanboot --filename \efi\redhat\grub.efi \
iscsi:192.168.0.1::::iqn.2010-04.org.ipxe.demo:rhel6
or
option ipxe.san-filename code 188 = string;
option ipxe.san-filename "\\efi\\redhat\\grub.efi";
option root-path "iscsi:192.168.0.1::::iqn.2010-04.org.ipxe.demo:rhel6";
Originally-implemented-by: Vishvananda Ishaya Abrams <vish.ishaya@oracle.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Describe all SAN devices via ACPI tables such as the iBFT. For tables
that can describe only a single device (i.e. the aBFT and sBFT), one
table is installed per device. For multi-device tables (i.e. the
iBFT), all devices are described in a single table.
An underlying SAN device connection may be closed at the time that we
need to construct an ACPI table. We therefore introduce the concept
of an "ACPI descriptor" which enables the SAN boot code to maintain an
opaque pointer to the underlying object, and an "ACPI model" which can
build tables from a list of such descriptors. This separates the
lifecycles of ACPI descriptions from the lifecycles of the block
device interfaces, and allows for construction of the ACPI tables even
if the block device interface has been closed.
For a multipath SAN device, iPXE will wait until sufficient
information is available to describe all devices but will not wait for
all paths to connect successfully. For example: with a multipath
iSCSI boot iPXE will wait until at least one path has become available
and name resolution has completed on all other paths. We do this
since the iBFT has to include IP addresses rather than DNS names. We
will commence booting without waiting for the inactive paths to either
become available or close; this avoids unnecessary boot delays.
Note that the Linux kernel will refuse to accept an iBFT with more
than two NIC or target structures. We therefore describe only the
NICs that are actually required in order to reach the described
targets. Any iBFT with at most two targets is therefore guaranteed to
describe at most two NICs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The INT13 console type (CONSOLE_INT13) autodetects at initialisation
time a magic partition to be used for logging iPXE console output. If
the INT13 drive number mapping is subsequently changed (e.g. because
iPXE was used to perform a SAN boot), then the console logging output
will be written to the incorrect disk.
Fix by recording the INT13 vector at initialisation time, and using
this original vector to emulate INT13 calls for all subsequent
accesses. This should be robust against drive remapping performed
either by ourselves or by another bootloader (e.g. a chainloaded
undionly.kpxe which then performs a SAN boot).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some partition tables have partitions that are not aligned to a
cylinder boundary, which confuses the current geometry guessing logic.
Enhance the existing logic to ensure that we never reduce our guesses
for the number of heads or sectors per track, and add extra logic to
calculate the exact number of sectors per track if we find a partition
that starts within cylinder zero.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add basic support for multipath block devices. The "sanboot" and
"sanhook" commands now accept a list of SAN URIs. We open all URIs
concurrently. The first connection to become available for issuing
block device commands is marked as the active path and used for all
subsequent commands; all other connections are then closed. Whenever
the active path fails, we reopen all URIs and repeat the process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As of commit 10d19bd ("[pxe] Always retrieve cached DHCPACK and apply
to relevant network device"), the UNDI driver has been the only user
of pxeparent_call(). Remove the unnecessary layer of abstraction by
refactoring this code back into undinet.c, and fix the ability of
undiisr.S to fall back to chaining to the original handler if we were
unable to unhook our own ISR.
This effectively reverts commit 337e1ed ("[pxe] Separate parent PXE
API caller from UNDINET driver").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The concept of the SAN drive number is meaningful only in a BIOS
environment, where it represents the INT13 drive number (0x80 for the
first hard disk). We retain this concept in a UEFI environment to
allow for a simple way for iPXE commands to refer to SAN drives.
Centralise the concept of the default drive number, since it is shared
between all supported environments.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
INT 13 calls return a status value via %ah, with CF set if %ah is
non-zero (indicating an error). Our wrappers zero the whole of %ax if
CF is clear, to allow C code (which has no easy access to CF) to
simply test for a non-zero status to detect an error.
The current code assigns the returned status to a uint8_t, effectively
testing %al rather than %ah. Fix by treating the returned status as a
uint16_t instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid using a zero sector count to guess the disk geometry, since that
would result in a division by zero when calculating the number of
cylinders.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When running on AMD platforms, the legacy hardware emulation is
extremely unreliable. In particular, the IRQ0 timer interrupt is
likely to simply stop working, resulting in a total failure of any
code that relies on timers (such as DHCP retransmission attempts).
