netdev_close() assumes that devices that are open are on the
open_list, which wasn't true if device specific opening failed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "read" command allows a script to prompt a user to enter a
setting. For example:
echo -n Static IP address:
read net0/ip
Total cost: 17 bytes.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 6861304 ("[tcp] Handle out-of-order received packets")
introduced a regression in which ts_recent would not be updated until
the first packet is received in the ESTABLISHED state, i.e. the
timestamp from the SYN+ACK packet would be ignored. This causes the
connection to be dropped by strictly-conforming TCP peers, such as
FreeBSD.
Fix by delaying the timestamp window check until after processing the
received SYN flag.
Reported-by: winders@sonnet.com
Signed-off-by: Michael Brown <mcb30@ipxe.org>
bin/ipxe.lkrn is built anyway in order to create bin/ipxe.iso, so
there is no additional cost to including it within the default build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Normalise the progress figures to ensure that multiplication by 100
(to produce a percentage) cannot result in integer overflow.
Reported-by: Sven Dreyer <sven@dreyer-net.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE documentation tends to refer to "settings" rather than "options",
since settings can be more general than DHCP options.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some PXE stacks advertise that interrupts are not supported, despite
requiring the use of interrupts. Attempt to cope with such cards
without breaking others by always hooking the interrupt, and using the
"interrupts supported" flag only to decide whether or not to wait for
an interrupt before calling PXENV_UNDI_ISR_IN_PROCESS.
The possible combinations are therefore:
1. Card generates interrupts and claims to support interrupts
iPXE will call PXENV_UNDI_ISR_IN_PROCESS only after an interrupt
has been observed. (This is required to avoid lockups in some PXE
stacks, which spuriously sulk if called before an interrupt has
been generated.)
Such a card should work correctly.
2. Card does not generate interrupts and does not claim to support
interrupts
iPXE will call PXENV_UNDI_ISR_IN_PROCESS indiscriminately, matching
the observed behaviour of at least one other PXE NBP (winBoot/i).
Such a card should work correctly.
3. Card generates interrupts but claims not to support interrupts
iPXE will call PXENV_UNDI_ISR_IN_PROCESS indiscriminately. An
interrupt will still result in a call to PXENV_UNDI_ISR_IN_START.
Such a card may work correctly.
4. Card does not generate interrupts but claims to support interrupts
Such a card will not work at all.
Reported-by: Jerry Cheng <jaspers.cheng@msa.hinet.net>
Tested-by: Jerry Cheng <jaspers.cheng@msa.hinet.net>
Reported-by: Mauricio Silveira <mauricio@livreti.com.br>
Tested-by: Mauricio Silveira <mauricio@livreti.com.br>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the appearance of the "config" user interface by ensuring that
settings appear in some kind of logical order.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5fbd020 ("[settings] Display canonical setting name in output
of "show" command") introduced a regression causing all setting
expansions (e.g. "${net0/mac}") to expand to an empty string.
Fix by returning the formatted value length from
fetchf_named_setting(), as expected by the caller.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the user to browse through the settings block hierarchy.
Originally-implemented-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Display only settings relevant to the current scope. For example,
"config net0" no longer displays SMBIOS settings, and "config smbios"
displays only SMBIOS settings.
Originally-implemented-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Enable the "show" command to display the full, canonicalised name of
the fetched setting. For example:
iPXE> show mac
net0/mac:hex = 52:54:00:12:34:56
iPXE> dhcp && show ip
DHCP (net0 52:54:00:12:34:56)... ok
net0.dhcp/ip:ipv4 = 10.0.0.168
iPXE> show net0/6
net0.dhcp/dns:ipv4 = 10.0.0.6
Inspired-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose settings_name(), shrink the unnecessarily large static buffer,
properly name root settings block, and simplify.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose a function setting_applies() to allow a caller to determine
whether or not a particular setting is applicable to a particular
settings block.
Restrict DHCP-backed settings blocks to accepting only DHCP-based
settings.
Restrict network device settings blocks to accepting only DHCP-based
settings and network device-specific settings such as "mac".
