mirror of https://github.com/ipxe/ipxe.git
[mii] Remove unused functionality
Signed-off-by: Michael Brown <mcb30@ipxe.org>pull/6/head
Michael Brown
parent
eadb6bc3fe
commit
2f3f0ca953
|
|
@ -157,63 +157,4 @@ struct mii_if_info {
|
|||
void (*mdio_write) (struct net_device *dev, int phy_id, int location, int val);
|
||||
};
|
||||
|
||||
|
||||
extern int mii_link_ok (struct mii_if_info *mii);
|
||||
extern void mii_check_link (struct mii_if_info *mii);
|
||||
extern unsigned int mii_check_media (struct mii_if_info *mii,
|
||||
unsigned int ok_to_print,
|
||||
unsigned int init_media);
|
||||
|
||||
|
||||
/**
|
||||
* mii_nway_result
|
||||
* @negotiated: value of MII ANAR and'd with ANLPAR
|
||||
*
|
||||
* Given a set of MII abilities, check each bit and returns the
|
||||
* currently supported media, in the priority order defined by
|
||||
* IEEE 802.3u. We use LPA_xxx constants but note this is not the
|
||||
* value of LPA solely, as described above.
|
||||
*
|
||||
* The one exception to IEEE 802.3u is that 100baseT4 is placed
|
||||
* between 100T-full and 100T-half. If your phy does not support
|
||||
* 100T4 this is fine. If your phy places 100T4 elsewhere in the
|
||||
* priority order, you will need to roll your own function.
|
||||
*/
|
||||
static inline unsigned int mii_nway_result (unsigned int negotiated)
|
||||
{
|
||||
unsigned int ret;
|
||||
|
||||
if (negotiated & LPA_100FULL)
|
||||
ret = LPA_100FULL;
|
||||
else if (negotiated & LPA_100BASE4)
|
||||
ret = LPA_100BASE4;
|
||||
else if (negotiated & LPA_100HALF)
|
||||
ret = LPA_100HALF;
|
||||
else if (negotiated & LPA_10FULL)
|
||||
ret = LPA_10FULL;
|
||||
else
|
||||
ret = LPA_10HALF;
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
/**
|
||||
* mii_duplex
|
||||
* @duplex_lock: Non-zero if duplex is locked at full
|
||||
* @negotiated: value of MII ANAR and'd with ANLPAR
|
||||
*
|
||||
* A small helper function for a common case. Returns one
|
||||
* if the media is operating or locked at full duplex, and
|
||||
* returns zero otherwise.
|
||||
*/
|
||||
static inline unsigned int mii_duplex (unsigned int duplex_lock,
|
||||
unsigned int negotiated)
|
||||
{
|
||||
if (duplex_lock)
|
||||
return 1;
|
||||
if (mii_nway_result(negotiated) & LPA_DUPLEX)
|
||||
return 1;
|
||||
return 0;
|
||||
}
|
||||
|
||||
#endif
|
||||
|
|
|
|||
147
src/net/mii.c
147
src/net/mii.c
|
|
@ -1,147 +0,0 @@
|
|||
/*
|
||||
|
||||
mii.c: MII interface library
|
||||
|
||||
Ported to iPXE by Daniel Verkamp <daniel@drv.nu>
|
||||
from Linux drivers/net/mii.c
|
||||
|
||||
Maintained by Jeff Garzik <jgarzik@pobox.com>
|
||||
Copyright 2001,2002 Jeff Garzik
|
||||
|
||||
Various code came from myson803.c and other files by
|
||||
Donald Becker. Copyright:
|
||||
|
||||
Written 1998-2002 by Donald Becker.
|
||||
|
||||
This software may be used and distributed according
|
||||
to the terms of the GNU General Public License (GPL),
|
||||
incorporated herein by reference. Drivers based on
|
||||
or derived from this code fall under the GPL and must
|
||||
retain the authorship, copyright and license notice.
|
||||
This file is not a complete program and may only be
|
||||
used when the entire operating system is licensed
|
||||
under the GPL.
|
||||
|
||||
The author may be reached as becker@scyld.com, or C/O
|
||||
Scyld Computing Corporation
|
||||
410 Severn Ave., Suite 210
|
||||
Annapolis MD 21403
|
||||
|
||||
*/
|
||||
|
||||
#include <mii.h>
|
||||
|
||||
/**
|
||||
* mii_link_ok - is link status up/ok
|
||||
* @mii: the MII interface
|
||||
*
|
||||
* Returns 1 if the MII reports link status up/ok, 0 otherwise.