Work around this by using the 10MHz time counter provided by Hyper-V
via an MSR. (This timer can be tested in KVM via the command-line
option "-cpu host,hv_time".)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the active timer (providing udelay() and currticks()) to be
selected at runtime based on probing during the INIT_EARLY stage of
initialisation.
TICKS_PER_SEC is now a fixed compile-time constant for all builds, and
is independent of the underlying clock tick rate. We choose the value
1024 to allow multiplications and divisions on seconds to be converted
to bit shifts.
TICKS_PER_MS is defined as 1, allowing multiplications and divisions
on milliseconds to be omitted entirely. The 2% inaccuracy in this
definition is negligible when using the standard BIOS timer (running
at around 18.2Hz).
TIMER_RDTSC now checks for a constant TSC before claiming to be a
usable timer. (This timer can be tested in KVM via the command-line
option "-cpu host,+invtsc".)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This code largely inspired by tap.c. Allows for testing iPXE on real
NICs from within Linux. For example:
make bin-x86_64-linux/af_packet.linux
valgrind ./bin-x86_64-linux/af_packet.linux --net af_packet,if=eth3
Tested as x86_64 and i386 binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When searching for an UNDI ROM to match against a PCI device, search
in order of increasing ROM address (within the 128kB BIOS option ROM
area). This is likely (though not guaranteed) to match the order of
the original enumeration performed by the BIOS, which is in turn
likely to match the order of enumeration on the PCI bus.
Since we load at most one UNDI ROM, the net result is that we increase
our chances of loading the ROM corresponding to the selected PCI
device (rather than loading a ROM corresponding to a higher-numbered
PCI device with the same vendor and device IDs.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "progress" macro can be used only from within the .prefix section.
At the point of calling relocate(), we are running in .text16 and so
the near call to print_message() will end up calling a random function
somewhere in .text16.
Interestingly, this problem has remained unnoticed for some time. It
is rare to build with DEBUG=libprefix. In the few cases that it has
been used during development, the randomly selected function in
.text16 seems to have been a harmless no-op with no visible
side-effects (beyond the unnoticed failure to print the "relocate"
progress message).
Fix by removing the futile attempt to print a progress message before
calling relocate().
Reported-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Fix the <NULL> driver name reported by "ifstat" when using the undipci
driver (due to the unnecessary extra device node inserted as a child
of the PCI device).
Remove the "UNDI-" prefix from device names since the driver name is
also now visible via "ifstat", and tidy up the device name to match
the format used by standard PCI devices.
The output from "ifstat" now resembles:
iPXE> ifstat
net0: 52:54:00:12:34:56 using undipci on 0000:00:03.0
iPXE> ifstat
net0: 52:54:00:12:34:56 using undionly on 0000:00:03.0
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UNDI loader entry point is very likely to be called after POST,
when there is a high chance that the PMM-allocated image source area
and decompression area have been reused by something else.
In particular, using an iPXE .iso to test a separate iPXE ROM's UNDI
loader entry point in a qemu VM is likely to crash. SeaBIOS allocates
PMM blocks from close to the top of memory and so these blocks have a
high chance of colliding with the runtime addresses subsequently
chosen by the non-ROM iPXE by scanning the INT 15,e820 memory map.
The standard romprefix.S has no choice about relying on the
PMM-allocated image source area, since it has no other way to retrieve
its compressed payload.
In mromprefix.S, the image source area functions only as an optional
buffer used to avoid repeated reads from the (potentially slow)
expansion ROM BAR by the decompression code. We can therefore always
set %esi=0 when calling install_prealloc from the UNDI loader entry
point, and simply fall back to reading directly from the expansion ROM
BAR.
We can always set %edi=0 when calling install_prealloc from the UNDI
loader entry point. This will behave as though the decompression area
PMM allocation failed, and will therefore use INT 15,88 to find a
temporary decompression area somewhere close to 64MB. This is by no
means guaranteed to be safe from collisions, but it's probably safer
on balance than the PMM-allocated address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allocate base memory (by decreasing the free base memory counter)
before calling the UNDI loader entry point, to minimise surprises for
the UNDI loader code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 71560d1 ("[librm] Preserve FPU, MMX and SSE state across calls
to virt_call()") added FXSAVE and FXRSTOR instructions to iPXE. In
KVM virtual machines, these instructions execute fine as long as the
host CPU supports the "unrestricted_guest" feature (that is, it can
virtualize big real mode natively). On older host CPUs however, KVM
has to emulate big real mode, and it currently doesn't implement
FXSAVE emulation.
