Allow the ACPI power management timer to be used if enabled via
TIMER_ACPI in config/timer.h. This provides an alternative timer on
systems where the standard 8254 PIT is unavailable or unreliable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older operating systems (e.g. RHEL6) use a non-default filename
on the root disk and rely on setting an EFI variable to point to the
bootloader. This does not work when performing a SAN boot on a
machine where the EFI variable is not present.
Fix by allowing a non-default filename to be specified via the
"sanboot --filename" option or the "san-filename" setting. For
example:
sanboot --filename \efi\redhat\grub.efi \
iscsi:192.168.0.1::::iqn.2010-04.org.ipxe.demo:rhel6
or
option ipxe.san-filename code 188 = string;
option ipxe.san-filename "\\efi\\redhat\\grub.efi";
option root-path "iscsi:192.168.0.1::::iqn.2010-04.org.ipxe.demo:rhel6";
Originally-implemented-by: Vishvananda Ishaya Abrams <vish.ishaya@oracle.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Describe all SAN devices via ACPI tables such as the iBFT. For tables
that can describe only a single device (i.e. the aBFT and sBFT), one
table is installed per device. For multi-device tables (i.e. the
iBFT), all devices are described in a single table.
An underlying SAN device connection may be closed at the time that we
need to construct an ACPI table. We therefore introduce the concept
of an "ACPI descriptor" which enables the SAN boot code to maintain an
opaque pointer to the underlying object, and an "ACPI model" which can
build tables from a list of such descriptors. This separates the
lifecycles of ACPI descriptions from the lifecycles of the block
device interfaces, and allows for construction of the ACPI tables even
if the block device interface has been closed.
For a multipath SAN device, iPXE will wait until sufficient
information is available to describe all devices but will not wait for
all paths to connect successfully. For example: with a multipath
iSCSI boot iPXE will wait until at least one path has become available
and name resolution has completed on all other paths. We do this
since the iBFT has to include IP addresses rather than DNS names. We
will commence booting without waiting for the inactive paths to either
become available or close; this avoids unnecessary boot delays.
Note that the Linux kernel will refuse to accept an iBFT with more
than two NIC or target structures. We therefore describe only the
NICs that are actually required in order to reach the described
targets. Any iBFT with at most two targets is therefore guaranteed to
describe at most two NICs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The INT13 console type (CONSOLE_INT13) autodetects at initialisation
time a magic partition to be used for logging iPXE console output. If
the INT13 drive number mapping is subsequently changed (e.g. because
iPXE was used to perform a SAN boot), then the console logging output
will be written to the incorrect disk.
Fix by recording the INT13 vector at initialisation time, and using
this original vector to emulate INT13 calls for all subsequent
accesses. This should be robust against drive remapping performed
either by ourselves or by another bootloader (e.g. a chainloaded
undionly.kpxe which then performs a SAN boot).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some partition tables have partitions that are not aligned to a
cylinder boundary, which confuses the current geometry guessing logic.
Enhance the existing logic to ensure that we never reduce our guesses
for the number of heads or sectors per track, and add extra logic to
calculate the exact number of sectors per track if we find a partition
that starts within cylinder zero.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add basic support for multipath block devices. The "sanboot" and
"sanhook" commands now accept a list of SAN URIs. We open all URIs
concurrently. The first connection to become available for issuing
block device commands is marked as the active path and used for all
subsequent commands; all other connections are then closed. Whenever
the active path fails, we reopen all URIs and repeat the process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As of commit 10d19bd ("[pxe] Always retrieve cached DHCPACK and apply
to relevant network device"), the UNDI driver has been the only user
of pxeparent_call(). Remove the unnecessary layer of abstraction by
refactoring this code back into undinet.c, and fix the ability of
undiisr.S to fall back to chaining to the original handler if we were
unable to unhook our own ISR.
This effectively reverts commit 337e1ed ("[pxe] Separate parent PXE
API caller from UNDINET driver").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The concept of the SAN drive number is meaningful only in a BIOS
environment, where it represents the INT13 drive number (0x80 for the
first hard disk). We retain this concept in a UEFI environment to
allow for a simple way for iPXE commands to refer to SAN drives.
Centralise the concept of the default drive number, since it is shared
between all supported environments.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
INT 13 calls return a status value via %ah, with CF set if %ah is
non-zero (indicating an error). Our wrappers zero the whole of %ax if
CF is clear, to allow C code (which has no easy access to CF) to
simply test for a non-zero status to detect an error.
The current code assigns the returned status to a uint8_t, effectively
testing %al rather than %ah. Fix by treating the returned status as a
uint16_t instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid using a zero sector count to guess the disk geometry, since that
would result in a division by zero when calculating the number of
cylinders.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the active timer (providing udelay() and currticks()) to be
selected at runtime based on probing during the INIT_EARLY stage of
initialisation.
TICKS_PER_SEC is now a fixed compile-time constant for all builds, and
is independent of the underlying clock tick rate. We choose the value
1024 to allow multiplications and divisions on seconds to be converted
to bit shifts.
