For the sake of completeness, ensure that all 32 bytes of the receive
queue context are programmed (including the unused final 8 bytes).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 8f3e648 ("[intelxl] Use one admin queue buffer per admin queue
descriptor") changed the API for intelxl_admin_command() such that the
caller now constructs the command directly within the next available
descriptor ring entry, rather than relying on intelxl_admin_command()
to copy the descriptor to and from the descriptor ring.
This introduced a regression in intelxl_admin_switch(), since the
second and subsequent iterations of the loop will not have constructed
a valid command in the new descriptor ring entry before calling
intelxl_admin_command().
Fix by constructing the command within the loop.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When applying an ACPI-provided system-specific MAC address, apply it
to netdev->ll_addr rather than netdev->hw_addr. This allows iPXE
scripts to access the permanent MAC address via the ${netX/hwaddr}
setting (and thereby provides scripts with a mechanism to ascertain
that the NIC is using a MAC address other than its own permanent
hardware address).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some systems (observed with the Thunderbolt ports on a ThinkPad X1
Extreme Gen3 and a ThinkPad P53), if the IOMMU is enabled then the
system firmware will install an ExitBootServices notification event
that disables bus mastering on the Thunderbolt xHCI controller and all
PCI bridges, and destroys any extant IOMMU mappings. This leaves the
xHCI controller unable to perform any DMA operations.
As described in commit 236299b ("[xhci] Avoid DMA during shutdown if
firmware has disabled bus mastering"), any subsequent DMA operation
attempted by the xHCI controller will end up completing after the
operating system kernel has reenabled bus mastering, resulting in a
DMA operation to an area of memory that the hardware is no longer
permitted to access and, on Windows with the Driver Verifier enabled,
a STOP 0xE6 (DRIVER_VERIFIER_DMA_VIOLATION).
That commit avoids triggering any DMA attempts during the shutdown of
the xHCI controller itself. However, this is not a complete solution
since any attached and opened USB device (e.g. a USB NIC) may
asynchronously trigger DMA attempts that happen to occur after bus
mastering has been disabled but before we reset the xHCI controller.
Avoid this problem by installing our own ExitBootServices notification
event at TPL_NOTIFY, thereby causing it to be invoked before the
firmware's own ExitBootServices notification event that disables bus
mastering.
This unsurprisingly causes the shutdown hook itself to be invoked at
TPL_NOTIFY, which causes a fatal error when later code attempts to
raise the TPL to TPL_CALLBACK (which is a lower TPL). Work around
this problem by redefining the "internal" iPXE TPL to be variable, and
set this internal TPL to TPL_NOTIFY when the shutdown hook is invoked.
Avoid calling into an underlying SNP protocol instance from within our
shutdown hook at TPL_NOTIFY, since the underlying SNP driver may
attempt to raise the TPL to TPL_CALLBACK (which would cause a fatal
error). Failing to shut down the underlying SNP device is safe to do
since the underlying device must, in any case, have installed its own
ExitBootServices hook if any shutdown actions are required.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Tested-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the "system MAC address" provided within the DSDT/SSDT if such an
address is available and has not already been assigned to a network
device.
Tested-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RTL8211B seems to have a bug that prevents the link from coming up
unless the MII_MMD_DATA register is cleared.
The Linux kernel driver applies this workaround (in rtl8211b_resume())
only to the specific RTL8211B PHY model, along with a matching
workaround to set bit 9 of MII_MMD_DATA when suspending the PHY.
Since we have no need to ever suspend the PHY, and since writing a
zero ought to be harmless, we just clear the register unconditionally.
Debugged-by: Nikolay Pertsev <nikolay.p@cos.flag.org>
Tested-by: Nikolay Pertsev <nikolay.p@cos.flag.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hexadecimal values instead of macros in PCI_ROM entries so Perl
script can parse them correctly. Move PCI_ROM entries from header
file to C file. Integrate bnxt_vf_nics array into PCI_ROM entries by
introducing BNXT_FLAG_PCI_VF flag into driver_data field. Add
whitespaces in PCI_ROM entries for style consistency.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The use of jumbo frames for the Xen netfront virtual NIC requires the
use of scatter-gather ("feature-sg"), with the receive descriptor ring
becoming a list of page-sized buffers and the backend using as many
page buffers as required for each packet.
Since iPXE's abstraction of an I/O buffer does not include any sort of
scatter-gather list, this requires an extra allocation and copy on the
receive datapath for any packet that spans more than a single page.
This support is required in order to successfully boot an AWS EC2
virtual machine (with non-enhanced networking) via iSCSI if jumbo
frames are enabled, since the netback driver used in EC2 seems not to
allow "feature-sg" to be renegotiated once the Linux kernel driver
takes over.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Adding this missing identifier allows the X557-AT2 chipset seen on (at
least) Super Micro A2SDI-H-TF motherboards to function with iPXE.
Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com>
The GCC11 compiler pointed out something that apparently no previous
compiler noticed: in ath5k_eeprom_pread_turbo_modes, local variable
val is used uninitialized. From what I can see, the code is just
missing an initial AR5K_EEPROM_READ. Add it right before the switch
statement.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Linux and FreeBSD drivers for the (totally undocumented) ENA
adapters use a two-phase reset mechanism: first set ENA_CTRL.RESET and
wait for this to be reflected in ENA_STAT.RESET, then clear
ENA_CTRL.RESET and again wait for it to be reflected in
ENA_STAT.RESET.
The iPXE driver currently assumes a self-clearing reset mechanism,
which appeared to work at the time that the driver was created but
seems no longer to function, at least on the t3.nano and t3a.nano
instance types found in eu-west-1.
Switch to a simplified version of the two-phase reset mechanism as
used by Linux and FreeBSD.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Email from solarflare.com will stop working, so update those. Remove
email for Shradha Shah, as she is not involved with this any more.
Update copyright notices for files touched.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
USB tethering via an iPhone is unreasonably complicated due to the
requirement to perform a pairing operation that involves establishing
a TLS session over a completely unrelated USB function that speaks a
protocol that is almost, but not quite, entirely unlike TCP.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include a potential DMA mapping within the definition of an I/O
buffer, and move all I/O buffer DMA mapping functions from dma.h to
iobuf.h. This avoids the need for drivers to maintain a separate list
of DMA mappings for each I/O buffer that they may handle.
Network device drivers typically do not keep track of transmit I/O
buffers, since the network device core already maintains a transmit
queue. Drivers will typically call netdev_tx_complete_next() to
complete a transmission without first obtaining the relevant I/O
buffer pointer (and will rely on the network device core automatically
cancelling any pending transmissions when the device is closed).
To allow this driver design approach to be retained, update the
netdev_tx_complete() family of functions to automatically perform the
DMA unmapping operation if required. For symmetry, also update the
netdev_rx() family of functions to behave the same way.
As a further convenience for drivers, allow the network device core to
automatically perform DMA mapping on the transmit datapath before
calling the driver's transmit() method. This avoids the need to
introduce a mapping error handling code path into the typically
error-free transmit methods.
With these changes, the modifications required to update a typical
network device driver to use the new DMA API are fairly minimal:
- Allocate and free descriptor rings and similar coherent structures
using dma_alloc()/dma_free() rather than malloc_phys()/free_phys()
- Allocate and free receive buffers using alloc_rx_iob()/free_rx_iob()
rather than alloc_iob()/free_iob()
- Calculate DMA addresses using dma() or iob_dma() rather than
virt_to_bus()
- Set a 64-bit DMA mask if needed using dma_set_mask_64bit() and
thereafter eliminate checks on DMA address ranges
- Either record the DMA device in netdev->dma, or call iob_map_tx() as
part of the transmit() method
- Ensure that debug messages use virt_to_phys() when displaying
"hardware" addresses
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Redefine the value stored within a DMA mapping to be the offset
between physical addresses and DMA addresses within the mapped region.
Provide a dma() wrapper function to calculate the DMA address for any
pointer within a mapped region, thereby simplifying the use cases when
a device needs to be given addresses other than the region start
address.
On a platform using the "flat" DMA implementation the DMA offset for
any mapped region is always zero, with the result that dma_map() can
be optimised away completely and dma() reduces to a straightforward
call to virt_to_phys().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For the physical function driver, the transmit queue needs to be
configured to be associated with the relevant physical function
number. This is currently obtained from the bus:dev.fn address of the
underlying PCI device.
In the case of a virtual machine using the physical function via PCI
passthrough, the PCI bus:dev.fn address within the virtual machine is
unrelated to the real physical function number. Such a function will
typically be presented to the virtual machine as a single-function
device. The function number extracted from the PCI bus:dev.fn address
will therefore always be zero.
Fix by reading from the Function Requester ID Information Register,
which always returns the real PCI bus:dev.fn address as used by the
physical host.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The datasheet is fairly incomprehensible in terms of identifying the
appropriate MAC address for use by the physical function driver.
Choose to read the MAC address from PRTPM_SAH and PRTPM_SAL, which at
least matches the MAC address as selected by the Linux i40e driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Physical addresses in debug messages are more meaningful from an
end-user perspective than potentially IOMMU-mapped I/O virtual
addresses, and have the advantage of being calculable without access
to the original DMA mapping entry (e.g. when displaying an address for
a single failed completion within a descriptor ring).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For a software UNDI, the addresses in PXE_CPB_TRANSMIT.FrameAddr and
PXE_CPB_RECEIVE.BufferAddr are host addresses, not bus addresses.