Upstream QEMU rebuilt iPXE at commit 0418631 ("[thunderx] Fix
compilation with older versions of gcc") which is a descendant of
commit 71560d1 (see above).
This was done in QEMU commit ffdc5a2 ("ipxe: update submodule from
4e03af8ec to 041863191"). The resultant binaries were bundled with
the QEMU v2.7.0 release; see QEMU commit c52125a ("ipxe: update
prebuilt binaries").
This distributed the iPXE workaround for the Tivoli VMM bug to a
number of KVM users with old host CPUs, causing KVM emulation failures
(guest crashes) for them while netbooting.
Make the FXSAVE and FXRSTOR instructions conditional on a new feature
test macro called TIVOLI_VMM_WORKAROUND. Define the macro by default.
There is prior art for an assembly file including config/general.h:
see arch/x86/prefix/romprefix.S. Also, TIVOLI_VMM_WORKAROUND seems to
be a good fit for the "Obscure configuration options" section in
config/general.h.
Cc: Bandan Das <bsd@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Greg <rollenwiese@yahoo.com>
Cc: Michael Brown <mcb30@ipxe.org>
Cc: Michael Prokop <launchpad@michael-prokop.at>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Pickford <arch@netremedies.ca>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Ref: https://bugs.archlinux.org/task/50778
Ref: https://bugs.launchpad.net/qemu/+bug/1623276
Ref: https://bugzilla.proxmox.com/show_bug.cgi?id=1182
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1356762
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The initrd_addr_max field represents the highest byte address that may
be used to hold initrd images, and is therefore almost certainly not
aligned to a page boundary: a typical value might be 0x7fffffff.
Fix the address calculations to ensure that the initrd images are
always aligned to a page boundary.
Reported-by: Sitsofe Wheeler <sitsofe@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ACPI power off sequence may not take effect immediately. Delay
for one second, to eliminate potentially confusing log messages such
as "Could not power off: Error 0x43902001 (http://ipx".
Reported-by: Leonid Vasetsky <leonidv@velostrata.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some platforms (observed in a small subset of Microsoft Azure
(Hyper-V) virtual machines), the RTC appears to be incapable of
generating an interrupt via the legacy PIC. The RTC status registers
show that a periodic interrupt has been asserted, but the PIC IRR
shows that IRQ8 remains inactive.
On such systems, iPXE will currently freeze during the "iPXE
initialising devices..." message.
Work around this problem by checking that RTC interrupts are being
raised before returning from rtc_entropy_enable(). If no interrupt is
seen within 100ms, then we assume that the RTC interrupt mechanism is
broken. In these circumstances, iPXE will continue to initialise but
any subsequent attempt to generate entropy will fail. In particular,
HTTPS connections will fail with an error indicating that no entropy
is available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The vendor class identifier strings in DHCP_ARCH_VENDOR_CLASS_ID are
out of sync with the (correct) client architecture values in
DHCP_ARCH_CLIENT_ARCHITECTURE.
Fix by removing all definitions of DHCP_ARCH_VENDOR_CLASS_ID, and
instead generating the vendor class identifier string automatically
based on DHCP_ARCH_CLIENT_ARCHITECTURE and DHCP_ARCH_CLIENT_NDI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DHCPv4 and DHCPv6 share some values in common for the architecture-
specific options (such as the client system architecture type), but
use different encapsulations: DHCPv4 has a single byte for the option
length while DHCPv6 has a 16-bit field for the option length.
Move the containing DHCP_OPTION() and related wrappers from the
individual dhcp_arch.h files to dhcp.c, thus allowing for the
architecture-specific values to be reused in dhcpv6.c.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some BIOSes (observed with an HP Gen9) seem to spuriously enable
interrupts at the PIC. This causes problems with NBPs such as GRUB
which use the UNDI API (thereby enabling interrupts on the NIC)
without first hooking an interrupt service routine. In this
situation, the interrupt will end up being handled by the default BIOS
ISR, which will typically just send an EOI and return. Since nothing
in this handler causes the NIC to deassert the interrupt, this will
result in an interrupt storm.