Inspired-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "us" keyboard layout contains a mapping for keycode 86 (which
seems not to correspond to any physical key on many US keyboards) to
the ASCII character '<'. This mapping causes conflicts with the
mapping for keycode 51, which also maps (with shift) to '<'.
Change the keyboard mapping generator to choose the lowest keycode for
each ASCII character as indicating the relevant mapping to use, on the
basis that a lower keycode roughly indicates a "more normal" key. On
a German keyboard, which has keys for both keycode 51 and keycode 86
present, this causes '<' to be remapped to ';', which is a closer
match to typical user expectations.
Reported-by: Sven Dreyer <sven@dreyer-net.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
From a cursory examination, it appears as though the calculation of
tx_available is redundant, since eepro_transmit() waits for transmit
completion before returning anyway.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On reset and close, the ICR register is read to clear any pending
interrupts, but the value is simply ignored. Avoid assigning the
value to a variable, to inhibit a warning from gcc 4.6.
Also fix a potential race condition in reset routines which clear
interrupts before disabling them.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
These unused portions trigger a compiler warning under gcc 4.6, due to
the ambiguity over the "page" field in struct igbvf_buffer.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A construction such as "assert ( ptr != NULL )" seems to trigger a
false positive warning in gcc 4.6 if the value of "ptr" is known at
compile-time to be non-NULL. Use -Wno-address to inhibit this
warning.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The __table_entries() construction seems to trigger a false positive
warning in gcc 4.6 relating to variables which are set but never
used. Add __attribute__((unused)) to inhibit this warning.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The keymap files, though autogenerated, are checked in to version
control and should be considered as source files. They should never
be automatically rebuilt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Inspired by LILO's keytab-lilo.pl, genkeymap.pl uses "loadkeys -b" to
obtain a Linux keyboard map, and generates a file keymap_xx.c in
hci/keymap.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Re-open the EFI_PCI_IO_PROTOCOL specifying an Attributes value of
EFI_OPEN_PROTOCOL_BY_CHILD_CONTROLLER. This causes the SNP devices to
be marked as children of the EFI PCI device (as shown in the "devtree"
command).
On at least one IBM blade system, this is required in order to have
the relevant drivers automatically attach to the SNP controller at
device creation time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE allocates its first PMM block using the image source length,
which is rounded up to the nearest 16-byte paragraph. It then copies
in data of a length calculated from the ROM size, which is
theoretically less than or equal to the image source length, but is
rounded up to the nearest 512-byte sector. This can result in copying
beyond the end of the allocated PMM block, which can corrupt the PMM
data structures (and other essentially arbitrary areas of memory).
Fix by rounding up the image source length to the nearest 512-byte
sector before using it as the PMM allocation length.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Jarrod Johnson <jarrod.b.johnson@gmail.com>
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a virtual environment such as qemu, we can legitimately receive
packets less than 64 bytes in length, such as ARP replies. These are
currently discarded, causing most IPv4 communication to fail.
Fix by ignoring the RFDShort bit when receiving packets.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
INT 16,01 will discard some extended keystrokes on some BIOSes, making
it impossible for iPXE to detect keypresses such as F12. Fix by using
INT 16,11 instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A script that downloads a new image using imgdownload() with the
action register_and_replace_image() can now be freed immediately
before the replacement image is executed. This functionality is not
yet exposed via an iPXE command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
These functions are used only as the "action" parameters to
imgdownload() or imgfetch(), and so belong in imgmgmt.c rather than
image.c
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some prefixes (e.g. .lkrn) allow a command line to be passed in to
iPXE. At present, this command line is ignored.
If a command line is provided, treat it as an embedded script (without
an explicit "#!ipxe" magic marker). This allows for patterns of
invocation such as
title iPXE
kernel /boot/ipxe.lkrn dhcp && \
sanboot iscsi:10.0.4.1::::iqn.2010-04.org.ipxe.dolphin:storage
Here GRUB is instructed to load ipxe.lkrn with an embedded script
equivalent to
#!ipxe
dhcp
sanboot iscsi:10.0.4.1::::iqn.2010-04.org.ipxe.dolphin:storage
This can be used to effectively vary the embedded script without
having to rebuild ipxe.lkrn.