Remove the spurious (and no-op) use of virt_to_bus() and replace with
a cast via intptr_t.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UEFI specification defines PXE_CPB_TRANSMIT.DataLen as excluding
the length of the media header. iPXE currently fills in DataLen as
the whole frame length (including the media header), along with
placing the media header length separately in MediaheaderLen. On some
UNDI implementations (observed using a VMware ESXi 7.0b virtual
machine), this causes transmitted packets to include 14 bytes of
trailing garbage.
Match the behaviour of the EDK2 SnpDxe driver, which fills in DataLen
as the whole frame length (including the media header) and leaves
MediaheaderLen as zero. This behaviour also violates the UEFI
specification, but is likely to work in practice since EDK2 is the
reference implementation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The malloc_dma() function allocates memory with specified physical
alignment, and is typically (though not exclusively) used to allocate
memory for DMA.
Rename to malloc_phys() to more closely match the functionality, and
to create name space for functions that specifically allocate and map
DMA-capable buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The legacy transmit descriptor index is not reset by anything short of
a full device reset. This can cause the legacy transmit ring to stall
after closing and reopening the device, since the hardware and
software indices will be out of sync.
Fix by performing a reset after closing the interface. Do this only
if operating in legacy mode, since in C+ mode the reset is not
required and would undesirably clear additional state (such as the C+
command register itself).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A zero divisor will currently lead to a 16-bit integer overflow when
calculating the transmit padding, and a potential division by zero if
assertions are enabled.
Avoid these problems by treating a divisor value of zero as equivalent
to a divisor value of one (i.e. no alignment requirements).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently use a heuristic to determine whether or not to request
cable detection in PXE_OPCODE_INITIALIZE, based on the need to work
around a known Emulex driver bug (see commit c0b61ba "[efi] Work
around bugs in Emulex NII driver") and the need to accommodate links
that are legitimately slow to come up (see commit 6324227 "[efi] Skip
cable detection at initialisation where possible").
This heuristic appears to fail with newer Emulex drivers. Attempt to
support all known drivers (past and present) by first attempting
initialisation with cable detection, then falling back to attempting
initialisation without cable detection.
Reported-by: Kwang Woo Lee <kwleeyh@gmail.com>
Tested-by: Kwang Woo Lee <kwleeyh@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When connected to a USB3 port, the AX88179 seems to have an
approximately 50% chance of producing a USB transaction error on each
of its three endpoints after being closed and reopened. The root
cause is unclear, but rewriting the USB device configuration value
seems to clear whatever internal error state has accumulated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ASIX USB NICs are capable of autodetecting the Ethernet link speed
and reporting it via PLSR but will not automatically update the
relevant GM and PS bits in MSR. The result is that a non-gigabit link
will fail to send or receive any packets.
The interrupt endpoint used to report link state includes the values
of the PHY BMSR and LPA registers. These are not sufficient to
differentiate between 100Mbps and 1000Mbps, since the LPA_NPAGE bit
does not necessarily indicate that the link partner is advertising
1000Mbps.
Extend axge_check_link() to write the MSR value based on the link
speed read from PLSR, and simplify the interrupt endpoint handler to
merely trigger a call to axge_check_link().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
GCC 10 produces a spurious warning about an out-of-bounds array access
for the unsized raw dword array in union intelvf_msg.
Avoid the warning by embedding the zero-length array within a struct.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some devices (observed with a Getac RX10 tablet and docking station
containing an embedded AX88179 USB NIC) seem to be capable of
detecting link state only during the call to Initialize(), and will
occasionally erroneously report that the link is down for the first
few such calls.
Work around these devices by retrying the Initialize() call multiple
times, terminating early if a link is detected. The eventual absence
of a link is treated as a non-fatal error, since it is entirely
possible that the link really is down.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to UEFI specification 2.8 p 24.1 we must set the
EFI_SIMPLE_NETWORK_RECEIVE_MULTICAST bit in the "Disable" mask, when
"ResetMCastFilter" is TRUE.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Split-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Currently, if the SNP driver for whatever reason fails to enable
receive filters for multicast frames, it falls back to enabling just
unicast and broadcast filters. This breaks some IPv6 functionality as
the network card does not respond to neighbour solicitation requests.
Some cards refuse to enable EFI_SIMPLE_NETWORK_RECEIVE_MULTICAST, but
do support enabling EFI_SIMPLE_NETWORK_RECEIVE_PROMISCUOUS_MULTICAST,
so try it before falling back to just unicast+broadcast.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Split-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown
Benedikt Braunger
Aaron Young
Joseph
Christian Nilsson
Tyler J. Stachecki
Bruce Rogers
Martin Habets
Rob Taglang
Ben Bleything
Andrew Grasso
LaDerrick H
Ignat Korchagin