Entertainingly, some BIOSes are immune to this problem because the
default ISR sends the EOI only to the slave PIC; this effectively
disables the interrupt.
Work around this problem by disabling the interrupt on the PIC before
invoking the PXE NBP. An NBP that expects to make use of interrupts
will need to be configuring the PIC anyway, so it is probably safe to
assume that it will explicitly reenable the interrupt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There seems to be no reason for the sti/cli pair used around each call
to INT 10. Remove these instructions, so that printing debug messages
from within an ISR does not temporarily reenable interrupts.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Extend the 16-bit PCI bus:dev.fn address to a 32-bit seg🚌dev.fn
address, assuming a segment value of zero in contexts where multiple
segments are unsupported by the underlying data structures (e.g. in
the iBFT or BOFM tables).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The raw cycle counter at PMCCNTR_EL0 works in qemu but seems to always
read as zero on physical hardware (tested on Juno r1 and Cavium
ThunderX), even after ensuring that PMCR_EL0.E and PMCNTENSET_EL0.C
are both enabled.
Use CNTVCT_EL0 instead; this seems to count at a lower resolution
(tens of CPU cycles), but is usable for profiling.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Require architecture-specific code to make a deliberate choice to use
the unoptimised generic_tcpip_continue_chksum() function, if there is
no optimised version available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The IBM Tivoli Provisioning Manager for OS Deployment (also known as
TPMfOSD, Rembo-ia32, or Rembo Auto-Deploy) has a serious bug in some
older versions (observed with v5.1.1.0, apparently fixed by v7.1.1.0)
which can lead to arbitrary data corruption.
As mentioned in commit 87723a0 ("[libflat] Test A20 gate without
switching to flat real mode"), Tivoli's NBP sets up a VMM and makes
calls to the PXE stack in VM86 mode. This appears to be some kind of
attempt to run PXE API calls inside a sandbox. The VMM is fairly
sophisticated: for example, it handles our attempts to switch into
protected mode and patches our GDT so that our protected-mode code
runs in ring 1 instead of ring 0. However, it neglects to apply any
memory protections. In particular, it does not enable paging and
leaves us with 4GB segment limits. We can therefore trivially break
out of the sandbox by simply overwriting the GDT (or by modifying any
of Tivoli's VMM code or data structures).
When we attempt to execute privileged instructions (such as "lidt"),
the CPU raises an exception and control is passed to the Tivoli VMM.
This may result in a call to Tivoli's memcpy() function.
Tivoli's memcpy() function includes optimisations which use the SSE
registers %xmm0-%xmm3 to speed up aligned memory copies.
Unfortunately, the Tivoli VMM's exception handler does not save or
restore %xmm0-%xmm3. The net effect of this bug in the Tivoli VMM is
that any privileged instruction (such as "lidt") issued by iPXE may
result in unexpected corruption of the %xmm0-%xmm3 registers.
Even more unfortunately, this problem affects the code path taken in
response to a hardware interrupt from the NIC, since that code path
will call PXENV_UNDI_ISR. The net effect therefore becomes that any
NIC hardware interrupt (e.g. due to a received packet) may result in
unexpected corruption of the %xmm0-%xmm3 registers.
If a packet arrives while Tivoli is in the middle of using its
memcpy() function, then the unexpected corruption of the %xmm0-%xmm3
registers will result in unexpected corruption in the destination
buffer. The net effect therefore becomes that any received packet may
result in a 16-byte block of corruption somewhere in any data that
Tivoli copied using its memcpy() function.
We can work around this bug in the Tivoli VMM by saving and restoring
the %xmm0-%xmm3 registers across calls to virt_call(). To work around
the problem, we need to save registers before attempting to execute
any privileged instructions, and ensure that we attempt no further
privileged instructions after restoring the registers.
This is less simple than it may sound. We can use the "movups"
instruction to save and restore individual registers, but this will
itself generate an undefined opcode exception if SSE is not currently
enabled according to the flags in %cr0 and %cr4. We can't access %cr0
or %cr4 before attempting the "movups" instruction, because access a
control register is itself a privileged instruction (which may
therefore trigger corruption of the registers that we're trying to
save).
The best solution seems to be to use the "fxsave" and "fxrstor"
instructions. If SSE is not enabled, then these instructions may fail
to save and restore the SSE register contents, but will not generate
an undefined opcode exception. (If SSE is not enabled, then we don't
really care about preserving the SSE register contents anyway.)