|
||||
*/
|
||||
int
|
||||
mii_link_ok ( struct mii_if_info *mii )
|
||||
{
|
||||
/* first, a dummy read, needed to latch some MII phys */
|
||||
mii->mdio_read ( mii->dev, mii->phy_id, MII_BMSR );
|
||||
if ( mii->mdio_read ( mii->dev, mii->phy_id, MII_BMSR ) & BMSR_LSTATUS )
|
||||
return 1;
|
||||
return 0;
|
||||
}
|
||||
|
||||
/**
|
||||
* mii_check_link - check MII link status
|
||||
* @mii: MII interface
|
||||
*
|
||||
* If the link status changed (previous != current), call
|
||||
* netif_carrier_on() if current link status is Up or call
|
||||
* netif_carrier_off() if current link status is Down.
|
||||
*/
|
||||
void
|
||||
mii_check_link ( struct mii_if_info *mii )
|
||||
{
|
||||
int cur_link = mii_link_ok ( mii );
|
||||
int prev_link = netdev_link_ok ( mii->dev );
|
||||
|
||||
if ( cur_link && !prev_link )
|
||||
netdev_link_up ( mii->dev );
|
||||
else if (prev_link && !cur_link)
|
||||
netdev_link_down ( mii->dev );
|
||||
}
|
||||
|
||||
|
||||
/**
|
||||
* mii_check_media - check the MII interface for a duplex change
|
||||
* @mii: the MII interface
|
||||
* @ok_to_print: OK to print link up/down messages
|
||||
* @init_media: OK to save duplex mode in @mii
|
||||
*
|
||||
* Returns 1 if the duplex mode changed, 0 if not.
|
||||
* If the media type is forced, always returns 0.
|
||||
*/
|
||||
unsigned int
|
||||
mii_check_media ( struct mii_if_info *mii,
|
||||
unsigned int ok_to_print,
|
||||
unsigned int init_media )
|
||||
{
|
||||
unsigned int old_carrier, new_carrier;
|
||||
int advertise, lpa, media, duplex;
|
||||
int lpa2 = 0;
|
||||
|
||||
/* if forced media, go no further */
|
||||
if (mii->force_media)
|
||||
return 0; /* duplex did not change */
|
||||
|
||||
/* check current and old link status */
|
||||
old_carrier = netdev_link_ok ( mii->dev ) ? 1 : 0;
|
||||
new_carrier = (unsigned int) mii_link_ok ( mii );
|
||||
|
||||
/* if carrier state did not change, this is a "bounce",
|
||||
* just exit as everything is already set correctly
|
||||
*/
|
||||
if ( ( ! init_media ) && ( old_carrier == new_carrier ) )
|
||||
return 0; /* duplex did not change */
|
||||
|
||||
/* no carrier, nothing much to do */
|
||||
if ( ! new_carrier ) {
|
||||
netdev_link_down ( mii->dev );
|
||||
if ( ok_to_print )
|
||||
DBG ( "%s: link down\n", mii->dev->name);
|
||||
return 0; /* duplex did not change */
|
||||
}
|
||||
|
||||
/*
|
||||
* we have carrier, see who's on the other end
|
||||
*/
|
||||
netdev_link_up ( mii->dev );
|
||||
|
||||
/* get MII advertise and LPA values */
|
||||
if ( ( ! init_media ) && ( mii->advertising ) ) {
|
||||
advertise = mii->advertising;
|
||||
} else {
|
||||
advertise = mii->mdio_read ( mii->dev, mii->phy_id, MII_ADVERTISE );
|
||||
mii->advertising = advertise;
|
||||
}
|
||||
lpa = mii->mdio_read ( mii->dev, mii->phy_id, MII_LPA );
|
||||
if ( mii->supports_gmii )
|
||||
lpa2 = mii->mdio_read ( mii->dev, mii->phy_id, MII_STAT1000 );
|
||||
|
||||
/* figure out media and duplex from advertise and LPA values */
|
||||
media = mii_nway_result ( lpa & advertise );
|
||||
duplex = ( media & ADVERTISE_FULL ) ? 1 : 0;
|
||||
if ( lpa2 & LPA_1000FULL )
|
||||
duplex = 1;
|
||||
|
||||
if ( ok_to_print )
|
||||
DBG ( "%s: link up, %sMbps, %s-duplex, lpa 0x%04X\n",
|
||||
mii->dev->name,
|
||||
lpa2 & ( LPA_1000FULL | LPA_1000HALF ) ? "1000" :
|
||||
media & ( ADVERTISE_100FULL | ADVERTISE_100HALF ) ? "100" : "10",
|
||||
duplex ? "full" : "half",
|
||||
lpa);
|
||||
|
||||
if ( ( init_media ) || ( mii->full_duplex != duplex ) ) {
|
||||
mii->full_duplex = duplex;
|
||||
return 1; /* duplex changed */
|
||||
}
|
||||
|
||||
return 0; /* duplex did not change */
|
||||
}
|
||||
Loading…
Reference in New Issue