TICKS_PER_MS is defined as 1, allowing multiplications and divisions
on milliseconds to be omitted entirely. The 2% inaccuracy in this
definition is negligible when using the standard BIOS timer (running
at around 18.2Hz).
TIMER_RDTSC now checks for a constant TSC before claiming to be a
usable timer. (This timer can be tested in KVM via the command-line
option "-cpu host,+invtsc".)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ACPI power off sequence may not take effect immediately. Delay
for one second, to eliminate potentially confusing log messages such
as "Could not power off: Error 0x43902001 (http://ipx".
Reported-by: Leonid Vasetsky <leonidv@velostrata.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some platforms (observed in a small subset of Microsoft Azure
(Hyper-V) virtual machines), the RTC appears to be incapable of
generating an interrupt via the legacy PIC. The RTC status registers
show that a periodic interrupt has been asserted, but the PIC IRR
shows that IRQ8 remains inactive.
On such systems, iPXE will currently freeze during the "iPXE
initialising devices..." message.
Work around this problem by checking that RTC interrupts are being
raised before returning from rtc_entropy_enable(). If no interrupt is
seen within 100ms, then we assume that the RTC interrupt mechanism is
broken. In these circumstances, iPXE will continue to initialise but
any subsequent attempt to generate entropy will fail. In particular,
HTTPS connections will fail with an error indicating that no entropy
is available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There seems to be no reason for the sti/cli pair used around each call
to INT 10. Remove these instructions, so that printing debug messages
from within an ISR does not temporarily reenable interrupts.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some end-user configurations have been observed in which the first NBP
(such as GRUB2) uses the UNDI API and then transfers control to a
second NBP (such as pxelinux) which uses the UDP API. The first NBP
closes the network device using PXENV_UNDI_CLOSE, which renders the
UDP API unable to transmit or receive packets.
The correct behaviour under these circumstances is (as often) simply
not documented by the PXE specification. Testing with the Intel PXE
stack suggests that PXENV_UDP_OPEN will implicitly reopen the network
device if necessary, so match this behaviour.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The DHCP option 175.189 has been defined (by us) since 2006 as
containing the drive number to be used for a SAN boot, but has never
been automatically used as such by iPXE.
Use this option (if specified) to override the default SAN drive
number.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Interpret the maximum drive number (0xff for hard disks, 0x7f for
floppy disks) as meaning "use natural drive number".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When running the 64-bit BIOS version of iPXE, restrict external memory
allocations to the low 4GB to ensure that allocations (such as for
initrds) fall within our identity-mapped memory region, and will be
accessible to the potentially 32-bit operating system.
Move largest_memblock() back to memtop_umalloc.c, since this change
imposes a restriction that applies only to BIOS builds.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a 64-bit CPU, any modification of a register by 32-bit or 16-bit
code will destroy the invisible upper 32 bits of the corresponding
64-bit register. For example: a 32-bit "pushl %eax" followed by a
"popl %eax" will zero the upper half of %rax. This differs from the
treatment of upper halves of 32-bit registers by 16-bit code: a
"pushw %ax" followed by a "popw %ax" will leave the upper 16 bits of
%eax unmodified.
Inline assembly generated using REAL_CODE() or PHYS_CODE() will
therefore have to preserve the upper halves of all registers, to avoid
clobbering registers that gcc expects to be preserved.
Output operands from REAL_CODE() and PHYS_CODE() assembly may
therefore contain undefined values in the upper 32 bits.
Fix by using explicit variable widths (e.g. uint32_t) for
non-discarded output operands, to ensure that undefined values in the
upper 32 bits of 64-bit registers are ignored.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move most arch/i386 files to arch/x86, and adjust the contents of the
Makefiles and the include/bits/*.h headers to reflect the new
locations.
This patch makes no substantive code changes, as can be seen using a
rename-aware diff (e.g. "git show -M5").
This patch does not make the pcbios platform functional for x86_64; it
merely allows it to compile without errors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The GuestRPC mechanism (used for VMWARE_SETTINGS and CONSOLE_VMWARE)
does not use any real-mode code and so can be exposed in both 64-bit
and 32-bit builds.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Entropy gathering via timer ticks is slow under UEFI (of the order of
20-30 seconds on some machines). Use the EFI_RNG_PROTOCOL if
available, to speed up the process of entropy gathering.
Note that some implementations (including EDK2) will fail if we
request fewer than 32 random bytes at a time, and that the RNG
protocol provides no guarantees about the amount of entropy provided
by a call to GetRNG(). We take the (hopefully pessimistic) view that
a 32-byte block returned by GetRNG() will contain at least the 1.3
bits of entropy claimed by min_entropy_per_sample().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Currently the only supported platform for x86_64 is EFI.
Building an EFI64 gPXE requires a version of gcc that supports
__attribute__((ms_abi)). This currently means a development build of
gcc; the feature should be present when gcc 4.4 is released.
In the meantime; you can grab a suitable gcc tree from
git://git.etherboot.org/scm/people/mcb30/gcc/.git
Michael Brown
Michael Brown