The use of "fxsave" and "fxrstor" introduces an implicit assumption
that the CPU supports SSE instructions (even though we make no
assumption about whether or not SSE is currently enabled). SSE was
introduced in 1999 with the Pentium III (and added by AMD in 2001),
and is an architectural requirement for x86_64. Experimentation with
current versions of gcc suggest that it may generate SSE instructions
even when using "-m32", unless an explicit "-march=i386" or "-mno-sse"
is used to inhibit this. It therefore seems reasonable to assume that
SSE will be supported on any hardware that might realistically be used
with new iPXE builds.
As a side benefit of this change, the MMX register %mm0 will now be
preserved across virt_call() even in an i386 build of iPXE using a
driver that requires readq()/writeq(), and the SSE registers
%xmm0-%xmm5 will now be preserved across virt_call() even in an x86_64
build of iPXE using the Hyper-V netvsc driver.
Experimentation suggests that this change adds around 10% to the
number of cycles required for a do-nothing virt_call(), most of which
are due to the extra bytes copied using "rep movsb". Since the number
of bytes copied is a compile-time constant local to librm.S, we could
potentially reduce this impact by ensuring that we always copy a whole
number of dwords and so can use "rep movsl" instead of "rep movsb".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some PXE NBPs are known to make PXE API calls with very little space
available on the real-mode stack. For example, the Rembo-ia32 NBP
from some versions of IBM's Tivoli Provisioning Manager for Operating
System Deployment (TPMfOSD) will issue calls with the real-mode stack
placed at 0000:03d2; this is at the end of the interrupt vector table
and leaves only 498 bytes of stack space available before overwriting
the hardware IRQ vectors. This limits the amount of state that we can
preserve before transitioning to protected mode.
Work around these challenging conditions by preserving everything
other than the initial register dump in a temporary static buffer
within our real-mode data segment, and copying the contents of this
buffer to the protected-mode stack.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some end-user configurations have been observed in which the first NBP
(such as GRUB2) uses the UNDI API and then transfers control to a
second NBP (such as pxelinux) which uses the UDP API. The first NBP
closes the network device using PXENV_UNDI_CLOSE, which renders the
UDP API unable to transmit or receive packets.
The correct behaviour under these circumstances is (as often) simply
not documented by the PXE specification. Testing with the Intel PXE
stack suggests that PXENV_UDP_OPEN will implicitly reopen the network
device if necessary, so match this behaviour.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The DHCP option 175.189 has been defined (by us) since 2006 as
containing the drive number to be used for a SAN boot, but has never
been automatically used as such by iPXE.
Use this option (if specified) to override the default SAN drive
number.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Interpret the maximum drive number (0xff for hard disks, 0x7f for
floppy disks) as meaning "use natural drive number".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The mbr.bin and usbdisk.bin standalone blobs are currently generated
using "objcopy -O binary", which does not process relocation records.
For the i386 build, this does not matter since the section start
address is zero and so the ".rel" relocation records are effectively
no-ops anyway.
For the x86_64 build, the ".rela" relocation records are not no-ops,
since the addend is included as part of the relocation record (rather
than inline). Using "objcopy -O binary" will silently discard the
relocation records, with the result that all symbols are effectively
given a value of zero.
Fix by using "ld --oformat binary" instead of "objcopy -O binary" to
generate mbr.bin and usbdisk.bin.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some architectures (such as ARM) the "@" character is used as a
comment delimiter. A section type argument such as "@progbits"
therefore becomes "%progbits".
This is further complicated by the fact that the "%" character has
special meaning for inline assembly when input or output operands are
used, in which cases "@progbits" becomes "%%progbits".
Allow the section type character(s) to be defined via Makefile
variables.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 196f0f2 ("[librm] Convert prot_call() to a real-mode near
call") introduced a regression in which any deliberate modification to
the low 16 bits of the CPU flags (in struct i386_all_regs) would be
overwritten with the original flags value at the time of entry to
prot_call().
The regression arose because the alignment requirements of the
protected-mode stack necessitated the insertion of two bytes of
padding immediately below the prot_call() return address. The
solution chosen was to extend the existing "pushfl / popfl" pair to
"pushfw;pushfl / popfl;popfw". The extra "pushfw / popfw" appears at
first glance to be a no-op, but fails to take into account the fact
that the flags restored by popfl may have been deliberately modified
by the protected-mode function.