Originally-implemented-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "prompt" command exposes the prompt() function, allowing a script
to prompt the user for a keypress and take action depending on the
result. For example
#!ipxe
prompt -k 0x197e -t 2000 Press F12 to boot from network... || exit
autoboot
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The function keys F5-F12 all conform to the same ANSI pattern as the
other "special" keys that we currently recognise. Add these key
definitions, and shrink the representation of the ANSI sequences in
bios_console.c to compensate.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Refactor the {load,exec} image operations as {probe,exec}. This makes
the probe mechanism cleaner, eliminates some forward declarations,
avoids holding magic state in image->priv, eliminates the possibility
of screwing up between the "load" and "exec" stages, and makes the
documentation simpler since the concept of "loading" (as distinct from
"executing") no longer needs to be explained.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading rtl8139.pxe from an old Etherboot rtl8139.zrom, iPXE
can end up misreading the first word of the MAC address from the
EEPROM as being all zeroes. This is presumably because Etherboot has
left the serial EEPROM in an unexpected state.
Fix by using the chip select line to reset the SPI device before we
start accessing it.
Reported-by: Mandar U Jog <mandarjog@gmail.com>
Tested-by: Mandar U Jog <mandarjog@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The online documentation (e.g. http://ipxe.org/cmd/ifopen), though not
yet complete, is far more comprehensive than could be provided within
the iPXE binary. Save around 200 bytes (compressed) by removing the
command descriptions from the interactive help, and instead referring
users directly to the web page describing the relevant command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default initiator IQN is "iqn.2000-09.org.etherboot:UNKNOWN".
This is problematic for two reasons:
a) the etherboot.org domain (and hence the associated IQN namespace)
is not under the control of the iPXE project, and
b) some targets (correctly) refuse to allow concurrent connections
from different initiators using the same initiator IQN.
Solve both problems by changing the default initiator IQN to be
iqn.2010-04.org.ipxe:<hostname> if a hostname is set, or
iqn.2010-04.org.ipxe:<uuid> if no hostname is set.
Explicit initiator IQNs set via DHCP option 203 are not affected by
this change.
Unfortunately, this change is likely to break some existing
configurations, where ACL rules have been put in place referring to
the old default initiator IQN. Users may need to update ACLs, or
force the use of the old IQN using an iPXE script line such as
set initiator-iqn iqn.2000-09.org.etherboot:UNKNOWN
or a dhcpd.conf option such as
option iscsi-initiator-iqn "iqn.2000-09.org.etherboot:UNKNOWN"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most callers of functions in the fetch_setting() family treat any
errors as meaning "non-existent setting". In the case of
fetch_string_setting_copy(), an existent setting can still result in
an error due to memory allocation failure.
Allow the caller to distinguish between a non-existent setting and an
error in allocating memory for the copy, by returning success (and a
NULL buffer pointer) for a non-existent setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For consistency with other functions in the fetch_setting() family,
ensure that fetch_string_setting_copy() always initialises the pointer
to the fetched setting even if fetching fails.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most builds will not have BOFM enabled. In these builds, allow all
BOFM code (including BOFM-only code within the individual drivers) to
be garbage-collected at link time in order to save space in the final
binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Testing BOFM involves gaining access to an IBM blade chassis, which is
often not practical. Provide a facility for testing BOFM
functionality outside of a real IBM blade context.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Currently, if both a filename and root-path are present, iPXE will
hook the SAN device but will only attempt to boot from the filename.
Change this behaviour so that both are attempted. Users who want to
avoid booting from the SAN as a fallback can do so via the existing
"skip-san-boot" setting.
This allows for seamless deployment to a SAN target using Windows
Deployment Services (and similar products). A user simply has to
define the root-path option in DHCP and then use WDS to deploy the
system. No further configuration should be required.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the NBP returns, then always print a trailing newline, since some
NBPs (e.g. wdsnbp.com) leave the cursor in a random position halfway
across the screen.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the monojob controlling the download to complete before calling
register_image() and friends. This allows the trailing "ok" from
monojob.c to be printed before the image starts executing (and
possibly printing output of its own).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Piotr Jaroszyński
Michael Brown
Glenn Brown
Yann Cézard
Bastian Blank