Fix by replacing "pushfw / popfw" with "pushw %ss / popw %ss". While
%ss does appear within struct i386_all_regs, any modification to the
stored value has always been ignored by prot_call() anyway.
The most visible symptom of this regression was that SAN booting would
fail since every INT 13 call would be chained to the original INT 13
vector.
Reported-by: Vishvananda Ishaya <vishvananda@gmail.com>
Reported-by: Jamie Thompson <forum.ipxe@jamie-thompson.co.uk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When running the 64-bit BIOS version of iPXE, restrict external memory
allocations to the low 4GB to ensure that allocations (such as for
initrds) fall within our identity-mapped memory region, and will be
accessible to the potentially 32-bit operating system.
Move largest_memblock() back to memtop_umalloc.c, since this change
imposes a restriction that applies only to BIOS builds.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for running the BIOS version of iPXE in 64-bit long mode.
A 64-bit BIOS version of iPXE can be built using e.g.
make bin-x86_64-pcbios/ipxe.usb
make bin-x86_64-pcbios/8086100e.mrom
The 64-bit BIOS version should appear to function identically to the
normal 32-bit BIOS version. The physical memory layout is unaltered:
iPXE is still relocated to the top of the available 32-bit address
space. The code is linked to a virtual address of 0xffffffffeb000000
(in the negative 2GB as required by -mcmodel=kernel), with 4kB pages
created to cover the whole of .textdata. 2MB pages are created to
cover the whole of the 32-bit address space.
The 32-bit portions of the code run with VIRTUAL_CS and VIRTUAL_DS
configured such that truncating a 64-bit virtual address gives a
32-bit virtual address pointing to the same physical location.
The stack pointer remains as a physical address when running in long
mode (although the .stack section is accessible via the negative 2GB
virtual address); this is done in order to simplify the handling of
interrupts occurring while executing a portion of 32-bit code with
flat physical addressing via PHYS_CODE().
Interrupts may be enabled in either 64-bit long mode, 32-bit protected
mode with virtual addresses, 32-bit protected mode with physical
addresses, or 16-bit real mode. Interrupts occurring in any mode
other than real mode will be reflected down to real mode and handled
by whichever ISR is hooked into the BIOS interrupt vector table.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a 64-bit build, the entirety of the 32-bit address space is
identity-mapped and so any valid physical address may immediately be
used as a virtual address. Conversely, a virtual address that is
already within the 32-bit address space may immediately be used as a
physical address.
A valid virtual address that lies outside the 32-bit address space
must be an address within .textdata, and so can be converted to a
physical address by adding virt_offset.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical locations of .textdata, .text16 and .data16 are constant
from the point of view of C code. Mark the relevant variables as
constant to allow gcc to optimise out redundant reads.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No callers of prot_to_phys, phys_to_prot, or intr_to_prot require the
flags to be preserved. Remove the unnecessary pushfl/popfl pairs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a phys_call() wrapper function (analogous to the existing
real_call() wrapper function) for calling code with flat physical
addressing, and use this wrapper within the PHYS_CODE() macro.
Move the relevant functionality inside librm.S, where it more
naturally belongs.
The COMBOOT code currently uses explicit calls to _virt_to_phys and
_phys_to_virt. These will need to be rewritten if our COMBOOT support
is ever generalised to be able to run in a 64-bit build.
Specifically:
- com32_exec_loop() should be restructured to use PHYS_CODE()
- com32_wrapper.S should be restructured to use an equivalent of
prot_call(), passing parameters via a struct i386_all_regs
- there appears to be no need for com32_wrapper.S to switch between
external and internal stacks; this could be omitted to simplify
the design.
For now, librm.S continues to expose _virt_to_phys and _phys_to_virt
for use by com32.c and com32_wrapper.S. Similarly, librm.S continues
to expose _intr_to_virt for use by gdbidt.S.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of binutils have issues with both the use of
PROVIDE() and the interpretation of numeric literals within a section
description.
Work around these older versions by defining the required numeric
literals outside of any section description, and by automatically
determining whether or not to generate extra space for page tables
rather than relying on LDFLAGS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The bulk of the iPXE binary (the .textdata section) is physically
relocated at runtime to the top of the 32-bit address space in order
to allow space for an OS to be loaded. The relocation is achieved
with the assistance of segmentation: we adjust the code and data
segment bases so that the link-time addresses remain valid.
Segmentation is not available (for normal code and data segments) in
long mode. We choose to compile the C code with -mcmodel=kernel and
use a link-time address of 0xffffffffeb000000. This choice allows us
to identity-map the entirety of the 32-bit address space, and to alias
our chosen link-time address to the physical location of our .textdata
section. (This requires the .textdata section to always be aligned to
a page boundary.)
We simultaneously choose to set the 32-bit virtual address segment
bases such that the link-time addresses may simply be truncated to 32
bits in order to generate a valid 32-bit virtual address. This allows
symbols in .textdata to be trivially accessed by both 32-bit and
64-bit code.
There is no (sensible) way in 32-bit assembly code to generate the
required R_X86_64_32S relocation records for these truncated symbols.
However, subtracting the fixed constant 0xffffffff00000000 has the
same effect as truncation, and can be represented in a standard
R_X86_64_32 relocation record. We define the VIRTUAL() macro to
abstract away this truncation operation, and apply it to all
references by 32-bit (or 16-bit) assembly code to any symbols within
the .textdata section.
We define "virt_offset" for a 64-bit build as "the value to be added
to an address within .textdata in order to obtain its physical
address". With this definition, the low 32 bits of "virt_offset" can
be treated by 32-bit code as functionally equivalent to "virt_offset"
in a 32-bit build.
We define "text16" and "data16" for a 64-bit build as the physical
addresses of the .text16 and .data16 sections. Since a physical
address within the 32-bit address space may be used directly as a
64-bit virtual address (thanks to the identity map), this definition
provides the most natural access to variables in .text16 and .data16.
Note that this requires a minor adjustment in prot_to_real(), which
accesses .text16 using 32-bit virtual addresses.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Long-mode operation will require page tables, which are too large to
sensibly fit in our .data16 segment in base memory.
Add a portion of init_librm() running in 32-bit protected mode to
provide access to high memory. Use this portion of init_librm() to
initialise the .textdata variables "virt_offset", "text16", and
"data16", eliminating the redundant (re)initialisation currently
performed on every mode transition as part of real_to_prot().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the standard "pushl $function ; pushw %cs ; call prot_call"
sequence everywhere that prot_call() is used.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a 64-bit CPU, any modification of a register by 32-bit or 16-bit
code will destroy the invisible upper 32 bits of the corresponding
64-bit register. For example: a 32-bit "pushl %eax" followed by a
"popl %eax" will zero the upper half of %rax. This differs from the
treatment of upper halves of 32-bit registers by 16-bit code: a
"pushw %ax" followed by a "popw %ax" will leave the upper 16 bits of
%eax unmodified.
Inline assembly generated using REAL_CODE() or PHYS_CODE() will
therefore have to preserve the upper halves of all registers, to avoid
clobbering registers that gcc expects to be preserved.
Output operands from REAL_CODE() and PHYS_CODE() assembly may
therefore contain undefined values in the upper 32 bits.
Fix by using explicit variable widths (e.g. uint32_t) for
non-discarded output operands, to ensure that undefined values in the
upper 32 bits of 64-bit registers are ignored.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move most arch/i386 files to arch/x86, and adjust the contents of the
Makefiles and the include/bits/*.h headers to reflect the new
locations.
This patch makes no substantive code changes, as can be seen using a
rename-aware diff (e.g. "git show -M5").
This patch does not make the pcbios platform functional for x86_64; it
merely allows it to compile without errors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit c64747d ("[librm] Speed up real-to-protected mode transition
under KVM") rounded down the .text16 segment address calculated in
alloc_basemem() to a multiple of 64 bytes in order to speed up mode
transitions under KVM.
This creates a potential discrepancy between alloc_basemem() and
free_basemem(), meaning that free_basemem() may free less memory than
was allocated by alloc_basemem().
Fix by padding the calculated sizes of both .text16 and .data16 to a
multiple of 64 bytes at build time.
Debugged-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a debug function check_bios_interrupts() to look for changes
to the interrupt vector table. This can be useful when investigating
the behaviour (including crashes) of external PXE NBPs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Dentcho Ludmilov Bankov
David Decotigny
Petr Borsodi
Laszlo Ersek